Gebruiksaanwijzing /service van het product Combo (2012) van de fabrikant Opel
Ga naar pagina of 162
Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 19 Seats, restraints ........................... 34 Storage ........................................ 47 Instruments and controls .
2 Introduction Introduction.
Introduction 3 Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available under the sections "Service and Maintenance" and "Technical data" as well as on the identification plate.
4 Introduction Danger, Warnings and Cautions 9 Danger Text marked 9 Danger provides information on risk of fatal injury. Disregarding this information may endanger life. 9 Warning Text marked 9 Warning provides information on risk of accident or injury.
Introduction 5.
6 In brief In brief Initial drive information Vehicle unlocking Turn the key in the driver's door lock to the front or press button q to unlock the doors. Open the doors by pulling the handles. To unlock the leaf doors, turn the key to the vertical position or press button q .
In brief 7 Seat adjustment Seat positioning Pull handle, slide seat, release handle. Move the seat until it engages. Seat adjustment 3 36, Seat position 3 35. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment.
8 In brief Head restraint adjustment Tilt forward to release, hold in place, adjust height and release again. Head restraints 3 34. Seat belt Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body.
In brief 9 Exterior mirrors Manual adjustment Adjust the exterior mirror manually using the handle. Electric adjustment First select the relevant exterior mirror with the rocker switch and adjust with the four-way switch. Electric adjustment 3 30, Convex exterior mirrors 3 30, Folding exterior mirrors 3 30, Heated exterior mirrors 3 31.
10 In brief.
In brief 11 Instrument panel overview 1 Light switch .......................... 75 2 Side air vents ........................ 82 3 Turn and lane-change signals, headlight flash, low beam and high beam ..... 77 4 Horn ...................................
12 In brief.
In brief 13 Exterior lighting Turn light switch 7 = Off 8 = Sidelights 9 = Headlights Press light switch 0 = Courtesy lights Push button > = Front fog lights r = Rear fog lights Lighting 3 75.
14 In brief Hazard warning flashers Operated with the ¨ button. Hazard warning flashers 3 76. Horn Press j . Washer and wiper systems Windscreen wiper & = fast % = slow $ = interval wiping § = off Windscreen wiper 3 57, Wiper blade replacement 3 104.
In brief 15 Windscreen washer systems Pull lever. Windscreen washer system 3 57, Washer fluid 3 103. Rear window wiper and washer system Wiper on = push lever Wiper off = pull lever Wash = push lever and hold Rear window wiper and washer system 3 58, Wiper blade replacement 3 104, Washer fluid 3 103.
16 In brief Demisting and defrosting the windows Set temperature control to warmest level. Set fan speed to highest level. Set air distribution to V . Cooling n on.
In brief 17 Starting off Check before starting off ■ Tyre pressure and condition 3 119, 3 150. ■ Engine oil level and fluid levels 3 101. ■ All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and are operational.
18 In brief ■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface. ■ Close windows and sunroof. ■ The engine cooling fans may run after the engine has been switched off 3 100.
Keys, doors and windows 19 Keys, doors and windows Keys, locks ................................... 19 Doors ........................................... 25 Vehicle security ............................ 27 Exterior mirrors ............................ 30 Interior mirrors .
20 Keys, doors and windows Used to operate: ■ Central locking system, ■ Anti-theft locking system, ■ Anti-theft alarm system, ■ Power windows. The radio remote control has an approximate range of up to 5 metres. This range can be affected by outside influences.
Keys, doors and windows 21 Radio remote control synchronisation After replacing the battery, unlock the door with the key in the driver's door lock. The radio remote control will be synchronised when you switch on the ignition. Central locking system Unlocks and locks doors, load compartment and fuel filler flap.
22 Keys, doors and windows Locking Close doors, load compartment and fuel filler flap. If the driver's door is not closed properly, the central locking system will not work. Central locking system with key activation Turn the key in the driver's door lock rearwards.
Keys, doors and windows 23 Fault in central locking system Unlocking Turn the key in the driver's door lock towards front of vehicle. The other doors can be opened by pulling the interior handle (not possible if the anti-theft locking system is active).
24 Keys, doors and windows Relock the tailgate by closing it and turning the key to the horizontal or vertical position. In the horizontal position, the tailgate will be unlocked the next time the vehicle is unlocked via the central locking system.
