Gebruiksaanwijzing /service van het product FP-PWM-520 van de fabrikant National Instruments
Ga naar pagina of 19
FIELDPOINT ™ OPERATING INSTRUCTIONS AND SPECIFICATIONS FP-PWM-520 and cFP-PWM-520 Eight-Channel, 5 V or 10–30 V PWM Output Module These operating instructions desc ribe ho w to install and use the National Instruments FP -PWM-520 and cFP- PWM-520 pulse-width modulation modules (referred to inclusiv ely as the [c]FP-PWM-520).
FP-PWM-520 and cFP-PWM-520 2 ni.com Installing the FP-PWM-520 The FP-PWM-520 mounts on a Fi eldPoint terminal base (FP-TB- x ), which provides operating power to the module. Installing the FP-PWM-520 onto a po wered terminal base does not disrupt the operation of the bank.
© National Instruments Corp. 3 FP-PWM-520 and cFP-PWM-520 Installing the cFP-PWM-520 The cFP-PWM-520 mounts on a Compact FieldPoint backplane (cFP-BP- x or cFP-180 x ), which pro vides operating po wer to the module. Installing th e cFP-PWM-520 onto a powered backplane does not disrupt the operation of the bank.
FP-PWM-520 and cFP-PWM-520 4 ni.com Wiring the [c]FP-PWM-520 The FP-TB- x terminal base ha s connections for each of the eight output channels and for an exte rnal power supply to po wer the output channels and field de vices. The cFP-CB- x connector block provides th e same connections.
© National Instruments Corp. 5 FP-PWM-520 and cFP-PWM-520 Install a 2 A maximum, fast-acti ng fuse between the external power supply and the V SUP terminal on each cha nnel. Install a 1 A maximum, fast-acting fuse suitable for the load at the V OUT terminal.
FP-PWM-520 and cFP-PWM-520 6 ni.com In the ON state, the ef fecti ve resistance between V OUT and V SU P causes a v oltage drop between th e external supply v oltage and the output voltage.
© National Instruments Corp. 7 FP-PWM-520 and cFP-PWM-520 • Disconnect the external po wer supply from the [c]FP-PWM-520. • Remov e the [c]FP-PWM-520 from the terminal base or backplane. • Po wer off the network module connected to the [c]FP-PWM-520.
FP-PWM-520 and cFP-PWM-520 8 ni.com Configuring the Output Channels A [c]FP-PWM-520 output channel uses period and duty-cycle settings to determine when the cha nnel is on or of f. T o configure the period, complete the fol lowing steps in Mea surement & Automation Explorer (MAX): 1.
© National Instruments Corp. 9 FP-PWM-520 and cFP-PWM-520 [c]FP-PWM-520, it sends initial conf igurati on information to the [c]FP-PWM-520. After the [c]FP-PWM-520 recei v es this initial information, the green READY indicator lights and the module is in normal operating mode.
FP-PWM-520 and cFP-PWM-520 10 ni.com Even though the [c]FP-PWM- 520 is designed to handle applications with hazardous potent ials, follo w these guidelines to ensure a safe total system: • There is no isolation between channels on the [c]FP-PWM- 520 .
© National Instruments Corp. 1 1 FP-PWM-520 and cFP-PWM-520 Safety Guidelines for Hazardous Locations The cFP -PWM- 520 is suitable fo r use in Class I, Di vision 2, Groups A, B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nC IIC T4 and Ex nC IIC T4 hazardous locations; and nonhazardous locations only .
FP-PWM-520 and cFP-PWM-520 12 ni.com Specifications The follo wing specif ications are typical for a range of – 40 to 70 °C unless otherwise noted. Output Characteristics Number of channels ............ ........... ... 8 Output type ...............
© National Instruments Corp. 1 3 FP-PWM-520 and cFP-PWM-520 Guaranteed trip current Re vision E and later modules ..... 12.5 A Re vision D and earlier modules ...... ........... ......... ............ 20 A T rip time Re vision E and later modules ...
FP-PWM-520 and cFP-PWM-520 14 ni.com Mechanical Dimensions Figure 5 sho ws the mechanical dimensions of the FP-PWM-520 installed on a termin al base. If you are using the cFP-PWM-520, refer to your Compact FieldPo int controller user manual for the dimensions and cabling clearance require ments of the Compact FieldPoint system.
© National Instruments Corp. 1 5 FP-PWM-520 and cFP-PWM-520 Shock and Vibration These specifications apply only to the cFP-PWM-520. NI recommends Compact FieldPoi nt if your application is subject to shock and vibration. Operating vibration, random (IEC 60068-2-64).
FP-PWM-520 and cFP-PWM-520 16 ni.com Electromagnetic Compatibility This product is designed to meet the requirements of the following standards of EMC for electrical equipment for measurement, control.
© National Instruments Corp. 1 7 FP-PWM-520 and cFP-PWM-520 Waste Electrical and Electronic Equipment (WEEE) EU Customers At the end of their lif e cycle, all products must be sent to a WEEE re c ycling center . F or more information about WEEE recycling centers and National Instruments WEEE init iativ es, visit ni.
FP-PWM-520 and cFP-PWM-520 18 ni.com Where to Go for Support For more information about settin g up the FieldPoint system, refer to these National Instruments documents: • FieldPoint network module user manual • Other FieldPo int I/O m odule operating instructions • FieldPoint terminal base and connector block operating instructions Go to ni.
© 2002–2007 Nati onal Instruments Corp. All rights reserved . 373357C-01 Dec07 National Instruments, NI, n i.com, and LabVIEW are trademarks of Na tional Instruments Corporation. Refer to the Terms of Use section on ni.com/legal for more information about National In struments trademarks.
Een belangrijk punt na aankoop van elk apparaat National Instruments FP-PWM-520 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen National Instruments FP-PWM-520 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens National Instruments FP-PWM-520 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding National Instruments FP-PWM-520 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over National Instruments FP-PWM-520 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van National Instruments FP-PWM-520 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de National Instruments FP-PWM-520 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met National Instruments FP-PWM-520 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
