Gebruiksaanwijzing /service van het product ISIHP-2S van de fabrikant Multi-Tech Systems
Ga naar pagina of 63
MultiModemISI Hybrid Series Model ISIHP-2S/2U Quick Start Guide.
MultiModemISI Hybrid SeriesModel ISIHP-2S/2U Quick S tart Guide 82093800 Revision A All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-T ech Systems, Inc. All rights reserved.
Contents Introduction .................................................................................................. 4 W elcome and Product Description ............................................................... 4 Peripiheral Component Interconnect (PCI) .
Introduction 4 MultiModemISI Hybrid Series, ISIHP-2S/2U elcome to Multi-Techs new MultiModemISI Hybrid Series, model ISIHP-2S/2U, a multiport hybrid ISDN card that can be W plugged into any PCI slot for Remote Access Server (RAS) applications. Included on the ISIHP-2S/2U are four V.
Introduction MultiModemISI Hybrid Series, ISIHP-2S/2U 4 From the perspective of the server PC, the ISIHP-2S/2U is an eight- port serial card with eight devices permanently attached to the serial ports. The first four ports are the two terminal adapters, each of which appear as two ports.
6 MultiModemISI Hybrid Series, ISIHP-2S/2U Hardware Installation Introduction This section describes how to install the ISIHP-2S/2U server card into the PCI bus on your personal computer, which involv.
MultiModemISI Hybrid Series, ISIHP-2S/2U 7 Hardware Installation Safety W arnings Never install telephone wiring during a lightning storm. Never install telephone jacks in wet locations unless the jacks are specifically designed for wet locations.
8 MultiModemISI Hybrid Series, ISIHP-2S/2U Hardware Installation Intelligent Serial Interface Hybrid (ISDN/POTS) Cards ( Side View ) International ISIHP-2S U.S. Domestic ISIHP-2U 4. T o avoid damaging the ISIHP-2S/2U and your PC, make sure your computer and any peripheral equipment connected to it are turned off.
MultiModemISI Hybrid Series, ISIHP-2S/2U 9 Hardware Installation NT1 Device ISIHP -2S U Interface S Interface S/T Interface ISDN line enters building Note : The ISIHP-2S/2U communicates over ISDN lines. If you don t have a standar d modular jack near your computer , you should install one or have one installed by your telephone company .
10 MultiModemISI Hybrid Series, ISIHP-2S/2U Hardware Installation LINE 2 B2 B1 LINE 1 B2 B1 LED Indicators The mounting bracket for both the ISIHI-2S and the ISIHI-2U is similar , except the LEDs are labeled dif ferently . Each mounting bracket has two sets of LED indicators that indicate status and line activity .
MultiModemISI Hybrid Series, ISIHP-2S/2U 11 Hardware Installation ISIHP-2U LED Indicators P LED Indicator Indicates U interface status connection. Controlled by NT -1, which converts S/T interface (4-wire ISDN) to U interface (2-wire ISDN). When U interface and S/T interface are NOT active, LED remains of f.
12 MultiModemISI Hybrid Series, ISIHP-2S/2U Hardware Installation Installing the ISIHP-2S/2U in Windows NT 3.51/4.0 The following procedure describes how to install the ISIHP-2S/2U in a system operating Microsoft Windows NT 3.51 or 4.0 for use with Remote Access Service (RAS) server and other communications/fax server type applications.
Software/Driver Installation (W indows NT) MultiModemISI Hybrid Series, ISIHP-2S/2U 13 5. The Insert Disk dialog box appears. Insert the MultiModem ISI Driver for W indows NT diskette and click OK . 6. The Select OEM Option dialog box appears. Click OK .
Software/Driver Installation (Windows NT) 14 MultiModemISI Hybrid Series, ISIHP-2S/2U A transient dialog box will appear while the setup program is loaded from the diskette to the PC hard drive.
Software/Driver Installation (W indows NT) MultiModemISI Hybrid Series, ISIHP-2S/2U 15 8. Then this ISI Cards dialog box appears. Select the starting port (usually port 3). 9. The ISI Cards dialog box appears again showing the port assignment. Click Add to add additional cards and repeat step 8.
Software/Driver Installation (Windows NT) 16 MultiModemISI Hybrid Series, ISIHP-2S/2U After the last ISIHP/2S/2U card has been added, click Close . 10. The file copies and Multi-T ech ISIHP-2S/2U Adapter appears in the Network Adapters box. Click Close .
