Gebruiksaanwijzing /service van het product FS4004DS van de fabrikant Asante Technologies
Ga naar pagina of 44
FriendlyNet Fast Ethernet Switch FS4004DS/FS4008DS User’ s Manual FRCH1Book Page 1 Thursday, September 25, 1997 11:23 AM.
FRCH1Book Page 2 Thursday, September 25, 1997 11:23 AM.
FriendlyNet Fast Ethernet Switch FS4004DS/FS4008DS User’ s Manual Asanté T echnologies, Inc. 821 Fox Lane San Jose, CA 95131 1.800.662.9686 www .asante.
Copyright Notice Copyright 1997 by Asanté T echnologies, Inc. All rights reserved. No part of this manual, or any associated artwork, software, product design or design concept, may be copied, reprod.
Page iii T able of Contents About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Chapter Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Document Conventions . . . . . . . . . . .
Page iv Connecting Network Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Connecting a PC to the Switch . . . . . . . . . . . . . . . . . . . . . . . 2-8 Connecting a Hub to the Switch . . . . . . . . . . . . . . . . . . . . . . 2-9 Connecting a Hub without an Uplink Port to the Switch .
Page v About This Manual This manual discusses two models of the F r iendlyNet F ast Ethernet Switch: ❏ FS4004DS — four-port 10/100Mps F ast Ether net Switch ❏ FS4008DS — eight-port 10/100Mps Fast Ethernet Switch These models are similar in every respect e xcept for the number of ports.
About This Manual Page vi ❏ Appendix B, “Specifications, ” describes the FriendlyNet Fast Ethernet Switch’ s technical specifications. ❏ Appendix C, “T echnical Support” e xplains how to con- tact Asanté T echnical Support.
Page 1-1 1 Introduction This chapter introduces the F r iendlyNet F ast Ethernet Switch. It also provides an ov er view of F ast Ether net and switc hing technology . FriendlyNet Fast Ethernet Switch Thank you f or purchasing the Asanté FriendlyNet FS4004DS or the FriendlyNet FS4008DS 10/100Mbps F ast Ether net Switch.
Introduction Page 1-2 Features The FriendlyNet FS4004DS and the FS4008DS hav e the following f ea- tures: ❏ Compact size — designed for small to larg e wor kgr oups in space-limited areas; install.
Fast Ethernet and Switching T echnology Page 1-3 Performance Features The FriendlyNet FS4004DS and the FS4008DS hav e the following per- formance f eatures: ❏ Store-and-f orward s witching scheme en.
Introduction Page 1-4 Switching T echnology An Ethernet switch is a device that can dir ect network traffic among sever al Ether net and Fast Ethernet networ ks. A switc h increases networ k capacity and decreases network loading by making it possible for a LAN to be divided into diff erent segments.
Page 2-1 2 Installation This chapter e xplains how to install the FriendlyNet F ast Ethernet Switch. It contains the following sections: ❏ P ackage Contents ❏ FriendlyNet F ast Ether net Switch co.
Installation Page 2-2 Components This section describes the front- and back-panel lay outs of the FS4004DS and FS4008DS. FS4004DS The front panel of the FS4004DS consists of f our 10/100 Mbps por ts, one Uplink port, and LED indicator s. See Figur e 2-1.
Components Page 2-3 FS4008DS The front panel of the FS4008DS consists of eight 10/100 Mbps ports, one Uplink port, and LED indicator s. See Figur e 2-3. Figure 2-3 FriendlyNet FS4008DS front panel The back panel of the FS4008DS consists of a pow er switch, an A C power connector , and a system fan.
Installation Page 2-4 Cabling and V oltage Requirements This section describes the cabling and voltage requir ements of the Switch. Cabling Requirements 100Base-TX requires data-g rade (Categor y 5) UTP (unshielded twisted- pair) cable.
Mounting Configurations Page 2-5 Mounting Configurations This section describes how to mount the Switch on a desktop or a wall. It also e xplains how to install the Switch in an equipment r ack. Desktop Mounting T o mount the Switch on a desktop or shelf: 1 Attach the f our r ubber feet (supplied) to the bot- tom of each corner on the Switch.
Installation Page 2-6 Wall Mounting the FS4004DS The FS4004DS comes with a wall-mount kit. ▲ Important! The FS4008DS cannot be mounted on a wall. T o mount the FS4004DS on a wall, consider the f oll.
Mounting Configurations Page 2-7 Rack Mounting the FS4008DS The FS4008DS comes with a rack-mounting kit. ▲ Important! The FS4004DS cannot be installed in an equipment rack. The FS4008DS can be mounted in a standard 19-inc h equipment rack. This rack can be placed in a wiring closet with other equipment.
Installation Page 2-8 Connecting Network Devices Befor e you connect networ k devices to the Switch, review the f ollow- ing guidelines: ✔ Make sure the networ k cable length is less than 100 meters . ✔ Use a straight-through twisted pair cable or a cross-over cable.
Connecting Network Devices Page 2-9 Connecting a Hub to the Switch ❏ Use a two-pair Categ or y 5 UTP straight-through cable with RJ-45 connectors. ❏ Connect the hub’ s uplink port to any of the Switc h’ s ports (1 – 4 for the FS4004DS or 1 – 8 f or the FS4008DS).
Installation Page 2-10 Connecting a Hub without an Uplink Port to the Switch If a hub is not equipped with an uplink port, connection can be made using either a straight-through cable or a cross-o ver cable, as outlined below .
