Gebruiksaanwijzing /service van het product 302403-G van de fabrikant Nortel Networks
Ga naar pagina of 32
Part No . 302403- G July 20 01 4401 Gr eat Ame rica Parkwa y Santa Clara, CA 95054 *302403-G* Installing Media Dependent Adapters (MDAs).
Copyright © 2001 Nortel Networks All rights re s e rv e d. July 2001 . The information i n this document is subject to change without notice. The statements, configuration s, technical data, and recom mendations in this docum ent are believed to be accurate and reliable, but are p resented without express or implied war ranty .
1 Product Safety Meets requirements of: CSA 22.2 No. 950-M95/UL1950, 3rd ed. EN60950: 1992 /A1:1993 /A2:1993 /A3: 1995 /A4: 199721CFR, Chapter I EN60825-1:1994 /A11:1996 Caution: Only qualified technicians should install this equipme nt. Place all printed ci rcuit boards o n an antista tic mat until you are read y to insta ll them.
2 W arning: Ave rtissement: L ’é quipem ent à fibre opt ique peu t é mettre des rayons laser ou infrarouges qui ri sq uent d ’ ent ra î ner d es l é sions oculaires. Ne jamais regard er dan s le port d ’ un connec teur ou d ’ un c â ble à f ibre opt ique.
3 Introduct ion This guide describes and pr ovides insta llation instruc tions for Nortel Netw orks* medi a dependent adapters (MDAs). It contains the follo wing topics : • “ Suppo rted inte rface.
4 Supported inter faces and products Ta b l e 1 shows the in terface ty p es use d with the MDAs described in this gui de. MDA descripti ons This sectio n describes the fol lowing MDAs: • “ 10BASE.
5 • “ GBIC MDA ” on pa ge 22 10BASE-T/100BASE-TX MDAs The 10BASE-T/100 BASE-TX MDAs use four RJ-45 (8-pin modular) conn ectors, confi gu red as media de pendent int erface- crossover (MDI-X) connectors.
6 Figure 1 400 -4T X and 8100- 4TX MDA front pan els The 10BASE-T/10 0BAS E -TX MDA port s can operate at ei ther 10 Mb /s or 100 Mb /s. The port speed is dete rmined throu gh autone gotiation wi th its connec ting device.
7 Ta b l e 2 describe s the 400-4T X and 8100 -4TX MDA fron t -panel. T ab l e 2 400-4T X an d 8100- 4TX MDA fron t panel Item Label Descriptio n 1 100 100B ASE-T X port s tatu s LEDs ( green ) : On: The c orresp onding por t is set to operate at 100 Mb/s.
8 Figu re 2 sh ows t he front pan el of the BP S2 000-4 TX M DA. Figure 2 BPS200 0-4T X MDA fr ont panel Ta b l e 3 describes the BPS2000-4TX MDA front-panel componen ts.
9 100BASE-FX MDAs The 100 BASE-FX MDAs confo rm to the IEEE 802.3u 100BASE -FX standard and can att ach fiber-base d 100 Mb/ s connect ions t o Fast Ethern et devic es. Th e 100B ASE-FX MDAs do not su pp ort s ing le-mod e f ib er ca b l e . The follow i ng are the 100B ASE-F X MDAs.
10 Figu re 3 sh ows t he front pan e l s of t he 400-2FX MDA an d the 8100-2 FX MDA. Figure 3 400 -2F X and 8100- 2FX MDA front pan els BS45071A RX TX 100BASE-FX RX TX 100BASE-FX Activity Link F Dx 81.
11 Ta b l e 4 describe s the dual - por t 400-2 FX MDA and the 81 00 - 2FX MDA front-pan el compon en ts. Figu re 4 sh ows t he front pan el of the dual -port BPS 20 00-2FX MDA. T ab l e 4 400-2FX M DA an d 8100-2F X MDA descr ipt io n Item Label Description 1 Link Commu nications link L EDs (gree n): On: Valid communications link.
12 Figure 4 BPS200 0-2F X MDA fr ont panel Ta b l e 5 descri be s the dual - port BPS2 000-2FX MDA front- pa nel componen ts. T ab l e 5 BPS2000- 2FX M D A d esc ription Item Label Description 1 Link Li nk status L EDs (gre en): On (gree n): Valid 100 Mb/s comm unications link.
13 Quad-port 100BAS E-FX MD As The qu ad-p ort 100B AS E-FX M DAs use fou r long wav e 13 00 nm MT -RJ connectors to att ac h devices over 62 .5/125 micro n multimod e fiber optic cable. Figu re 5 sh ows t he front pan e l s of t he 400-4FX MDA an d the 8100-4 FX MDA.
14 Ta b l e 6 describe s the 400-4F X MDA and the 8100-4FX M DA front-panel components. Figu re 6 sh ows t he front pan el of the BP S2 000-4 FX M DA. T ab l e 6 400-4FX MDA / 8100-4FX MDA descriptio n Item Label Descriptio n 1 Link Commu nications link L EDs (gree n): On: Valid communications link.
