Gebruiksaanwijzing /service van het product LT10 van de fabrikant NEC
Ga naar pagina of 36
Portable Projector L T10 User s Manual.
FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- nglish Table of Contents T able of Contents ....................................................................................... 1 Important Information ............................................................................... 2 Precautions .
- nglish Important Information Precautions Follow all warnings, precautions and maintenance as recom- mended in this user’s guide to maximize the life of your unit. Warning- Do not look into the projector’s lens when the lamp is on. The bright light may hurt your eyes.
! - nglish Do: Turn off the product before cleaning. Use a soft cloth moistened with mild detergent to clean the display housing. Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Don’t: Block the slots and openings on the unit provided for ventilation.
" - nglish Introduction This product is an XGA single chip 0.7” DLP TM projector. Outstanding features include: True XGA, 1024 x 768 addressable pixels 2.
# - nglish Power Cord S-Video Cable VGA Cable Remote Control Battery User’s Guide on CD-ROM Introduction Composite Video Cable Projector with lens cap What's in the Box? This projector comes with all the items shown below. Check to make sure your unit is complete.
$ - nglish Introduction Main Unit Product Overview 1. Focus Ring 2 . Zoom Ring 3. Adjustable Tilt Foot Button 4 . Zoom Lens 5 . Remote Control Receiver 6.
% - nglish Control Panel Introduction 1. Power Indicator 2. Status Indicator 3. On/Standby 4. Source 5 . Directional Select and Enter Keys 6 . Keystone Correction 7 . Menu (On/Off) 3 4 6 5 Terminal Panel 1. AC Inlet 2 PC Analog Signal/HDTV/Component Video Connector 3 .
& - nglish Remote Control Introduction 2 11 7 6 10 3 8 9 1 . Transmit Indicator Light 2 . Power 3 . Source 4 . Keystone Correction 5 . Zoom In/Zoom Out 6 .
' - nglish 1. Power Cord 2. VGA Cable 3. S-Video Cable 4. Composite Video Cable Connecting the Projector To ensure the projector works well with your computer, please set the display mode of your graphics card is less than or equal to 1024 X 768 resolution.
- nglish Installation Lens cap On/Standby 1 2 Powering On the Projector 1. Remove the lens cap. n 2. Ensure that the power cord and signal cable are securely connected. 3. Turn on the lamp by pressing “On/Standby” button on the control panel.
- nglish Powering Off the Projector 1. Press the “Power” button to turn off the projector lamp. 2. After pressing the “Power” button, you will see a message “Power off the lamp?” on the on-screen display. Press the “Power” button again to confirm.
- nglish Installation Adjusting the Projected Image Adjusting the Projector Height Tilt Adjusted wheel Adjustable Tilt Foot 1 2 3 Adjustable Tilt Foot Button The projector is equipped with an adjustable tilt foot foot for adjusting the projector height.
! - nglish . x a M ) m c 4 . 1 8 ( " 1 . 2 3 ) m c 6 . 3 0 2 ( " 2 . 0 8 ) m c 3 . 9 3 3 ( " 6 . 3 3 1 ) m c 2 . 7 0 4 ( " 3 . 0 6 1 ) m c 0 . 3 4 5 ( " 8 . 3 1 2 ) m c 7 . 8 7 6 ( " 2 . 7 6 2 . n i M) m c 0 . 0 7 ( " 6 .
" - nglish User Controls Remote Control Control Panel Control Panel & Remote Control There are two ways for you to control the functions: Remote Control and Control Panel. Using the Control Panel On/Standby Refer to the “Powering On/Off the Projector” section on pages 10-11.
# - nglish Using the Remote Control Power Refer to the “Powering On/Off the Projector” section on pages 10-11. Source Press “Source” to choose RGB, Component-p, Component-i, S-Video, Composite Video and HDTV sources. AUTO ADJ. (Auto Adjust) When “AUTO ADJ.
$ - nglish The Projector has multilingual On Screen menus that are multilingual allowing you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSM menu, press “Menu” on the Remote Control or Control Panel.
% - nglish Language Language You can display the multilingual OSM menu . Use the or key to select your prefered language. Press “Menu” to finalize the selection.
& - nglish User Controls All Images Brightness Adjusting the brightness of the image. Press the to darken image. Press the to lighten the image. Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture.
' - nglish All Images Aspect Ratio Selects the desired aspect ratio. Reset This Menu Choose “Yes” to return the display parameters on this menu to their factory default settings.
