Gebruiksaanwijzing /service van het product 4070 van de fabrikant Nortel
Ga naar pagina of 44
Nor tel Secure Network Access Installation — Quic k Star t Switch 4070 NN47230-303 324392-A ..
Nortel Secure Network Access Document status: Standard Document version: 01.01 Document date: 28 July 2008 Copyright © 2008, Nor tel Networks All Rights Reser v ed.
3 Contents Regulatory Information and Safety Precautions 5 International Regulatory Statements of Conformity 5 National Electromagnetic Compliance (EMC) Statements of Compliance 5 FCC statement (USA o.
4 Contents Safety precautions 21 Safety precautions na vigation 21 Installation checklist 23 Installation 25 Navigation 25 Unpacking the de vice 25 Installing an NSNA device into a rac k 26 Prerequisi.
5 Regulatory Information and Safety Precautions Read the information in this section to lear n about regulator y conf or mities and compliances. International Regulatory Statements of Conformity This .
6 Regulatory Information and Safety Precautions ICES statement (Canada only) Canadian Depar tment of Communications Radio Interference Regulations This digital apparatus (Nor tel Secure Network Access.
NOM statement (Mexico only) 7 • EN 55024 (IEC 61000-4-2, -3, -4, -5, -6, -8, -11)–Electromagnetic Immunity • EN 61000-3-2 (IEC 610000-3-2)–P ower Line Har monics • EN 61000-3-3 (IEC 610000-3.
8 Regulatory Information and Safety Precautions Exporter: Nortel Networks, 4655 Great America Parkway, Santa Clara, CA 95054 USA. Importer: Nortel Networks de México, S.A. de C.V. Avenida Insurgentes Sur #1605 Piso 30, Oficina Col. San Jose Insurgentes Deleg-Benito Juarez México D.
Notices 9 National En vironmental Statements of Compliance The WEEE Directive 2002/96/EC and RoHS (Restriction of Hazardous Substances) Directive 2002/95/EC sets collection, recycling and recov er y targets f or various categor ies of electr ical products and their waste.
10 Regulatory Information and Safety Precautions CA UTION Caution notices provide information about how to av oid possible service disruption or damage to Nor tel products. W ARNING W ar ning notices provide inf or mation about how to av oid personal injury when working with Nor tel products.
T rademarks 11 CA UTION T o reduce the risk of fire, use only number 26 A WG or larger UL Listed or CSA Cer tified T elecommunication Line Cord f or all network connections. W ARNING Before working on this equipment be aware of good saf ety practices and the hazards inv olv ed with electrical circuits.
12 Regulatory Information and Safety Precautions Nor tel Secure Network Access Installation — Quick Star t Switch 4070 NN47230-303 01.01 Standard 2.0 28 July 2008 Copyright © 2008, Nor tel Networks .
13 Software license This section contains the Nor tel Networks software license. Nortel Networks software license agreement This Software License Agreement ("License Agreement") is between you, the end-user ("Customer") and Nor tel Networks Cor poration and its subsidiaries and affiliates ("Nor tel Netw or ks").
14 Software license as e xpressly author ized; b) re verse assemble , rev erse compile, re verse engineer or otherwise translate the Software; c) create der ivativ e works or modifications unless e xpressly author ized; or d) sublicense, rent or lease the Software.
Nor tel Networks software license agreement 15 documentation are gov er ned by Nor tel Networks standard commercial license in accordance with U .S. F ederal Regulations at 48 C .F .R. Sections 12.212 (for non-DoD entities) and 48 C .F .R. 227.7202 (f or DoD entities).
16 Software license Nor tel Secure Network Access Installation — Quick Star t Switch 4070 NN47230-303 01.01 Standard 2.0 28 July 2008 Copyright © 2008, Nor tel Networks .
17 Ne w in this release The f ollowing sections detail what’s new in Nor tel Secure Network Access Installation — Quick Star t Switch 4070 (NN47230-303) for Release 2.0. • "F eatures" (page 17) • "Other changes" (page 17) Features This is the first standard release of the document.
18 New in this release Nor tel Secure Network Access Installation — Quick Star t Switch 4070 NN47230-303 01.01 Standard 2.0 28 July 2008 Copyright © 2008, Nor tel Networks .
19 Intr oduction The Nor tel Secure Network Access Switch (NSNA) 4070 Quick Star t Guide provides basic instructions about installing the hardware and performing basic configuration and management of the network.
20 Introduction Nor tel Secure Network Access Installation — Quick Star t Switch 4070 NN47230-303 01.01 Standard 2.0 28 July 2008 Copyright © 2008, Nor tel Networks .
21 Installation preparation This section provides basic inf or mation about the Nor tel Secure Netw ork Access Switch (NSNA) 4070 and the checklist of the shipped accessor ies.
22 Installation preparation • T o promote proper air circulation, ensure the de vice vents are not bloc k ed or obstructed by cables , panels, ser ver r ack fr ames, or other materials. A minimum of 15 centimeters (6 inches) of space provides proper airflow .