Keys, doors and windows 25 Child locks 9 Warning Use the child locks whenever children are occupying the rear seats. Using a key or suitable screwdriver, turn the rotary knob on the door lock from the vertical position. The door cannot be opened from inside.
26 Keys, doors and windows Load compartment Tailgate Opening Press the button to open the tailgate. 9 Warning Do not drive with the tailgate open or ajar, e.
Keys, doors and windows 27 When the doors are open 180°, the rear exterior lighting is covered. Therefore, only open the doors until they engage when it is dark outside. When closing, make sure that the stop lug properly engages in the guide rail. Closing Push first the left and then the right leaf door past slight resistance.
28 Keys, doors and windows Activation without monitoring of passenger compartment and vehicle inclination Switch off the monitoring of passenger compartment and vehicle inclination when animals are being left in the vehicle, because of high volume ultrasonic signals or movements triggering the alarm.
Keys, doors and windows 29 If the alarm is triggered when the driver’s door is opened, deactivate the anti-theft alarm system by switching on the ignition. Opening and closing tailgate/ leaf doors with activated anti- theft alarm system To unlock: 1.
30 Keys, doors and windows Exterior mirrors Convex shape The convex exterior mirror reduces blind spots. The shape of the mirror makes objects appear smaller, which will affect the ability to estimate distances. Manual adjustment Adjust mirrors by swivelling lever in required direction.
Keys, doors and windows 31 Heated Operated by pressing the Ü button. Heating works with the engine running. Interior mirrors Manual anti-dazzle To reduce dazzle, adjust the lever on the underside of the mirror housing. Windows Manual windows The door windows can be opened or closed with the window winders.
32 Keys, doors and windows Window in the sliding doors To open = Release joint and push outwards. To close = Pull joint and engage. Power windows 9 Warning Take care when operating the power windows. Risk of injury, particularly to children. Keep a close watch on the windows when closing them.
Keys, doors and windows 33 Press p until all windows are closed. Overload If the windows are repeatedly operated at short intervals, the window operation is disabled for some time. Fault If the windows cannot be opened or closed automatically, activate the window electronics as follows: 1.
34 Seats, restraints Seats, restraints Head restraints ............................ 34 Front seats ................................... 35 Seat belts ..................................... 38 Airbag system .............................. 40 Child restraints .
Seats, restraints 35 Head restraints on centre rear seats To fold the backrest, press the detent springs on the guide sleeves to release the head restraint and push it all the way down. Removing head restraint Release both catches by pressing and withdraw head restraint.
36 Seats, restraints ■ Sit with shoulders as far back against the backrest as possible. Set the backrest to an angle so that it is possible to reach the steering wheel with arms slightly bent. Maintain contact between shoulders and the backrest when turning the steering wheel.
Seats, restraints 37 Seat height Lift lever and relieve some weight from seat to raise it or press down on seat with body weight to lower it. Seat folding Lift release lever and tilt backrest forwards. Heating Activate heating by pressing ß button for the seat with the ignition on.
38 Seats, restraints Seat belts The belts are locked during heavy acceleration or deceleration of the vehicle for the safety of the occupants. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves.
Seats, restraints 39 Triggered belt tensioners must be replaced by a workshop. Belt tensioners can only be triggered once. Note Do not affix or install accessories or other objects that may interfere with the operation of the belt tensioners.
40 Seats, restraints Airbag system The airbag system consists of a number of individual systems. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner.
Seats, restraints 41 9 Warning Optimum protection is only provided when the seat is in the proper position 3 35. Keep the area in which the airbag inflates clear of obstructions. Fit the seat belt correctly and engage securely. Only then the airbag is able to protect.
42 Seats, restraints Selecting the right system The rear seats are the most convenient location to fasten a child restraint system. Children should travel facing rearwards in the vehicle as long as possible. This makes sure that the child's backbone, which is still very weak, is under less strain in the event of an accident.
Seats, restraints 43 Child restraint installation locations Permissible options for fitting a child restraint system Weight and age class On front passenger seat On rear outboard seats On rear centre seat Group 0: up to 10 kg or approx. 10 months X U+ U Group 0+: up to 13 kg or approx.
44 Seats, restraints Permissible options for fitting an ISOFIX child restraint system Weight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat Group 0: up to .
Seats, restraints 45 ISOFIX size class and seat device A – ISO/F3 = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. B – ISO/F2 = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
46 Seats, restraints Isofix child restraint systems The mounting eyes for the ISOFIX child restraint system are located on the rear, outer seats between the seat back and the seat cushion. Fasten permitted ISOFIX child restraint systems to the mounting brackets.
