Gebruiksaanwijzing /service van het product BBC547 van de fabrikant Norton Abrasives
Ga naar pagina of 36
OWNERS MANUAL COMPACT MASONRY SAW MODELS BBC157 BBC207 BBC547 FORM <<7506 rev 2/2006.
2 WARRANTY Norton warrants all products manufactured by it against defects in workmanship or materials for a period of one (1) year from the date of shipment to the customer.
3 BBC 157/207/547 OWNER'S MANUAL CONTENTS PAGE I. Preparation A. Safety Precautions 4-6 B. Assembly 7-12 C. Specifications 13 D. Electrical Connections 14 E. Wiring Diagram 15 F. Gasoline Engine 16 II. Operation A. How to mount Blade 17 B. How To Use "Step Cutting" with abrasive blades 18 C.
4 I. PREPARATION A. Safety Precautions Important! The following safety precautions must always be observed. Hazard Symbols Fuel (gasoline) is extremely flammabl e and its vapors can explode if ignited. Store gasoline only in approved container s, in well-ventilated, unoccupied approved areas, and away from sparks or fl ames.
5 Dust and Silica Warning Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm.
6 1. Before mounting any blade on the saw, th e blade should be inspected for any damage which might have occurred during shipment, handling or previous use. 2. The blade collars and arbors should be cleaned and examined for damage before mounting the blade.
7 I. PREPARATION B. Assembly The compact Masonry saws are shipped completely assembled and ready for use except for diamond blade, gasoline, oil, and Head Locking Bar. Inspect the saw for shipping damage. If any damage is found, contact the shi pper immediately and file a freight claim.
8 Figure 1: Head Locking Screw Removal Figure 2: Head Locking Handle Installation Depth Limiting Bolt: Remove the 12mm Carriage Bolt, 12mm Large Flat Washer (DIN9021), 12mm Flat Washer, 12mm Lock Washer, and 12mm Nut from the plastic Bag. Place the 12mm Large Washer over the 12mm Carriage Bolt.
9 Leg Assembly: Remove the four (4) Legs from the Saw Wate r Pan, and the four (4) Plastic Handle Knobs and four (4) Square Nuts from the plastic bag. Place one (1) Square Nut into each of the Nut Retaining Brackets located on each of the Leg Holders.
10 Conveyor Cart Assembly : Remove the Conveyor Cart and Back Stop from the Saws Water Pan, and the Wing Nuts, Carriage Bolts, Washers, and Cart Stop from t he plastic bag. Slide one (1) Carriage Bolt thru each of the three (3) Square Holes located on the front of the Conveyor Cart.
11 Figure 8: Guide-A-Cut Assembly Water Curtain Assembly: Remove the Water Curtain from the Saw Water Pan. Attach the Water Curtain Spring Clips to the Pivoting Bar Located Under the Cutting H ead. Note that the rough side of the Water Curtain should face towards the front of the sa w.
12 Figure 10: Wrench Placement Water Pump Assembly: The Water Pump requires no additional assembly..
13 I. PREPARATION C. BBC157/207/547 Series Masonry Saw Specifications Dimensions/Weight Length (Working) 60” (1524mm) Width 24” (965mm) Height (Electric) 34” (864mm) Height (Gas) 38” (965mm) Weight (Electric) Uncrated 250lbs (kg) Weight (Gas) Uncrated 275lbs (kg) Electric Motor Motor Mfg.
14 I. PREPARATION D. Electrical Connections Important -Before connecting the motor leads to the power supply be sure that the voltage, cycles and phase shown on the nameplate of the motor correspond to the available power supply. Voltage Selection For Single Phase Motors 1-1/2 h.
15 D. Wiring Diagram Be sure to ground the saw properly before operating, such as a ground wire connection provided by the power company. Electrical Connections 115 Volt 230 Volt For any Electric Motor service, warranty , or technical related questi ons please contact your neares t Baldor service center: Baldor Electric Company 5711 R.
16 I. PREPARATION F. Gasoline Engine Prior to attempting to operate the engine, r ead the information contained in the engine owner's manual. An engine owner’s manua l is supplied with every gasoline powered concrete saw. 1. Check Oil: Add oil if low.
