Gebruiksaanwijzing /service van het product CM8SW van de fabrikant Niles
Ga naar pagina of 24
B LENDING H IGH F IDELITY AND A R CHITE C TURE ® INST ALLA TION & OPERA TION GUIDE ® INST ALLA TION & OPERA TION GUIDE SUBWOOFER CM 8 S W.
Congratulations! Thank you for choosing a Niles ceiling mount loudspeaker. With proper installation and operation, you'll enjoy years of trouble-free use. The CM8SW is a ceiling mount subwoofer uniquely designed to provide unobtrusive low frequency augmentation.
F eat ur es and Benefit s TCC Speaker Cone The Niles CM8SW is a high-performance passive subwoofer that compliments the entire Niles ceiling mount loudspeaker line.
Infinite Baffle Design The CM8SW is designed for optimum low frequency reproduction in traditional ceil- ing environments and varying air volumes. It does not require a special enclosure to provide high performance.
Ho w Man y Sub w oo f er s? 4 Ho w Man y Sub w oof er s? For most applications a single CM8SW is appropriate. However, in large rooms, high performance listening rooms or in home theaters, an array of two or more CM8SW will deliver astounding results.
Connections Single Stereo Subwoofer A four conductor (Left+, Left-, Right+ and Right- ) wire 16 gauge or larger (see side- bar on speaker wire gauge) is run from the amplifier location to the local volume control (See Figure 4) . From the local volume control the four conductor cable is run to the CM8SW and connected to the Input connectors.
6 Connections the left and right speakers simultaneously. Additionally, the crossovers are now con- nected so that the crossover switches can be adjusted to your requirements. You must adjust the crossovers on each speaker with this hook-up. Optionally, a jumper of wire may be connected between the L+ and the R+; and between the L- and the R-.
Impedance With One or Two Subwoofers When one or two CM8SW subwoofers are connected to the satellite speakers, the overall system impedance to the amplifier lowers. System Impedance in Ohms ( Ω ) One or Two Subwoofers 8 Ω Sats 4 Ω Sats 1 Sub 4 Ω 2.
Using Speaker Selectors With Standard Volume Controls In multi-room systems with standard vol- ume controls any Niles speaker selector will maintain a four ohm load if you leave one set of room outputs unused for every speaker system with an impedance of less than four ohms (such as a CM8SW con- nected to a pair of four ohm satellite speakers).
T r eat ment & Placemen t Typically, sheetrock encloses the sub- woofer in most installations. Sheetrock has a fairly loud resonant “twang” compared to the rigid non-resonant enclosures of most floor standing subwoofers.
Inst allation F undament als Introduction If you have doubts about whether you are capable of installing a ceiling mount speak- er, consult a Niles dealer or professional installer. They have special tools, tech- niques, and experience to make the impos- sible possible.
1 1 Ins t allation F undamen t als bottom of the ceiling joists. Then work backward so that you can always see the holes you have already drilled. Paying care- ful attention to this will save you a lot of time later on! Pulling the Cable Pull the cable in sections (from the stereo to the volume control, from the volume con- trol to the speaker).
switch or receptacle, and shining a penlight into the wall. If you have access to an attic or base- ment space you can quickly see which part of the wall space is free of obstructions (See Figure 12) .
In traditional wood ceiling joist/ drywall construction you should first cut the hole for the speaker and utilize the large hole to auger holes across the ceiling (through the ceiling joists) for as far as your drill bit will take you.
Inst allation in Ne w Constr uction Stage One: Before Drywall is Hung Insulating the Wall Cavity. If feasible, fill the wall cavity with insulation at this point . Mounting The CM8 Series New Construction Bracket The hole saving bracket enables a faster and cleaner final installation of the speaker.
Inst allati on in Existing Cons tru ction IMPORTANT: Before you cut into any wall, review the sections on running wire and speaker placement. 1. When determining the location of the speaker cutout keep in mind that the mounting dogs will extend 3/4” beyond the cutout.
F inal Inst allation in Ne w or Existing Cons tru ction 1. If it is possible to lay a batt of insulation into the ceiling cavity, do so. Remember to use equal amounts of insulation for each speaker. 2. Separate the speaker wire so that at least two inches of each conductor are free.
Painting the Speakers All models may be painted. The plastic will readily accept most paints. The speakers must be masked prior to painting them. The inside circular portion of the hole template can be used as a paint mask. Remove the outside portion of the template by gently pulling along the perforation.
Oper ation Congratulations A concealed CM8SW subwoofer installation frees you to use your tone controls, play the sys - tem loudly and enjoy deep extended bass, even if your satellite speakers are small. When used with satellite speakers that have substantial bass of their own, the CM8SW tightens the deep tones and augments the bass musically.
Specifications CM8SW Driver Complement 8” dual voice-coil injection molded TCC (Talc, carbon and ceramic-filled) woofer with butyl rubber surround Design Principle Infinite baffle for large and vary.
DETACH HERE AND RETURN TO: Niles Audio Corporation, Inc. Warranty Registration Dept. P .O. Box 160818 Miami, Florida 3 3 1 16 - 0818 M o d e l P u r c h a s e d __________________ ____________ _ ____ .
PLEASE FILL OUT THE W ARRANTY REGISTRA TION C ARD ON THE REVERSE SIDE, DET A CH, AND MAIL T O: Niles A udio Corpor ation W arr anty Registr ation Dept.
L imited W arr an ty Niles Audio Corporation ("NILES") warrants its loudspeaker products to the original purchaser to be free of manufacturing defects in material and workmanship for a period of five years from date of purchase. This Warranty is subject to the following additional conditions and limitations.
© 2004 Niles Audio Corporation. All Rights Reserved. Niles, the Niles logo, and Blending High Fidelity and Architecture are registered trademarks of Niles Audio Corporation. MicroPerf is a trademark of Niles Audio Corporation. All other trademarks are the property of their respective owners.
Een belangrijk punt na aankoop van elk apparaat Niles Niles CM8SW (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Niles Niles CM8SW heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Niles Niles CM8SW vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Niles Niles CM8SW leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Niles Niles CM8SW krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Niles Niles CM8SW bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Niles Niles CM8SW kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Niles Niles CM8SW . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