Storage 47 Storage Storage compartments ................ 47 Load compartment ....................... 49 Roof rack system ......................... 54 Loading information ..................... 54 Storage compartments Glovebox The glovebox features a pen holder.
48 Storage Overhead console The stowage compartment above the front seats can hold a maximum load of 15 kg. The mesh packets above the doors can only hold light objects. 9 Warning Secure objects to prevent them from falling out and causing injury. Underseat storage Lift at recessed edge and pull out.
Storage 49 Load compartment Folding down rear backrests Push the rear, outer head restraint down completely or remove it. Push the rear, centre head restraint down completely 3 34. To fold one or both of the rear seat backrests, press the button at the top to release the backrest and fold it onto the seat cushion.
50 Storage To close Pull cover towards rear of vehicle using handle and hook into side retainers. To open Unhooked the closed cover at the rear. It rolls up automatically. Removing Open cover. Press button at right side of cartridge and engage by pushing right-hand end piece to the left.
Storage 51 Behind the rear seats Fold down both rear seat backrests. Hook tensioning straps into lashing eyes in floor and tighten by pulling on the loose end of the strap. Reposition and engage the backrests. Behind front seats Pull up both rear seat cushions and fold down rear seat backrests.
52 Storage To enlarge the load compartment, the grille can be moved forwards on the front passenger’s side. Push the head restraint of the front passenger seat down as far as it will go 3 34. Tilt front passenger’s seat backrest forward by raising release lever and push down to lock in position.
Storage 53 Van The warning triangle is kept in the compartment behind the driver’s seat. When the vehicle is being loaded, please ensure that nothing protrudes over the bottom edge of the opening. Disengage flap by pressing retaining lug and remove.
54 Storage Roof rack system Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended. Follow the installation instructions and remove the roof rack when not in use. Loading information ■ Heavy objects in the load compartment should be placed against the seat backrests.
Storage 55 9 Warning Always make sure that the load in the vehicle is securely stowed. Otherwise objects can be thrown around inside the vehicle and cause personal injury or damage to the load or car. ■ Do not cover the air outlets when stowing objects in the load compartment.
56 Instruments and controls Instruments and controls Controls ....................................... 56 Warning lights, gauges and indicators ..................................... 61 Information displays ..................... 70 Vehicle messages ....
Instruments and controls 57 Horn Press j . Windscreen wiper/washer Windscreen wiper Move lever upwards to switch on. & = fast % = slow $ = interval wiping § = off Do not use if the windscreen is frozen.
58 Instruments and controls Pull lever. Washer fluid is sprayed onto the windscreen and the wiper wipes a few times. Rear window wiper/washer Push lever forwards. The rear window wiper wipes in interval mode. Switch off by pulling the lever. If the lever is held forwards, washer fluid is sprayed onto the rear window.
Instruments and controls 59 Clock Time display in odometer To switch between trip odometer and time display give reset knob a short press. Setting the time On the clock display, press the setting knob on the instrument for approx. 2 seconds. The flashing value is set by pressing briefly.
60 Instruments and controls With the ignition on, press in cigarette lighter. It switches off automatically once the element is glowing. Pull out lighter. Ashtrays Caution To be used only for ash and not for combustible rubbish. Front ashtray Open the ashtray cover to the resistance point.
Instruments and controls 61 Warning lights, gauges and indicators Speedometer Indicates vehicle speed. Odometer With the ignition switched off, briefly press the reset knob to display the number of kilometres driven for approx. 15 seconds. The bottom line displays the recorded distance.
62 Instruments and controls Tachometer Displays the engine speed. Drive in a low engine speed range for each gear as much as possible. Caution If the needle is in the red warning zone, the maximum permitted engine speed is exceeded. Engine at risk. Fuel gauge Displays the fuel level in the tank.
Instruments and controls 63 Display: 1/1 - Tank pressure approx. 200 bar 3/4 - Tank pressure approx. 150 bar 1/2 - Tank pressure approx. 100 bar 1/4 - Tank pressure approx. 50 bar In order to achieve the maximum range in natural gas operation, we recommend that you make use of the entire reserve area.
64 Instruments and controls Engine coolant temperature gauge Displays the coolant temperature. left area = engine operating temperature not yet reached central area = normal operating temperature right area = temperature too high Caution If engine coolant temperature is too high, stop vehicle, switch off engine.