17 II. OPERATION A. Installing the Blade 1. For Gasoline powered machines disconnect the spark plug and for Electrical Powered Machines disconnect from power source.
18 II. OPERATION B. How To Use " Step Cutting " With Abrasive Blades Use "step cutting" without exception w hen cutting wet or dry with abrasive blades. "Jam cutting", which is discussed and illustrated in the section following, is to be used only with wet and dry cutting diamond blades.
19 II. OPERATION C. How To Use "Jam Cutting" (Fixed Cutting) and "Step Cutting" With Diamond Blades In "Jam" cutting the head is locked in a fixed position and the material is pushed into it as shown in the sketch at the bottom.
20 II. OPERATION D. How To Use Blockbuster Compact For Dry Cutting 1. Use a proper blade, which is marked for dry cutting. 2. Remove the water curtain. 3. Disconnect the water pump. 4. Use "step" cutting as explained previously when using abrasive blades.
21 III. MAINTENANCE The Blockbuster Compact requires very little ma intenance for long satisfactory operation. However, the following points must be watched: A. V-Belts The drive belts are made of premium oil and heat re sistant materials. T hey require very little adjustment, but should be tightened after the first few days of running.
22 III. MAINTENANCE B. Motor The motors are specially designed for masonry sawing. It is totally enclosed and the sealed bearings require no lubrication. The motor is equipped with thermal overload protection. 1. Periodically clean the dirt and sludge build-up from the motor fan housing and cooling fins.
23 Note: Never operate saw without bearing cover in place. For normal conditions the grease should conform to the NLGI grade two consistency and be free of any chemical impurities such as free acid or free alkali, dust, rust, metal particles or abrasives.
24 V. PARTS LIST SECTION A. Ordering Information 1. List model number and serial number of machine. 2. List the part number and descripti on of part (not item number). 3. Whenever alternate parts are shown due to product improvement, inspect the part you have and provide additional description as necessary.
25 V. PARTS LIST SECTION Power Plant (BBC547) Gasoline S1 S2.
26 Power Plant (BBC547) Gasoline Item No Description Part Number 1 Honda motor GX160 83715 2 Motor pulley 83716 3 Belt XPZ 562 LW 83717 4 Jackshaft pulley 83718 5 Right belt guard 83719 6 Guard for th.
27 Power Plant (BBC157-207) Electric Item No Description Part Number M1 Motor Assembly w/Switch 1-1/2HP 115/230v/60/1 Motor Assembly w/Switch 2 HP 115/230v/60/1 232084 232085 M2 Capacitor Box Large (T.
28 Frame (Common All BBC157-207-547)).
29 Frame (Common All BBC157-207-547)) Item No Description Part Number 18 Screws for water pump 75280 19 Frame 83727 20 Leg set of 4 75817 21 Wheel 82733 22 Wrench 19mm 70807 23 Wrench 22mm 72143 24 Drain plug 76095 25 Splited bearing 83728 26 Water pump fixation spring 76097 27 Support post 83729 28 Water pump complete.
30 Cutting Head (Common All BBC157-207-547).
31 Cutting Head (Common All BBC157-207-547) Item No Description Part Number 35 Locking Handle for cutting head (was 73098 replaced by 82738) 82738 36 Spring 72567 37 Cutting head 83724 38 Protection f.
32 Cutting Table (Common All BBC157-207-547).
33 Cutting Table (Common All BBC157-207-547) Item No Description Part Number 56 Conveyor Cart (aka Cutting Table) Complete With Wheels, Top, Back Stop, and Conveyor Cart Stop 83754 57 Top For Cutting .
34 C. Baldor Service Policy.
35 D. Honda Service Policy.
36 Saint-Gobain Abrasives, Inc. Norton Construction Products 2770 West Washington Street Stephenville, TX 76401 Phone: 800-554-8009 or 254-918-2310 Fax: 800-443-1092 or 254-918-2312 SOLD AND SERVICED .
Een belangrijk punt na aankoop van elk apparaat Norton Abrasives BBC547 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Norton Abrasives BBC547 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Norton Abrasives BBC547 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Norton Abrasives BBC547 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Norton Abrasives BBC547 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Norton Abrasives BBC547 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Norton Abrasives BBC547 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Norton Abrasives BBC547 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
