Gebruiksaanwijzing /service van het product Meriva (2014) van de fabrikant Opel
Ga naar pagina of 237
OPEL Meriva Owner's Manual.
.
Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 20 Seats, restraints ........................... 35 Storage ........................................ 62 Instruments and controls .
2 Introduction Introduction.
Introduction 3 Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate.
4 Introduction Danger, Warnings and Cautions 9 Danger Text marked 9 Danger provides information on risk of fatal injury. Disregarding this information may endanger life. 9 Warning Text marked 9 Warning provides information on risk of accident or injury.
Introduction 5.
6 In brief In brief Initial drive information Vehicle unlocking Press button c to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, push the touchpad switch under the tailgate moulding. Radio remote control 3 21, Central locking system 3 22, Load compartment 3 26.
In brief 7 Seat backrests Pull lever, adjust inclination and release lever. Allow the seat to engage audibly. Seat position 3 37, Seat adjustment 3 37. Seat height Lever pumping motion up = seat higher down = seat lower Seat position 3 37, Seat adjustment 3 37.
8 In brief Head restraint adjustment Press release button, adjust height and engage. To adjust horizontally, pull the head restraint forwards. It engages in several positions. To return to its rearmost position, pull fully forwards and release. Head restraints 3 35.
In brief 9 Exterior mirrors Select the relevant exterior mirror and adjust it. Convex exterior mirrors 3 29, Electric adjustment 3 29, Folding exterior mirrors 3 29, Heated exterior mirrors 3 30. Steering wheel adjustment Unlock the lever, adjust the steering wheel, then engage the lever and ensure it is fully locked.
10 In brief Instrument panel overview.
In brief 11 1 Power windows ..................... 31 2 Exterior mirrors ..................... 29 3 Cruise control ..................... 148 4 Side air vents ...................... 130 5 Turn and lane-change signals, headlight flash, low beam and high beam .
12 In brief.
In brief 13 Exterior lighting Turn light switch: 7 = lights off 8 = sidelights 9 = low beam Automatic light control AUTO = automatic light control: exterior lighting is switched on and off automatical.
14 In brief Turn and lane-change signals lever up = right turn signal lever down = left turn signal Turn and lane-change signals 3 118, Parking lights 3 119. Hazard warning flashers Operated with the ¨ button. Hazard warning flashers 3 118. Horn Press j .
In brief 15 Washer and wiper systems Windscreen wiper 2 = fast 1 = slow P = interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Windscreen wiper 3 84, Wiper blade replacement 3 172.
16 In brief Push lever. Washer fluid is sprayed on the rear window and the wiper wipes a few times. Rear window wiper/washer 3 85. Climate control Heated rear window, heated exterior mirrors The heating is operated by pressing the Ü button. Heated rear window 3 33.
In brief 17 Transmission Manual transmission Reverse: with the vehicle stationary, wait 3 seconds after depressing clutch pedal then press the release button on the selector lever and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection.
18 In brief Starting the engine ■ Turn key to position 1 ■ move the steering wheel slightly to release the steering wheel lock ■ operate clutch and brake ■ automatic transmission in P or N ■.
In brief 19 ■ Lock the vehicle with button e on the radio remote control. ■ Activate the anti-theft alarm system 3 28. ■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface.
20 Keys, doors and windows Keys, doors and windows Keys, locks ................................... 20 Doors ........................................... 26 Vehicle security ............................ 27 Exterior mirrors ............................ 29 Interior mirrors .
Keys, doors and windows 21 Radio remote control Used to operate: ■ Central locking system ■ Anti-theft locking system ■ Anti-theft alarm system ■ Power windows The radio remote control has a range of approx. 5 metres. It can be restricted by external influences.
22 Keys, doors and windows Extend the key and open the unit. Replace the battery (battery type CR 2032), paying attention to the installation position. Close the unit and synchronise. Key with fixed key section Have the battery replaced by a workshop.
Keys, doors and windows 23 The setting can be changed in the menu Settings in the Info-Display. Vehicle personalisation 3 110. The setting can be saved for the key being used. Memorised settings 3 22. Locking Close doors, load compartment and fuel filler flap.
24 Keys, doors and windows Fault in radio remote control system Unlocking Manually unlock the driver's door by turning the key in the lock. Switch on the ignition and press the central locking button to unlock all doors, load compartment and fuel filler flap.
Keys, doors and windows 25 Automatic locking Automatic locking after driving off The vehicle is locked automatically when exceeding a speed of 4 km/h. Opening from outside is not possible. Additionally, opening of the rear doors from inside is not possible when the vehicle speed is above 4 km/h.