Instruments and controls 65 Transmission display The mode or selected gear is shown in the transmission display. R = Reverse gear N = Neutral position A = Manual transmission automated: automatic mode 1 - 5 = Current gear, manual transmission automated, manual mode Control indicators The control indicators described are not present in all vehicles.
66 Instruments and controls Control indicators in the instrument cluster.
Instruments and controls 67 Turn signal O illuminates or flashes green. Flashes The control indicator flashes if a turn signal is or the hazard warning flashers are activated. Rapid flashing: failure of a turn signal light or associated fuse, failure of turn signal light on trailer.
68 Instruments and controls Flashes with switched on ignition Fault in the immobiliser system. The engine cannot be started 3 29. Brake and clutch system R illuminates or flashes red. Illuminates Illuminates when the parking brake is released if the brake and clutch fluid level is too low 3 103.
Instruments and controls 69 Illuminates when the engine is running Caution Engine lubrication may be interrupted. This may result in damage to the engine and/or locking of the drive wheels. 1. Depress clutch. 2. Select neutral gear, set selector lever to N .
70 Instruments and controls Information displays Triple-Info-Display Displays time, outside temperature and date or Infotainment system (when it is on). When the ignition is off, the time, date and outside temperature can be displayed by briefly pressing one of the two buttons below the display.
Instruments and controls 71 Selecting with the multifunction control Turn the multifunction control to highlight menu items or commands and to select function areas. Press the multifunction control to select the highlighted item or confirm a command. To exit a menu, turn the multifunction control until Return or Main appear and select.
72 Instruments and controls System settings Press the Main button of the Infotainment system. Press the Settings button on the Infotainment system. For Infotainment system CD 30, no menu may be selected. Setting date and time Select menu item Time, Date from the Settings menu.
Instruments and controls 73 Selection is indicated by a 6 in front of the menu item. In systems with voice output, when the language setting of the display is changed the system will ask whether the announcement language should also be changed - see Infotainment system manual.
74 Instruments and controls Always day design: black text on light background. Always night design: white text on dark background. Selection is indicated by a o in front of the menu item. Ignition logic See Infotainment system manual. Vehicle messages Warning chimes When starting the engine or whilst driving ■ If seat belt is not fastened.
Lighting 75 Lighting Exterior lighting ............................ 75 Interior lighting ............................. 78 Lighting features .......................... 79 Exterior lighting Light switch Turn light switch: 7 = OFF 8 = Sidelights 9 = Headlights Control indicator 9 3 69.
76 Lighting Headlight range adjustment Manual headlight range adjustment Rotate the adjuster wheel to the required position to adjust the dipped beam range to vehicle loading and prevent dazzling.
Lighting 77 Turn and lane-change signals Lever up = right turn signal Lever down = left turn signal If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel moves back, the turn signal is automatically deactivated.
78 Lighting Interior lighting Instrument panel illumination control Brightness of the following lights can be adjusted when the exterior lights are on: ■ Instrument panel illumination ■ Info-Display ■ Illuminated switches and operation elements Turn thumb wheel k until the required brightness is obtained.
Lighting 79 Lighting features Centre console lighting Spotlight in interior mirror housing. Daylight-dependent, automatically regulated centre console lighting. Battery discharge protection Some consumers such as the interior lighting switch themselves off after approx.
80 Climate control Climate control Climate control systems ............... 80 Air vents ....................................... 82 Maintenance ................................ 82 Climate control systems Heating and ventilation system Controls for: ■ Temperature ■ Fan speed ■ Air distribution Heated rear window Ü 3 33.
Climate control 81 ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J . Air conditioning system In addition to the heating and ventilation system, the air conditioning system has: n = cooling 4 = air recirculation Heated seats ß 3 37.
82 Climate control Air vents Adjustable air vents At least one air vent must be open while cooling is on in order to prevent the evaporator from icing up due to lack of air movement. Set the direction of the air flow by turning the adjuster wheel from right to left and raise or lower the horizontal slats.
Climate control 83 Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when outside temperature is too low.
84 Driving and operating Driving and operating Driving hints ................................. 84 Starting and operating ................. 84 Engine exhaust ............................ 86 Manual transmission .................... 88 Manual transmission automated .