Software/Driver Installation (W indows NT) MultiModemISI Hybrid Series, ISIHP-2S/2U 17 Installing T As and Modems to COM Ports in Windows NT T o install terminal adapters: 1. In the Control Panel , double-click the Modems icon. 2. The Modem Properties dialog box appears.
Software/Driver Installation (Windows NT) 18 MultiModemISI Hybrid Series, ISIHP-2S/2U 5. The Install Fr om Disk dialog box appears. Click OK (diskette should still be in drive). 6. The Install New Modem dialog box appears. From the Models list, select an ISDN protocol (; Auto-Protocol, ML-PPP , PPP , V .
Software/Driver Installation (W indows NT) MultiModemISI Hybrid Series, ISIHP-2S/2U 19 7. The Install New Modem dialog box appears. Select the ports that correspond to the first four ports of the ISIHP-2S/2U card. A ny ports that existed prior to installing the ISIHP-2S/2U appear first in the list of available COM ports.
Software/Driver Installation (Windows NT) 20 MultiModemISI Hybrid Series, ISIHP-2S/2U T o install modems: 1. In the General tab, click Add . 2. The Install New Modem dialog box appears. Check the box marked Don't detect my modem; I will select it fr om a list.
Software/Driver Installation (W indows NT) MultiModemISI Hybrid Series, ISIHP-2S/2U 21 3. The Install New Modem dialog box appears. From the Models list, select Central Site Modems for the modems . Then click Next . 4. Select the ports that correspond to the last four ports of the ISIHP- 2S/2U card.
Software/Driver Installation (Windows NT) 22 MultiModemISI Hybrid Series, ISIHP-2S/2U 5. After the modems install to the ports, click Finish to return to the General tab. 6. T o view COM port assignments and make necessary changes, use the Modem Properties dialog box.
Software/Driver Installation (Windows 95) MultiModemISI Hybrid Series, ISIHP-2S/2U 23 7. Close the Modems Properties dialog box. The message below appears asking if you want to configure dial-up networking. Click Ye s . 8. The Remote Access Setup dialog box appears.
Software/Driver Installation (Windows 95) 24 MultiModemISI Hybrid Series, ISIHP-2S/2U 1 1. When all devices have been added, click Continue . 12. After the bindings have been reviewed and stored, the message below appears, click Ye s . After re-booting, the ISI Cards icon appears in the Control Panel.
Software/Driver Installation (Windows 95) MultiModemISI Hybrid Series, ISIHP-2S/2U 25 I/O Addresses and IRQ Codes Unlike many modem products, the ISIHP-2S/2U has no DIP switch for I/O addresses and no jumper to determine the IRQ code.
Software/Driver Installation (Windows 95) 26 MultiModemISI Hybrid Series, ISIHP-2S/2U Removing ISIHP-2S/2U Card and Driver in Windows NT 3.51/4.0 1. Click S tart , Settings , Control Panel , and then double-click Network . 2. The Network dialog box appears.
Software/Driver Installation (Windows 95) MultiModemISI Hybrid Series, ISIHP-2S/2U 27 4. W indows 95 automatically searches for the unknown device and locates the MultiT ech ISI Port. After the operating system goes through this process for every port added, click Finish .
Software/Driver Installation (Windows 95) 28 MultiModemISI Hybrid Series, ISIHP-2S/2U To Remove the ISIHP-2S/2U Card and Drivers in Windows 95 T o remove the ISIHP-2S/2U: 1. Click S tar t , Settings , Control Panel , and then System . 2. The System Pr operties dialog box appears.
Software/Driver Installation (Windows 95) MultiModemISI Hybrid Series, ISIHP-2S/2U 29 4. In the next W izard dialog box, select Search for the best driver for your device. (Recommended). Then click Next . 5. In the next W izard dialog box, make sure Floppy disk drives is checked.
Software/Driver Installation (Windows 95) 30 MultiModemISI Hybrid Series, ISIHP-2S/2U 6. When this W izard dialog box appears, click Next . 7. W indows then installs the device driver for the ISIHP-2S/2U card. When this dialog box appears, click Finish .
Software/Driver Installation (Windows 95) MultiModemISI Hybrid Series, ISIHP-2S/2U 31 9. T o view the COM ports, click Control Panel and double-click System . The System Pr operties dialog box appears. The MultiTech PCI ISI Card is located under Multi Port Adapter .
Software/Driver Installation (Windows 95) 32 MultiModemISI Hybrid Series, ISIHP-2S/2U To Remove the ISIHP-2S/2U Card and Drivers in Windows 98 T o remove the ISIHP-2S/2U card: 1. Re-boot your computer . 2. Click S tart , Settings , Control Panel , and then System .