- nglish User Controls Computer Image Auto Adjust The projector automatically adjusts clock, phase, horizontal and vertical. With most signal sources, Auto Adjust provides the best results. Clock “Clock”changes the display data frequency to match the frequency of your computer’s graphic card.
- nglish Video Image Video Mode Color Adjusts a video image from black and white to fully saturated color. Press the to decrease the amount of color in the image. Press the to increase the amount of color in the image. Sharpness Adjusts the sharpness of the image.
- nglish User Controls Menu Location Choose the Menu location on the display screen. Orientation Front-Desktop The factory default setting. Rear-Desktop When you select this function, the projector reverses the image so you can project behind a translucent screen.
! - nglish Setup Computer / Video Mode User Controls Factory Default Choose “Yes” to return the display parameters (except for Lamp Hours) on all menus to their factory default settings.
" - nglish PIP PIP Choose “On” to turn the PIP screen on. PIP Location Choose the PIP screen position on the display screen. PIP Switch Source Choose the input source of the projector on the PIP screen. Reset This Menu Choose “Yes” to return the display parameters on this menu to their factory default settings.
# - nglish Appendices Problem: No image appears on screen. Ensure all the cables and power connections are correctly and securely connected as described in the “Installation” section. Ensure the pins of connectors are not crooked or broken.
$ - nglish Appendices 4. Follow above steps 1-2. Click on the “Advanced Properties” button. 5. Select the “Change” button under the “Monitor” tab . 6. Click on “Show all devices”. Then select “Standard monitor types” under the “Manufactures” box ; choose the resolution mode you need under the “Models” box.
% - nglish Problem: Image is out of focus Adjusts the Focus Ring on the projector lens. Refer to page 13. Make sure the projection screen is between the required distance 3.94 to 32.81 feet (1.20 to 10.00 meters) from the projector. Problem: The image is outstretched when displaying 16:9 DVD.
& - nglish Appendices Changing the lamp The projector will detect the lamp life itself. It will show you a warning message “The Lamp has been in use for over 2000 hours. You should purchase a spare bulb.” When you see this message, please change the lamp as soon as possible.
' - nglish Specifications Light Valve - Single Chip DLP TM Technology by Texas Instruments Lamp - 120W User Replaceable P-VIP Lamp Number of Pixels - 1024 pixels(H) X 768 lines(V) Displayable Color - 16.7M colors Projection Lens - F/2.8~3.1 f=25.
! - nglish A G V A S E V 0 5 3 X 0 4 6 0 7 5 . 1 3 A G V A S E V 0 5 3 X 0 4 6 5 8 9 . 7 3 A G V A S E V 0 0 4 X 0 4 6 5 8 9 . 7 3 A G V A S E V 0 8 4 X 0 4 6 0 6 5 . 1 3 A G V A S E V 0 8 4 X 0 4 6 2 7 9 . 7 3 A G V A S E V 0 8 4 X 0 4 6 5 7 5 . 7 3 A G V A S E V 0 8 4 X 0 4 6 5 8 3 .
A-1 T ravelCa r e Guide T ravelCare - a service for international travelers This product is eligible f or "T rav elCare", NEC's unique international war- r anty . Please note that T rav elCare cov erage diff ers in part from coverage un- der the warr anty included with the product.
A-2 In Asia and Middle East NEC Viewtechnology , Ltd. Address: 686-1, Nishioi, Oi-Machi, Ashigarakami-Gun, Kanagaw a 258-0017, Japan T elephone: +81 465 85 2369 F ax Line: +81 465 85 2393 Email Address: support_pjweb@nevt.nec.co .jp WEB Address: http://www .
A-3 TO : NEC or NEC’ s A uthorized Service Station: FM: (Company & Name with signature) Dear Sir (s), I would lik e to apply your T ravelCare Service Program based on attached registration and q.
A-4 Condition of your T ravelCare Service Pr ogram Enduser is requested to understand f ollowing conditions of T ravelCare Service Program and complete the necessary information on the appli- cation sheet. 1. Service Options: There are 3 types of "Service" availab le.
Een belangrijk punt na aankoop van elk apparaat NEC LT10 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen NEC LT10 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens NEC LT10 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding NEC LT10 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over NEC LT10 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van NEC LT10 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de NEC LT10 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met NEC LT10 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