Driving and operating 85 Ignition switch positions 0 = Ignition off 1 = Steering wheel lock released, ignition off 2 = Ignition on, for diesel engine: preheating 3 = Starting Starting the engine Operate clutch and brake, automatic transmission in P or N .
86 Driving and operating Parking ■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface. ■ Always apply parking brake without pressing release button. Apply as firmly as possible on downhill or uphill slopes.
Driving and operating 87 consumption may be higher during this period. The emission of smells and smoke during this process is normal. Under certain driving conditions, e.
88 Driving and operating Caution Fuel grades other than those listed on pages 3 94, 3 143 could damage the catalytic converter or electronic components. Unburnt petrol will overheat and damage the catalytic converter. Therefore avoid excessive use of the starter, running the fuel tank dry and starting the engine by pushing or towing.
Driving and operating 89 Manual transmission automated The Easytronic transmission permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control. Transmission display Shows the mode and current gear. If the Winter programme is activated, T is illuminated.
90 Driving and operating Manual mode In manual mode, a gear can be selected manually by tapping the selector lever to the + or - position. The transmission display indicates the current gear. If the engine speed is too low the manual transmission automated will automatically shift to a lower gear even in Manual mode.
Driving and operating 91 Winter mode T Activate the Winter mode if you have problems starting off on a slippery road surface. Activation Press the T button.
92 Driving and operating If the cause of the fault is not a discharged battery, seek the assistance of a workshop. If the vehicle must be moved out of the flow of traffic, disengage the clutch as follows: 1. Apply parking brake and switch off ignition.
Driving and operating 93 ABS starts to regulate brake pressure as soon as a wheel shows a tendency to lock. The vehicle remains steerable, even during hard braking. ABS control is made apparent through a pulse in the brake pedal and the noise of the regulation process.
94 Driving and operating Brake assist If the brake pedal is depressed quickly and forcefully, maximum brake force is automatically applied (full braking). Maintain steady pressure on the brake pedal for as long as full braking is required. Maximum brake force is automatically reduced when the brake pedal is released.
Driving and operating 95 (high) has approx. 87 - 99 %. Biogas with the same methane content can also be used if it has been chemically prepared and desulphurised. Only use natural gas or biogas that complies with DIN 51624. Liquid gas or LPG must not be used.
96 Driving and operating Caution Wipe off any overflowing fuel immediately. Natural gas refuelling When filling with natural gas, remove the protective cap from the filler neck. 9 Warning Refuel only with a maximum output pressure of 250 bar. Use only temperature compensated filling stations.
Driving and operating 97 driving with approx. 2 / 3 . Cold starts and acceleration phases are also taken into consideration. The specification of CO 2 emission is also a constituent of the directive. The figures given must not be taken as a guarantee for the actual fuel consumption of a particular vehicle.
98 Driving and operating If the trailer starts snaking, drive more slowly, do not attempt to correct the steering and brake sharply if necessary. When driving downhill, drive in the same gear as if driving uphill and drive at a similar speed. Adjust tyre pressure to the value specified for full load 3 150.
Vehicle care 99 Vehicle care General Information ..................... 99 Vehicle checks ........................... 100 Bulb replacement ....................... 105 Electrical system ........................ 113 Vehicle tools ........................
100 Vehicle care ■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.g. anti-theft alarm system. Putting back into operation Following must be done if the vehicle is putting back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery.
Vehicle care 101 Pull the release lever and return it to its original position. Lift the safety catch upwards and open the bonnet. Air intake 3 82. Secure the bonnet support. Closing Before closing the bonnet, press the support into the holder. Lower the bonnet and allow it to drop into the catch.
102 Vehicle care When the engine oil level has dropped to the MIN mark, top up engine oil. We recommend to use the same engine oil that is filled in. The engine oil level must not exceed the MAX mark on the dipstick. Caution Overfilled engine oil must be drained or suctioned out.
Vehicle care 103 concentration checked and have the cause of the coolant loss remedied by a workshop. Washer fluid Fill with clean water mixed with a suitable quantity of washer fluid which contains antifreeze. For the correct mixing ratio refer to the washer fluid container.
104 Vehicle care Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point. Laying up the vehicle for more than 4 weeks can lead to battery discharge. Disconnect the clamp from the negative terminal of the vehicle battery.
Vehicle care 105 Wiper blade on the rear window Lift wiper arm. Disengage wiper blade as shown in illustration and remove. Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands.