Software/Driver Installation (Windows 95) MultiModemISI Hybrid Series, ISIHP-2S/2U 33 Click Add and the Install New Modem dialog box will appear . Check the box marked Don't detect my modem; I will select it from a list.
Software/Driver Installation (Windows 95) 34 MultiModemISI Hybrid Series, ISIHP-2S/2U 3. The Install New Modem dialog box appears. Insert diskette labeled MultiModem ISI Driver for W indows 95 & Netware AIO and click Have Disk . 4. The Install Fr om Disk dialog box appears.
Software/Driver Installation (Windows 95) MultiModemISI Hybrid Series, ISIHP-2S/2U 35 6. The Install New Modem dialog box appears. Select the port that corresponds to the lowest numbered port of the ISIHP-2S/2U card. Any ports that had been installed before installing the ISIHP-2S/2U card are numbered lower than the ports of the ISIHP-2S/2U card.
Software/Driver Installation (Windows 95) 36 MultiModemISI Hybrid Series, ISIHP-2S/2U 8. After the terminal adapter installs, click Finish to return to the General tab to view COM port assignments (and make changes if necessary).
Software/Driver Installation (Windows 95) MultiModemISI Hybrid Series, ISIHP-2S/2U 37 T o install modems (Windows 95/98): 1. In the General tab, click Add . 2. The Install New Modem dialog box appears. Check the box marked Don't detect my modem; I will select it fr om a list.
Software/Driver Installation 38 MultiModemISI Hybrid Series, ISIHP-2S/2U 3. The Install New Modem dialog box appears. Insert the driver diskette labeled MultiModem ISI Driver for W indows NT . Then click Have Disk . 4. The Install fr om Disk dialog box appears.
Software/Driver Installation MultiModemISI Hybrid Series, ISIHP-2S/2U 39 6. The Install New Modem dialog box appears. Select the numbered port (the fourth highest number) of the ISIHP-2S/2U card. Click Next . The modem installs to the COM port. 7. After the modem installs to the port, click Finish.
Software/Driver Installation 40 MultiModemISI Hybrid Series, ISIHP-2S/2U 8. Return to the General tab to view COM port assignments (and make changes if necessary). 9. Click Add and repeat installation steps 28 to install modems to the last three ports of the ISIHP-2S/2U.
Software/Driver Installation MultiModemISI Hybrid Series, ISIHP-2S/2U 41 Removing the Driver (Windows 95 only) 1. Click Settings , Control Panel , and then double-click Add/ Remove Programs . 2. From the list box, select ISICOM Driver . 3. Click Add/Remove and follow screen instructions.
Software/Driver Installation 42 MultiModemISI Hybrid Series, ISIHP-2S/2U 100, or US National ISDN-1. If you don't know the switch type, get the information from the local phone company . A T command: !CO= SPIDs and DNs ________________________ The T A must be configured with the Service Profile Identifier (SPID).
Software/Driver Installation MultiModemISI Hybrid Series, ISIHP-2S/2U 43 A high DTR (Data T erminal Ready) signal on the serial port indicates that your computer or terminal is ready to communicate with your T A. DTR normally goes high when a communication program starts or is ready to dial.
Software/Driver Installation 44 MultiModemISI Hybrid Series, ISIHP-2S/2U ISDN T A Configuration Utility 1. Before you start the ISDN T A Configuration utility , disconnect the ISIHP-2S/2U by removing the RJ-45 cable from the ISDN jack.
Software/Driver Installation MultiModemISI Hybrid Series, ISIHP-2S/2U 45 10. Click Start , Pr ograms , and then the ISDN T A Configuration Utility icon.
Software/Driver Installation 46 MultiModemISI Hybrid Series, ISIHP-2S/2U 12. The Searching for T A dialog box appears. Click Next . The next dialog box specifies the T A that has been identified.
Software/Driver Installation MultiModemISI Hybrid Series, ISIHP-2S/2U 47 13. The Configuration dialog box appears. If you have questions about choices, click Help . After entering information in each dialog box, click Next . 14.The SPID dialog box appears (North America only).
Software/Driver Installation 48 MultiModemISI Hybrid Series, ISIHP-2S/2U 15. The Data Pr otocol Setup dialog box appears. Referring to your network configuration notes, enter the appropriate information; then click Next . 16. In the Save Configuration dialog box, enter a name to store the configuration.