Connecting Network Devices Page 2-11 Connecting the Switch to Another Switch or Network Device The Switch can be connected to another s witch or to other networ k devices (such as a router , br idg e, etc.) via a two-pair Category 5 UTP straight-through or cross-o ver cable.
Installation Page 2-12 Powering on the Switch This section describes how to power on the FS4004DS and the FS4008DS Fast Ethernet Switch. FS4004DS The FS4004DS’ s may be turned on with or without LAN segment cables connected.
Page 3-1 3 LED Indicators This chapter e xplains how to interpret the front-panel LED indicators on the FriendlyNet F ast Ether net Switch. The indicators are discussed in the following sections.
LED Indicators Page 3-2 The front-panel LEDs f or the FS4004DS and the FS4008DS are shown in Figure 3-1 and F igure 3-2, respectiv ely . Figure 3-1 FS4004DS LEDs Figure 3-2 FS4008DS LEDs LED Indicators for Power Connections After the Switch is turned on, the LED indicators should respond as follo ws: ❏ All LED indicators blink momentarily .
LED Indicators for Port Connections Page 3-3 LED Indicators for Port Connections Link/Activity LED The gr een Link/Activity LED indicates if there is a device detected on the other end of the port and if there is traffic on the por t. T able 3-1 descr ibes the possible status indications of the Link/Activity LEDs.
LED Indicators Page 3-4 FDX/Col LED The FDX/Col (full duple x/collision) LED indicates when a port is in full duplex (FDX) mode, or when two or more stations on the specific net- wor k segment attempt to transmit packets simultaneously , causing a packet collision.
LED Indicators for Switch Connections Page 3-5 LED Indicators for Switch Connections PC to Switch Connection The LED indicators for PC connection are dependent on the PC’ s LAN card capabilities.
LED Indicators Page 3-6 Switch to Switch or other Network Devices Connection T able 3-4 describes the possible status indications of the Switch to switc h or other network devices connection.
Page A-1 A T roubleshooting T able A-1 describes how to troubleshoot prob lems with your netw ork and/or the Switch by monitoring the Switch’ s LEDs. T able A-1 T roubleshooting Problem Action Power LED is off ✔ Make sure the power adapter is connected to the power outlet and is properly inserted into the power connector on the switch.
T roubleshooting Page A-2 Problem Action Link LED is off ✔ Make sure the switch is powered on. ✔ Make sure the device on the other end is pow- ered on. ✔ Make sure the proper cabling is used between the device and the Switch (refer to the cable guidelines specified in Chapter 2).
Page B-1 B Specifications FS4004DS and FS4008DS Specifications Standards ❏ IEEE 802.3 10Base-T Ethernet ❏ IEEE 802.3u 100Base-TX Fast Ethernet ❏ IEEE 802.
Specifications Page B-2 Media Interface Exchange MDI-II RJ-45 shared with port 1x Physical and Environmental AC Inputs 100 - 240 V AC, 50/60 Hz (internal universal power supply) Power Consumption 40 .
Performance Specifications Page B-3 Performance T ransmission Method Store-and-forward RAM Buffer FS4004DS: 4MB per device FS4008DS: 8MB per device Filtering Address T able 8K entries per device Pack.
FRCH1Book Page 4 Thursday, September 25, 1997 11:23 AM.
Page C-1 C T echnical Support Contacting T echnical Support T o contact Asanté T ec hnical Suppor t: T elephone (800) 622-7464 Fax (408) 432-6018 Fax-Bac k (800) 741-8607 Internet Mail support@asante.
FRCH1Book Page 2 Thursday, September 25, 1997 11:23 AM.
Index-i Index Numerics 100Base-TX, cables supported B-1 100Mbps LED 3-3 10Base-T, cables supported B-1 10Mbps LED 3-3 A about this manual v AC inputs B-2 power connector 2-3 activity LED 3-3 address entr y table, MA C 1-3 table, filtering B-3 assistance.
Index-ii FS4008DS (continued) mounting options 2-5 overview 1-1 performance features 1-3 power, connecting 2-12 specifications B-1 full duplex LED 3-4 troubleshooting A-2 H help. See technical support or troubleshooting hub connecting to switch 2-9 , 2-10 to switch, LED 3-5 humidity B-2 I IEEE 802.
Index-iii P package contents 2-1 packet buffer 1-3 filtering/forwarding r ate B-3 PC (personal computer) connecting to switch 2-8 to switch, LED 3-5 performance featur es 1-3 troubleshooting A-2 pers.
FRCH1Book Page iv Thursday, September 25, 1997 11:23 AM.
FRCH1Book Page 1 Thursday, September 25, 1997 11:23 AM.
ASANTÉ TECHNOLOGIES, INC., 821 FO X LANE, SAN JOSE, CA 95131 PHONE: 408.435.8388, 800.662.9686 • F AX: 408.432.7511 • e-mail address: sales@asante.com • W orld Wide W eb site: http://www .asante.com ©1997 Asanté T echnologies Inc., Asanté is a trademark of Asanté T echnologies, Inc.
Een belangrijk punt na aankoop van elk apparaat Asante Technologies FS4004DS (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Asante Technologies FS4004DS heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Asante Technologies FS4004DS vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Asante Technologies FS4004DS leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Asante Technologies FS4004DS krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Asante Technologies FS4004DS bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Asante Technologies FS4004DS kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Asante Technologies FS4004DS . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