106 Vehicle care Low beam 1. Rotate the cap anticlockwise and remove. 2. Push bulb on plug connector downward. 3. Remove bulb with connector from reflector housing. 4. Detach plug connector from bulb base. 5. Plug the plug onto the new bulb. 6. Insert the bulb with connector so that the lug engages in the recess in the reflector.
Vehicle care 107 3. Disengage spring clip from retainer by moving it forward and swivelling to the side. 4. Remove bulb from reflector housing. 5. When installing the new bulb, insert lugs in the reflector recesses. 6. Install spring clip, plug connector onto bulb.
108 Vehicle care 5. Attach connector to main beam bulb. 6. Place protective cover in position and close. Ellipsoidal headlights Headlights have separate systems for low beam (inner bulbs) and high beam (outer bulbs). Low beam 1. Remove protective cover by pressing the catch and pulling the cover downward and off.
Vehicle care 109 3. Insert bulb holder in reflector, rotate clockwise to engage. Fog lights Have bulbs replaced by a workshop. Front turn signal lights 1. Rotate bulb holder anti-clockwise to disengage. 2. Push bulb into socket slightly, rotate anti-clockwise, remove and renew bulb.
110 Vehicle care 2. Detach plug connector from bulb mounting. 3. Hold bulb housing from the outside; slacken two retaining nuts with the wheel bolt spanner 3 118 and unscrew by hand.
Vehicle care 111 2. Press bulb slightly towards spring clip and remove. 3. Insert new bulb. 4. Insert lamp insert and secure using a screwdriver. Interior lights Front courtesy light 1. Prise lamp out with a screwdriver. 2. Press bulb slightly towards spring clip and remove.
112 Vehicle care Front courtesy light, reading lights 1. Disengage lens using a screwdriver and remove. 2. Remove bulb and renew. 3. Mount lens and engage in position. Load compartment light 1. Prise lamp out with a screwdriver. 2. Press bulb slightly towards spring clip and remove.
Vehicle care 113 Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse. The fuse box is located in the engine compartment. Before replacing a fuse, turn off the respective switch and the ignition. A blown fuse can be recognised by its melted wire.
114 Vehicle care Disengage the cover, lift it upwards and remove. Fuse boxes of vehicles with engine Z13DTJ.
Vehicle care 115 No. Circuit 1 Central control unit 2 Engine control unit 3 Instruments, information display, light switch, horn, hazard warning lamps, immobiliser 4 Towing equipment, number plate lig.
116 Vehicle care No. Circuit 43 High beam (left) 44 High beam (right) 45 Ventilation fan 46 Engine control unit 47 Heated rear window 48 Starter 49 EPS 50 ABS 51 Petrol engine: manual transmission aut.
Vehicle care 117 No. Circuit 1 Central control unit 2 Engine control unit 3 Instruments, information display, light switch, horn, hazard warning lamps, immobiliser 4 Towing equipment, number plate lig.
118 Vehicle care No. Circuit 43 High beam (left) 44 High beam (right) 45 Ventilation fan 46 Engine control unit 47 Heated rear window 48 Starter 49 EPS 50 ABS 51 Petrol engine: manual transmission aut.
Vehicle care 119 The vehicle tools are secured to the jack with rubber bands. Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking.
120 Vehicle care Remove the valve cap key from the fuel filler flap and use it to unscrew the valve cap. Tyre pressure 3 150 and on the label on the inside of the fuel filler flap. The tyre pressure data refers to cold tyres. It applies to summer and winter tyres.
Vehicle care 121 Wheel covers Wheel covers and tyres that are factory approved for the respective vehicle and comply with all of the relevant wheel and tyre combination requirements must be used. If the wheel covers and tyres used are not factory approved, the tyres must not have a rim protection ridge.
122 Vehicle care 3. Remove the electrical connection cable and air hose from the stowage compartments on the underside of the compressor. 4. Screw the compressor air hose to the connection on the sealant bottle. 5. Fit the sealant bottle in the retainer on the compressor.
Vehicle care 123 6 bar. Then the pressure starts to drop. All of the sealant is pumped into the tyre. Then the tyre is inflated. 13. All of the sealant is pumped into the tyre. Then the tyre is inflated. 14. The prescribed tyre pressure should be obtained within 10 minutes.
124 Vehicle care Note The driving characteristics of the repaired tyre is severely affected, therefore have this tyre replaced. If unusual noise is heard or the compressor becomes hot, turn compressor off for at least 30 minutes. The built-in safety valve opens at a pressure of 7 bar.
