Gebruiksaanwijzing /service van het product RD260A van de fabrikant Omega Engineering
Ga naar pagina of 25
http://www.omega.com e-mail: info@omega.com U ser ’ s Guide R D 2 6 0 A R E C O R D E R U s e r s M a n u a l.
Servicing North America: USA: One Omega Drive, Box 4047 ISO 9001 Certified Stamford, CT 06907-0047 T el: (203) 359-1660 F AX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1 T el: (514) 856-6928 F AX: (514) 856-6886 e-mail: info@omega.
i Notes • The contents of this manual are subject to change without prior notice as a result of improvements in the instrument’s performance and functions. Display contents illustrated in this manual may differ slightly from what actually appears on your screen.
ii SAFETY PRECAUTIONS This recorder is developed to satisfy and to be used under the following conditions: • It is a component type instrument to be installed on an instrumentation panel or rack. • It complies with the IEC class II safety standard.
iii Using the User ’ s Manual This manual contains information about the instrument’s functions and operating procedures as well as precautions that should be observed during use. T o ensure proper use of the instrument, please read this manual thoroughly before operating it.
iv Using the User ’ s Manual Conventions Used in this Manual Displayed characters Bold alphanumeric characters enclosed with [ ] refer to characters or setting values that are displayed on the screen. Symbols The following symbol marks are used to attract the operator ’s attention.
v Contents SAFETY PRECAUTIONS ............................................................................................................. ... ii Using the User ’ s Manual ............................................................................
1-1 1 Before Operation 1.1 Front/Rear Panels: Functions and Display Front Panel CH DA T A RCD ALM ESC RCD CH UP FEED MENU 1 Power switch 3 Chart cassette 2 Key panel 5 Display 4 Status display 1. Power switch (push-button type) Pressing the switch turns the power ON and OFF .
1-2 3. Chart cassette Contains a Z-fold chart (width: 100 mm, length: 16 m). 4. Status Display RCD indicator: illuminated when recording of measurement values is in progress. ALM indicator: illuminates when an alarm occurs. 5. Seven-segment character display Used to display data, setting screen, and so on.
1-3 1 Before Operation 1.2 Handling Precautions Safety precautions • Before you use this recorder make sure to read the Safety Precautions on page 2 of this manual.
2-1 2 Daily Operation 2.1 Recording Switching Power ON/OFF The power switch is located at the lower right-hand corner of the front face behind the door . The switch is a push-button type. Press the switch to turn the recorder ON and press again to turn it OFF .
2-2 2.2 Selecting the Display Three different displays can be selected: Auto, Manual, and dislay OFF . If the DISP key is pressed you the recorder will change the display modes in the order of AUTO > MANUAL > OFF , Note that manual display can’t be selected on the 1-pen model.
2-3 2 Daily Operation 2.3 Recorder Modes The recorder has three modes as described below: Operation Mode This is the mode for daily operation; when the power turns on, the recorder automatically enters this mode. Select from the following functions by pressing the appropriate keys on the key panel.
2-4 2.4 Loading Chart Paper Installing / Replacing Chart Paper 1. Open the front door of the recorder , as shown below. 2. Make sure that recording is OFF .
2-5 2 Daily Operation Loading Chart Paper 7. Load the chart paper into the chart compartment; the small perforations should be at the left-hand. Make sure that the sprocket teeth of the chart drives are properly engaged in the chart paper perforations.
2-6 2.5 Installing/Replacing Pens (Pen Model) CAUTION • Do not press or pinch the felt tip to prevent deformation. Do not move the pen holder up- or down-scale to protect the driving mechanism. • Always make sure to remove the pen cap before installation.
2-7 2 Daily Operation Replacement under pen-replacement mode When a pen is located at a place where its replacement is difficult to do, relocate the pen by the following procedures: 1. Make sure that recording is OFF . The main Power switch must be ON.
2-8 2.6 Installing/Replacing the Ribbon Cassette (Dot Model) CAUTION • Improper cassette insertion may cause faulty print color or damage the cassette. 1. Open the front door , and make sure that power is switched OFF . 2. Open the display by pulling its left end.
3-1 3 Maintenance 3.1 Periodic Inspection Check the following items periodically , and replace parts, if necessary: Character printing Are recorded lines or printed characters clear , not blurred? T o replace a felt-tip pen, refer to the User ’s Manua l Section 2.
3-2 3.2 Fuse Don’t replace the fuse by yourself. Never take the recorder apart if the fuse needs to be replaced. Contact your nearest Omega sales representative if the fuse needs to re replaced.
4-1 4 T roubleshooting 4.1 Error Messages Error Code List Please contact the dealer from which you purchased this recorder in case the following errors appear . See the T echnical Manual , Section 6, for more error messages. Error Codes Meaning Recovery Main memory reading error.
4-2 4.2 T roubleshooting See the T echnical Manual , Section 6, for more troubleshooting information. Is the power supply properly connected? Does the power meet the specified rating? NO NO NO YES YES YES Recorder is completely inoperative: Is the power switch ON? Does the switch turn properly? Connect the supply lines properly.
Index-1 Index Index Index Index F FEED key .......................................................................... 1-1 Feeding Chart Paper ......................................................... 2-1 Functions .....................................
W ARRANT Y / DISCLAIMER O M E GA E N GI NEE R ING , IN C. war rant s this u ni t to be f r ee o f d ef e ct s in mater ia ls and wor km an sh ip for a p e riod of 25 mon t hs f r o m dat e of pur cha se .
M3287/0299 W h e r e D o I F i n d E v e ry t h i n g I N e e d f o r P r o c e s s M e a s u r e m e n t a n d C o n t r o l ? O ME G A … O f C o u r s e ! T E M P E R AT U R E Th e rm ocou pl e, R.
Een belangrijk punt na aankoop van elk apparaat Omega Engineering RD260A (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Omega Engineering RD260A heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Omega Engineering RD260A vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Omega Engineering RD260A leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Omega Engineering RD260A krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Omega Engineering RD260A bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Omega Engineering RD260A kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Omega Engineering RD260A . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