15 Figure 6 BPS200 0-4F X MDA fr ont panel Ta b l e 7 describes the BPS2000-4FX MDA front-panel componen ts. T ab l e 7 BPS2000- 4FX M D A d esc ription Item Label Descriptio n 1 Link Link status LEDs (green): On (gree n): Valid 100 Mb/s comm unications link.
16 1000BASE-X MDAs The following are the 1000BASE -FX MDAs. For a com plete list of MDAs, se e T abl e 1 on page 4 . For installatio n instru ctio ns, see “ Instal ling an MDA ” o n page 24 . Shortwave G igabit MDAs The foll owing 10 00BASE - SX MDAs confo rm to th e IEEE 802.
17 Figure 7 450 -1S R and 450-1SX M DA fron t panels 1000BASE-SX TX RX Phy Link Activity 450-1SX MDA TX RX 1000BASE-SX RX 1000BASE-SX TX Activity Link Phy Select 450-1SR MDA 3 BS45044A 4 3 4 450-1SR M.
18 Ta b l e 9 describe s the 450-1S R MDA and the 450 -1SX MDA front panel c omponen ts. T ab l e 9 450-1SR / 450- 1S X MDA descr ip t ion Item Label Description 1 Link Commu nicat i on lin k LEDs (gr ee n): On: Valid communications link. Off: The co mmunicatio ns link connec tion is bad or th ere is n o connection to this por t.
19 Longwave Gigabit MDAs The foll ow ing 1000 BASE-L X MDAs confo rm to the IE EE 802.3z 1000BASE -LX standar d and use long wave 1300 n m fiber opt ic co n nectors to co nn ect dev ic es ov er single mod e (5 km/3 .1 mi) or mu ltimode (550 m/1805 ft) fib er optic ca ble.
20 Figure 8 450 -1L R and 450 -1LX MDA fro nt pan el s 1000BASE-LX TX RX Phy Link Activity 450-1LX MDA BS45045A 3 4 2 1 TX RX 1000BASE-LX RX 1000BASE-LX TX Activity Link Phy Select 450-1LR MDA 3 4 2 1.
21 Ta b l e 1 0 descr ibes the 45 0-1LR MDA and t he 450 -1LX MDA front-panel comp onents. T ab l e 10 450-1L R and 4 50-1LX MDA des cription Item Label Description 1 Link Commu nicat i on lin k LEDs (gr ee n): On: Valid communications link. Off: The co mmunicatio ns link connec tion is bad or th ere is n o connection to this por t.
22 GBIC MDA The 450-1 GBIC MDA ( Fig ure 9 ) has a single Host port for Gigabit Interface Co nverters (GBICs). GBICs are hot-swappa ble input/ou tput e nhance ment com ponen ts that li nk Gigab it Etherne t ports with fi ber o ptic ne tworks.
23 Figure 9 450-1 GBIC M D A Fr ont Pa nel GBIC Phy Link Activity 450-1GBIC MDA BS450102A 3 4 450-1GBIC MDA 2 1 GBIC model with extr actor tabs GBIC model with extr actor handle SC connector.
24 Ta b l e 1 1 descri bes th e 450-1 GBIC MD A front-p anel componen ts. Inst allin g an MDA Befo re you begin i nstalling an MDA, see “ MDA descriptions ” on page 4 for specif ic informa tion ab out your M DA.
25 The Uplin k/Expansi on Modu le slot on su pported swi tches accomm oda tes a singl e MDA using the f ol l owing conn ectors. T o install an MDA: 1 Unplug the A C power co rd from the back of the swit ch , or unplug the switch mo dule from t he switch back plane.
26 Figure 10 Installi ng an MDA 4 Press the M DA firmly into t he Uplink/Expansio n Module slot. Be sure that the MDA is fully seat ed into the mati ng connect or .
27 For instructions on attaching devices to the MDA ports, refer to the p ublication for y our switch. After co nnecting th e port cables, follow th e i nst ru ctions to conn ect po wer and verify the installa tion .
28 Inst al ling a G B IC in a n MDA Before installing a GBIC, see “ GBIC MDA ” on page 22 for specif ic infor m a tion ab out your M DA. The 450-1 GBIC MDA Hos t port is covered wit h a spring- loaded filler pane l t hat ro tat es out of th e way as y ou pu sh th e GBIC int o place.
29 Figure 1 1 Installing a GBI C 3 Press on th e front of the GBIC u ntil it snaps into p lace. 4 Remove the ru bber plug to con nect ca bles. Removing an Installed GBIC fr om an MDA For a descri ption of the GB IC MDA, see “ GBIC MDA ” on page 22 .
30 Figure 12 Remo ving a GBIC w ith sp ring tab s • If the GBIC has an extractor handl e ( Figur e 9 on pag e 23 ), grasp th e handle and pull firmly to remove th e GBIC from the MDA ’ s Host port.
Een belangrijk punt na aankoop van elk apparaat Nortel Networks 302403-G (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Nortel Networks 302403-G heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Nortel Networks 302403-G vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Nortel Networks 302403-G leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Nortel Networks 302403-G krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Nortel Networks 302403-G bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Nortel Networks 302403-G kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Nortel Networks 302403-G . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