Vehicle care 125 On some versions, the wheel cover is removed together with the wheel bolts. For wheel covers with visible wheel bolts, the cover can remain on the wheel. The retaining rings at the wheel bolts must not be removed. Alloy wheels: Disengage wheel bolt caps with a screwdriver and remove.
126 Vehicle care 4. Set the jack to the necessary height before positioning it directly below the jacking point in a manner that prevents it from slipping. Position the jack arm so that the jack claw grips the vertical web in the recess. The edge of the jack base must be planted firmly and vertically in line with the contact point.
Vehicle care 127 11. Stow the replaced wheel 3 121 and the vehicle tools 3 118. 12. Check the tyre pressure of the installed tyre and also the wheel bolt torque as soon as possible. Have the defective tyre renewed or repaired. Spare wheel Some vehicles are equipped with a tyre repair kit instead of a spare wheel.
128 Vehicle care If a full specification wheel is stowed, do not fit the spacer ring between the wheel and the vehicle underbody. 7. Change the wheel. 8. Lift the spare wheel holder, insert the safety cable. 9. Lift the spare wheel holder and engage in the catch.
Vehicle care 129 ■ A discharged battery can already freeze at a temperature of 0 °C. Defrost the frozen battery before connecting jump leads. ■ Wear eye protection and protective clothing when handling a battery. ■ Use a booster battery with the same voltage (12 Volts).
130 Vehicle care Towing Towing the vehicle Disengage the cover at the bottom and remove downwards. The towing eye is stowed with the vehicle tools 3 118. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or better still a tow rod – to the towing eye.
Vehicle care 131 Manual transmission automated 3 89. After towing, unscrew the towing eye and refit the cover. Towing another vehicle Attach a tow rope – or better still a tow rod – to the rear towing eye on the right side of the vehicle underbody, but never to the rear axle.
132 Vehicle care If using a car wash, comply with the car wash manufacturer's instructions. The windscreen wipers and rear window wiper must be switched off. Remove antenna and external accessories such as roof racks etc. If you wash your vehicle by hand, make sure that the insides of the wheel housings are also thoroughly rinsed out.
Vehicle care 133 After the underbody is washed, check the underbody and have it waxed if necessary. Bitumen/rubber materials could damage the PVC coating. Have underbody work carried out by a workshop. Before and after winter, wash the underbody and have the protective wax coating checked.
134 Service and maintenance Service and maintenance General information ................... 134 Recommended fluids, lubricants and parts ..............
Service and maintenance 135 Fixed service interval When service is due, InSP appears in the odometer display for approximately 10 seconds when the ignition is switched on. Have the next service performed by a workshop within one week or 500 km (whichever occurs first).
136 Service and maintenance aging control, whereas viscosity grade gives information on the oil's thickness over a temperature range. Dexos is the newest engine oil quality that provides optimum protection for gasoline and diesel engines. If it is unavailable, engine oils of other listed qualities have to be used.
Service and maintenance 137 Brake fluid should be stored in a sealed container to avoid water absorption. Ensure brake fluid does not become contaminated.
138 Technical data Technical data Vehicle identification .................. 138 Vehicle data ............................... 140 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is stamped on the identification plate and on the floor pan, under the floor covering, visible under a cover.
Technical data 139 In other versions the type plate is attached to the right spring strut dome in the engine compartment. Information on identification plate: 1 = Manufacturer 2 = Type approval number.
140 Technical data Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries ( except Belarus, Moldova, Russia, Serbia, Turkey) Only I.
Technical data 141 International service schedule Required engine oil quality All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Engine oil quality Petrol engines.
142 Technical data All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Engine oil quality Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (i.
Technical data 143 Engine data Sales designation 1.4 Twinport CNG 1.3 CDTI 1.7 CDTI Engine identifier code Z 14 XEP Z 16 YNG Z 13 DTJ Z 17 DTH Number of cylinders 4 4 4 4 Piston displacement [cm 3 ] 1.
144 Technical data Performance Engine Z 14 XEP Z 16 YNG Z 13 DTJ Z 17 DTH Maximum speed 2) [km/h] 5-speed manual transmission 164 165 152 3) 170 Manual transmission automated – – 152 3) – Fuel consumption - CO 2 - emissions Tyre width up to 185 mm Engine Z 14 XEP Z 13 DTJ Z 17 DTH Manual/manual transmission automated urban [l/100 km] 7.
