Gebruiksaanwijzing /service van het product IC36240 Series van de fabrikant Asante Technologies
Ga naar pagina of 42
IntraCore ® IC36240 Series Layer 2+ Gigabit Ethernet Switch Setup Guide.
IntraCore IC36240 Layer 2+ Gigabit Ethernet Switch Setup Guide Asante Technologies, Inc. 2223 Oakland Road San Jose, CA 95131 USA SALES 800-662-9686 Home/Office Solutions 800-303-9121 Enterpris e Solutions 408-435-8388 TECHNICAL SUPPORT 801-566-8991: W orldwide 801-566-3787: F ax www.
Table of Contents Table of Conten ts ........................................................................................................................................................... 3 Chapter 1: Introduc tion ...............................
3.2 Connecting to a PC ......................................................................................................... ................................... 17 3.3 Passwords and Priv ileges Co mmands ...........................................
4.8.5 Scrolling Down a Line or a Scr een ........................................................................................ ....................... 33 4.8.6 Redisplaying the Current Comma nd Line .................................................
Chapter 1: Introduction The IntraCore IC36240 24-por t Layer 2+ Managed Giga bit Switch is a high-performance net work switch used to reduce network congestion a nd application response times. The 24-port IntraCore IC36240 multi-protoc ol switch supports Layer 2+ and Giga bit Ethernet switching.
1.2 Package Contents The following items are included in the s witch’s package: • Swi tch • AC power cord • USB cable for management console port • RS232 null-modem cable for manageme nt con.
1.3.1 LEDs The IC36240 front panel LE D display allo ws you to monitor the status of the switch. The IC36240 has one po wer LED indicator, one (optional) ext e rnal power LED and one f an LED. There are also LED indicators for each of the 24 ports. Refer to the following tabl e for LED information.
1.4 Management and Configuration The switch is managed usin g Command Line Interface (CLI ) in order to a ccess several different command modes. Entering a question mark (?) at each command mode’s prompt provides a list of commands.
Chapter 2: Hardware Installation and Setup Use the following guidelines to easi ly install the switch, ens uring that it ha s the proper power supply and environment. 2.1 Installation Overview Follow these steps to install the IntraCore IC36240 s witch: 1.
2.1.2 Recommended Installation Tools You need the following ad ditional tools and equ ipment to install the switch into an equipment rack: • Flat head screwdriver • Phillips head screwdriver • Antistatic mat or foam 2.1.3 Power Requirements The electrical outlet should be properl y grounded, locat ed near the switch and be easil y accessible.
5. Place the switch in the equipment rack. 6. Secure the switch by securing its mounting br acke ts onto the equipment rack with the appropriate screws (supplied). Important: Make sure the switch is supported until all the mounting scre ws for each bracket are secured to the equipment rack.
To verify the primary power status, use the Switch# show system command. Under System Informat ion, you see the power unit status. System Information ------------------ System up for: 000day(s), 01hr(s), 46min(s), 54sec(s) PROM Image Version/Date: 1.00C/Nov 11 2004 17:03:04 DRAM Size: 64.
Important: The switch must be located within 100 meters of its attached 10Bas eT or 100BaseTX dev ices. Use the following guidelines to determi ne the cabling requirements for the network devices: •.
• 1000BaseLH GBIC: Cables wit h SC-type fiber connectors; 10µ sing le-mode fiber media up to 20 km (65,617') • 1000BaseLX Long H aul GBIC: Cables with SC-type fiber connectors; 10µ single-m.
Chapter 3: Initial Software Setup Configure the switch by connecting directly to it th rough a console (out-of-band managem ent), running a terminal emulation program, such as HyperT erminal or by using telnet. 3.1 Connecting to a Console To connect the switch to a console or computer , set up the system in the following manner: 1.
e. Press the Configuration button from the Connect To window. e f. Set the data rate to 9600 Baud. g. Set data format to 8 data bits, 1 stop bit and no parit y. h. Set flow control to NONE. f g h Now that terminal is set up correctly, power on the sw itch.
3.3 Passwords and Privileges Commands The switch has not default pass word, which allows any one on the net work access to various privilege levels. T o prevent unauthorized changes to the switch’s configuration, you sho uld set an enable password for access to s witch management.
3.3.3 Password To specify a password on a line, use the password command in line confi guration mode. Use the no form of this command to remove the password.
3.4 Login Security Two methods are available o n the IntraCore IC36240 to co nfigur e an authentication quer y process for better login security: the username command for the g lobal configuration mode an d password and login commands from the line configuration mode.
5. Type ip address and the new addr ess. The following screen appears: Switch> enable Switch# configure Switch(config)# ip address 192.168.123.254/24 Switch(config)# end Switch# show ip Dhcp Client Enabled ..........: No IP Address ................