Installation checklist 23 Installation chec klist This checklist represents the high-le vel tasks that must be perf or med to successfully install the Nor tel Secure Network Access Switch. De vice installation inv olves the f ollowing steps: Procedure steps Step Action 1 Choose a suitable location to install the de vice.
24 Installation preparation Nor tel Secure Network Access Installation — Quick Star t Switch 4070 NN47230-303 01.01 Standard 2.0 28 July 2008 Copyright © 2008, Nor tel Networks .
25 Installation This chapter contains installation instructions f or the Nor tel Secure Network Access Switch (NSNA). Navigation • "Unpacking the de vice" (page 25) • "Installing an.
26 Installation Check Accessory Use to copper network interface card Connect the network cables. Console cable Establish a console connection to the device. —End— Installing an NSNA device into a rack Install an NSNA in a standard equipment rac k.
Installing an NSNA device into a rack 27 2 Align the slide rail with the front mounting flange by aligning the score mark on the slide rail ( 1 ) with the score mar k on the rail between the upper and lower U . Push outward on the slide r ail latch to close to the latch and secure the slide rail.
28 Installation 3 Extend the slide rails fully from the ser ver r ack until they loc k. Align the tabs on the slide rails with the matching inser ts on the device ( 1 ) and lower the ser ver onto the slide rails.
Installing an NSNA device into a rack 29 5 Lift the locking le vers ( 1 ) on the slide rails and slide the de vice into the ser ver rac k until it extends appro ximately 10.16 centimeters (4 inches) from the rack. 6 Slide the device into the ser ver r ack cabinet until the release latches ( 1 ) lock into place.
30 Installation —End— A TTENTION T o remove the de vice, rev erse these instructions. Cabling the de vice This section describes about cabling the de vice f or network and console connections.
Cabling the de vice 31 Procedure steps Step Action 1 Prepare either an ASCII ter minal or a computer running ter minal emulation software to ser ve as the command device .
32 Installation Nor tel Secure Network Access Installation — Quick Star t Switch 4070 NN47230-303 01.01 Standard 2.0 28 July 2008 Copyright © 2008, Nor tel Networks .
33 Configuration This chapter contains configuration instructions f or commissioning the Nor tel Secure Network Access Switch. Navigation • "Creating a new cluster" (page 33) • "J.
34 Configuration 3 T o initiate the system connection process, press ENTER on the terminal. 4 At the login prompt, log in as user : admin. 5 At the pass word prompt, enter the administrator password.
Creating a new cluster 35 Enter network mask [255.255.255.0]: Specify the desired network mask or accept the suggested value by pressing ENTER. If a connected router or s witch attaches VLAN tag IDs to incoming packets , specify the VLAN tag ID used. 10 Setup a two armed configuration.
36 Configuration Generate new SSH host keys (yes/no) [yes]: This may take a few seconds...ok Enter a password for the "admin" user: Re-enter to confirm: T o maintain a high le vel of security while using an SSH connection, accept the default choice to generate new SSH host ke ys.
Joining an SNAS to an existing cluster 37 Procedure steps Step Action 1 Choose join from the Setup menu to add an SNAS to an e xisting cluster . 2 Specify the por t to be used for netw ork connectivity . Enter port number for the management interface [1-3]: This por t is automatically assigned to Interface 1.
38 Configuration 6 Enter the Management IP address (MIP) of the existing cluster . Provide the Management IP address of the cluster to which you want to join the ne w SNAS. T o check the Management IP of an e xisting cluster , connect to the cluster and use the /cfg/sys/cur command.
Enabling the browser-based interf ace 39 T o enable the BBI, perform the follo wing procedure: Procedure steps Step Action 1 Establish a console connection or T elnet session with the device . 2 Log into the s witch with an administrativ e user name and passw ord.
40 Configuration >> Administrative Applications# https 9 (Optional) F rom the HTTPS access menu, designate a por t f or HTTPS access using the port command. >> HTTPS# port <port_number> Using a por t other than 4443 requires the user to designate the por t when accessing the BBI.
Applying the Nor tel SNAS license 41 Part Number Description EB1639183 Secure Network Access License - Add 2000 concurrent endpoints EB1639184 Secure Network Access License - Add 5000 concurrent endpoints Procedure steps Step Action 1 Contact Nor tel Customer Suppor t and purchase par t number .
42 Configuration —End— Through CLI Procedure steps Step Action 1 Enter the command /cfg/sys/host <host_number>/license . 2 Enter the ke ycode. >> Main# /cfg/sys/host <host_number>/license 3 Press Enter on the ke yboard to create a new line and type three periods (.
.
Nor tel Secure Network Access Installation — Quic k Star t Switch 4070 Copyright © 2008, Nor tel Networks All Rights Reser ved. Publication: NN47230-303 Document status: Standard Document version: 01.01 Document date: 28 July 2008 T o provide feedbac k or repor t a prob lem in this document, go to h ttp://www .
Een belangrijk punt na aankoop van elk apparaat Nortel Nortel 4070 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Nortel Nortel 4070 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Nortel Nortel 4070 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Nortel Nortel 4070 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Nortel Nortel 4070 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Nortel Nortel 4070 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Nortel Nortel 4070 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Nortel Nortel 4070 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