Technical data 145 Engine Z 14 XEP Z 13 DTJ Z 17 DTH Manual/manual transmission automated urban [l/100 km] 8.1 / – 6.3 / 6.1 6.8 / – extra-urban [l/100 km] 5.
146 Technical data Vehicle weight Kerb weight Combo van Engine Manual transmission Manual transmission automated without/with air conditioning/climate control [kg] Z 14 XEP 1190 / 1350 – Z 16 YNG 13.
Technical data 147 Heavy accessories Accessories Folding sun roof Towing equipment Anti-lock braking system (ABS) Sliding door (front passenger´s side) Rear vent windows Load compartment grille Split.
148 Technical data Combo van Combo Load compartment height [mm] 1190 1190 Load compartment sill height [mm] 550 550 Opening width, tailgate min./max. [mm] 1030 / 1210 1030 / 1210 Opening height, tailgate min.
Technical data 149 Fuel tank Engine Z 14 XEP Z 13 DTJ Z 17 DTH Petrol/diesel, nominal capacity [l] 52 52 52 Engine oil Engine Z 16 YNG including Filter [l] 3.5 Between MIN and MAX [l] 1.0 Fuel tank Engine Z 16 YNG Natural gas, nominal capacity [kg] petrol, nominal capacity [l] 17.
150 Technical data Tyre pressures Combo van Comfort with up to 2 people and 100 kg luggage With full load Engine Tyres front rear front rear [ kPa/bar] ([psi]) [kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) Z 14 XEP 175/70 R 14, 9)10) 175/65 R 14, 185/55 R 15, 11)12) 185/60 R 15 240 / 2.
Technical data 151 Combo van Comfort with up to 2 people and 100 kg luggage With full load Engine Tyres front rear front rear [ kPa/bar] ([psi]) [kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) Z 16 YNG 185/60 R 15, 185/55 R 15 240 / 2.4 (35) 240 / 2.
152 Technical data Combo Comfort with up to 3 people With full load Engine Tyres front rear front rear [ kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) Z 14 XEP 175/70 R 14, 14) 175/65 R 14, 185/55 R 15, 15)16) 185/60 R 15, 17) 185/65 R 15, 195/45 R 16, 195/50 R 16 240 / 2.
Technical data 153 Combo Comfort with up to 3 people With full load Engine Tyres front rear front rear [ kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) Z 17 DTH 185/60 R 15, 185/55 R 15, 185/65 R 15, 195/50 R 16 240 / 2.4 (35) 240 / 2.
154 Technical data Combo Tramp / Arizona Comfort with up to 3 people With full load Engine Tyres front rear front rear [ kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) Z 14 XEP 185/60 R15 240 / 2.4 (35) 240 / 2.4 (35) 240 / 2.4 (35) 350 / 3.
Technical data 155 Towing hitch installation dimensions.
156 Customer information Customer information Vehicle data recording and privacy ....................................... 156 Vehicle data recording and privacy Event data recorders The vehicle has a number of sophisticated systems that monitor and control several vehicle data.
Customer information 157 Radio Frequency Identification (RFID) RFID technology is used in some vehicles for functions such as tyre pressure monitoring and ignition system security.
158 Index A Accessories and vehicle modifications ............................ 99 Adjustable air vents ..................... 82 Airbag and belt tensioners ........... 67 Airbag system .............................. 40 Air conditioning regular operation 83 Air conditioning system .
159 Engine coolant temperature gauge ....................................... 64 Engine data ............................... 143 Engine exhaust ............................ 86 Engine oil ................... 101, 135, 140 Engine oil pressure ...........
160 Mirror adjustment ........................... 8 Misted light covers ....................... 77 N New vehicle running-in ................ 84 Number plate light ..................... 110 O Odometer ..................................... 61 Oil, engine .
161 Tyre pressure ............................ 119 Tyre pressures ........................... 150 Tyre repair kit ............................. 121 U Underseat storage ....................... 48 Using this manual .......................... 3 V Vehicle dimensions .
162.
Een belangrijk punt na aankoop van elk apparaat Opel Combo (2012) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Opel Combo (2012) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Opel Combo (2012) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Opel Combo (2012) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Opel Combo (2012) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Opel Combo (2012) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Opel Combo (2012) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Opel Combo (2012) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