Software/Driver Installation MultiModemISI Hybrid Series, ISIHP-2S/2U 49 17. T o load the configuration, click Next in the Load Configuration dialog box.
Software/Driver Installation 50 MultiModemISI Hybrid Series, ISIHP-2S/2U ConfigMenu Configuration Utility Use the ConfigMenu configuration utility with computers using DOS or Windows 3.x operating systems. ConfigMenu is installed in the TAs as part of the firmware.
Software/Driver Installation MultiModemISI Hybrid Series, ISIHP-2S/2U 51 ConfigMenu Menus Network Configuration Menu configures network parameters such as switch type, data and voice TEIs, and data and voice MSNs. When you finish, select Save Network Configuration to save your work.
Software/Driver Installation 52 MultiModemISI Hybrid Series, ISIHP-2S/2U NetW are Connect (Novell) Driver Installation Multi-Tech Systems provides AIO drivers for the ISIHP-2S/2U, so it can function with Novell compatible asynchronous applications (e.
Software/Driver Installation MultiModemISI Hybrid Series, ISIHP-2S/2U 53 SCO Open Server 5 Driver Installation The installation utility provided by SCO is called custom . This section provides a brief guide for opening the utility and installing the driver.
Software/Driver Installation 54 MultiModemISI Hybrid Series, ISIHP-2S/2U This section guides you through the Multi-Tech Installation Script for SCO and UNIXWare systems.
Warranty and Service Information MultiModemISI Hybrid Series, ISIHP-2S/2U 55 5. The fifth screen requests you to enter the number of pseudo devices to create for Multi_V iew Utility . Enter the value and press ENTER. Note: Y ou must enter a minimum of 8 for each boar d installed.
Software/Driver Installation 56 MultiModemISI Hybrid Series, ISIHP-2S/2U 8. The Multi_V iew utility initializes the multiple-page capability of terminals with multiple pages of memory . Y ou are asked how many pseudo devices (the total number of pseudo devices you want to make available to the Multi_V iew utility) to create.
Software/Driver Installation MultiModemISI Hybrid Series, ISIHP-2S/2U 57 Multi-T ech s Administrative Utility section in the online manual.) 2. The device database can be modified in two ways: T o create terminal accounts with default settings, type /tcb/bin/ ttys_update .
Software/Driver Installation 58 MultiModemISI Hybrid Series, ISIHP-2S/2U Removing the Driver (SCO Open Server 5) To remove the Multi-Tech Serial Card Driver, enter the configuration utility (e.g., custom for SCO Open Server 5) and follow instructions to remove the entire driver and rebuild the kernel without the ISI driver.
Software/Driver Installation MultiModemISI Hybrid Series, ISIHP-2S/2U 59 Linux Driver Installation T o install the Linux driver: 1. Insert the driver installation diskette. 2. Prepare a temporary installation directory: mkdir isicom 3. Change your current directory to the temporary installation directory: cd isicom 4.
Software/Driver Installation 60 MultiModemISI Hybrid Series, ISIHP-2S/2U Note: A base I/O address of 0, e.g., ISIBaseX=oxo, or omission of these parameters for any car d X, disables that particular car d. Miscellaneous: Device files corresponding to ports on the ISIHP-2S cards are created in the /dev folder .
Software/Driver Installation MultiModemISI Hybrid Series, ISIHP-2S/2U 61 Limited W arranty Multi-T ech Systems, Inc. (MTS) warrants that its products will be free from defects in material or workmanship for a period of two years from the date of purchase, or if proof of purchase is not provided, two years from date of shipment.
Index 62 MultiModemISI Hybrid Series, ISIHP-2S/2U Index A A T commands 41 B Basic Rate Interface (BRI) 4 C ConfigMenu 41 Call Control Configuration Menu 51 Data Protocol Menu 51 Help Menu 51 menus 51 .
in SCO Open Server 5 58 removing driver in W indows NT 32 removing software/driver in W indows 95 28 in W indows 98 32 in W indows NT 26 S S/T interface 1 1 safety warnings 7 SCO Open Server 5 53 serv.
Een belangrijk punt na aankoop van elk apparaat Multi-Tech Systems ISIHP-2S (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Multi-Tech Systems ISIHP-2S heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Multi-Tech Systems ISIHP-2S vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Multi-Tech Systems ISIHP-2S leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Multi-Tech Systems ISIHP-2S krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Multi-Tech Systems ISIHP-2S bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Multi-Tech Systems ISIHP-2S kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Multi-Tech Systems ISIHP-2S . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