Chapter 4: Understanding the Command Line Interface (CLI) The switch utilizes Command Lin e Interface (CLI) to pr ovide access to seve ral different command modes. Each command mode provides a group of related commands. After logging into the system, you are autom atically in the user top (user E XEC) mode .
To list the commands available in user top m ode, enter a question mark (?). Use a space and a questi on mark (?) after entering a command to see all the options for that particular command. Command Purpose ? Lists the user EXEC commands. show ? Lists all the options avail able for the given command.
In general, the top (privileged) commands allow you to change terminal set tings on a temporary b asis, perform basic tests, and list system information. To list the commands av ailable in top mo de, enter a question mark (?) at the prompt, as shown in the following example.
To exit global config uration command mode and return to privile ged EXEC mode, use on e of the following commands: Command Purpose exit end Ctrl-Z Exits global configuration mo de and returns to privileged EXEC mode.
4.3.1 Interface Configuration Mode Many features are enabled on a per-interface basis. Interface configuration commands m odify the operation of an interface such as an Ethernet or serial port. In terface configuration commands al ways follow an interface global configuration command, which defin es the interface type as Ethernet.
In the following example, the switch shows the multiple Spanni ng Trees (MST) command. Switch(config)# spanning-tree mst configuration Switch(config-mst)# ? end End current mode and change to enable m.
To get help specific to a command mode, a command, a keyword, or an argument, perform one of the following commands: Command Purpose Help Obtain a brief description of the help system in an y command mode. ? List all commands available for a particu lar command mode.
Switch# configure ? configure Enter configuration mode Note that in the example below, if you e nter the ip comman d followed by the Return Key or Enter, the system returns the prompt that the command is incomplete. Switch# ip % Command incomplete. Switch# Generally, uppercase letters represent variables.
4.6 Using CLI Command History The CLI user interface provides a histor y or record of co mmands that you have e ntered. This feature is particularl y useful for recalling long or co mplex commands or entries, including access lists.
4.8.1 Moving Around on the Command Line Use the following keystrokes to move the cur sor around on the command line in order to make corrections or changes: Keystrokes Purpo se Press Ctrl-B or the left arrow. Move the cursor back one character. Press Ctrl-F or the right arrow.
4.8.3 Editing Command Lines That Wrap The enhanced editi ng feature provides a wraparound for comm ands that extend beyond a sing le line on the screen.
When you have completed th e entry, press Ctrl-A to check the complete syntax before pr essing Enter to execute the command. The dollar sign ($) appears at the end of the l ine to indicate that the line has been scrolled to the right: Switch(config)# access-list 101 permit icmp 192.
4.8.7 Transposing Mistyped Character s If you have mistyped a command e ntry, you can transpose the mist yped characters by using the follo wing command: Keystrokes Purpo se Press Ctrl-T . Transpose the character to the left of the cursor with the character located at the cursor.
Appendix A: Basic Troubleshooting In the unlikely event that the s witch does not operate properly, follo w the troubleshooting tips below. If more help is needed, contact Asante’s technical support at www.asante.com/support . Problem Possible Solutions The Power LED is not lit.
Appendix B: Specifications The sections below list the feat ures and product specificati ons for the IntraCore IC36240 switch. Connectors: 24 RJ-45 auto-MDI/MDIX Ports 24 10/100/1000BaseT ports that h.
Security User password, SNMP access filter, port security (MAC address filter with notification), 802.1x (port-based, L2/L4 ACL, RADIUS, TACACS+ Management Male DB9 RS-232 DTE (auto bau d to 115k), US.
Appendix C: FCC Complian ce and Warranty Statements C.1 FCC Compliance Statement This equipment has bee n tested and found to comply with t he limits for a Class A digital devic e, pursuant to part 15 of the FCC Rules.
C.3 IntraCare Warranty Statement Products: IntraCore IC36240 Duration: 3 years Advanced Warrant y United States: Second Business Day Replacement: Other countries: See your local distributor or resell er 1.
Appendix D: Online Warranty Registration Please register this product online at http:// www.asante.com/support/supRegistration.asp or by filling out and mailin g the card below.
Index Cabling consol e ................................................................. 16 Ethernet ................................................................ 14 procedur es............................................................ 13 CLI advanced f eatures .
Featur es ..................................................................... 6 editing ................................................................... 30 Help ? 28 context sens itive ................................................... 28 Installation emergency powe r supply .
Een belangrijk punt na aankoop van elk apparaat Asante Technologies IC36240 Series (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Asante Technologies IC36240 Series heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Asante Technologies IC36240 Series vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Asante Technologies IC36240 Series leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Asante Technologies IC36240 Series krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Asante Technologies IC36240 Series bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Asante Technologies IC36240 Series kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Asante Technologies IC36240 Series . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