26 Keys, doors and windows 9 Warning Use the child locks whenever children are occupying the rear seats. Using a key or suitable screwdriver, turn the child lock in the rear door to the horizontal position. The green LED will extinguish. The door cannot be opened from the inside.
Keys, doors and windows 27 Closing Use one of the interior handles. Do not push the touchpad switch under the moulding whilst closing as this will unlock the tailgate again. Central locking system 3 22. General hints for operating tailgate 9 Danger Do not drive with the tailgate open or ajar, e.
28 Keys, doors and windows Activating Press e on the radio remote control twice within 10 seconds. Anti-theft alarm system The anti-theft alarm system incorporates and is operated in conjunction with the anti-theft locking system. It monitors: ■ Doors, tailgate, bonnet ■ Ignition Unlocking the vehicle deactivates both systems simultaneously.
Keys, doors and windows 29 Immobiliser The system is part of the ignition switch and checks whether the vehicle is allowed to be started with the key being used. The immobiliser is activated automatically after the key has been removed from the ignition switch.
30 Keys, doors and windows Heated mirrors Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. Interior mirrors Manual anti-dazzle To reduce dazzle, adjust the lever on the underside of the mirror housing.
Keys, doors and windows 31 Windows Windscreen Heat-reflecting windscreen The heat-reflecting windscreen has a coating which reflects solar radiation. Also data signals, e.g. from toll stations, might be reflected. The marked areas on the windscreen are not covered with the coating.
32 Keys, doors and windows Operate the switch for the respective window by pushing to open or pulling to close. Pushing or pulling gently to the first detent: window moves up or down as long as switch is operated. Pushing or pulling firmly to the second detent and then releasing: window moves up or down automatically with safety function enabled.
Keys, doors and windows 33 Initialising the power windows If the windows cannot be closed automatically (e.g. after disconnecting the vehicle battery), a warning message or a warning code is displayed in the Driver Information Centre. Vehicle messages 3 104.
34 Keys, doors and windows Roof Moonroof Do not affix any stickers to the roof. Do not cover the vehicle using a tarpaulin. Sunblind The sunblind is electrically operated. Press button G or H gently to the first detent: the sunblind is opened or closed as long as the switch is operated.
Seats, restraints 35 Seats, restraints Head restraints ............................ 35 Front seats ................................... 37 Rear seats ................................... 42 Seat belts ..................................... 45 Airbag system .
36 Seats, restraints Horizontal adjustment To adjust horizontally, pull the head restraint forwards. It engages in several positions. To return to its rearmost position, pull fully forwards and release.
Seats, restraints 37 Front seats Seat position 9 Warning Only drive with the seat correctly adjusted. ■ Sit with buttocks as far back against the backrest as possible. Adjust the distance between the seat and the pedals so that legs are slightly angled when pressing the pedals.
38 Seats, restraints Seat positioning Pull handle, slide seat, release handle. Seat backrests Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly.
Seats, restraints 39 Seat inclination Lever pumping motion up = front end higher down = front end lower Lumbar support Adjust lumbar support using the four- way switch to suit personal requirements. Moving support up and down: push switch up or down. Increasing and decreasing support: push switch forwards or backwards.
40 Seats, restraints Armrest Detachable armrest The armrest contains a storage compartment. Storage compartment 3 64. Installing armrest on the centre console Press the rear button and insert the rear guide pins into the upper guide rails. Release the button.
Seats, restraints 41 Moving armrest Pull the front handle slightly and move the armrest to the desired position. Release the handle. Move the armrest until it engages audibly. If a cupholder is installed in the lower guide rail, make sure that the frame of the cupholder is in the initial position.
42 Seats, restraints Rear seats Seat adjustment 9 Warning Only drive with the outer seats engaged in the guide rails. 9 Warning Never adjust seats while driving as they could move uncontrollably. The rear outboard seats can be individually moved forwards or backwards.
Seats, restraints 43 Pull handle and slide the seat transversely backward into position 1 . The seat is automatically guided inward. Release handle and allow seat to engage in position. Moving seats to position 2 Pull handle and slide the seat transversely forwards into position 2 .
44 Seats, restraints Insert the hooks of the adapter into the recesses of the seatback and push the adapter forwards. Lock the adapter by turning the ignition key clockwise in the lock. The adapter is locked properly when the green mark is visible. Mount the armrest on the adapter.
Seats, restraints 45 Removing the adapter Unlock the adapter by turning the ignition key anticlockwise in the lock. The adapter is unlocked when the red mark is visible. Push the adapter rearward and remove. Seat belts The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the sitting position.
46 Seats, restraints 9 Warning Incorrect handling (e.g. removal or fitting of belts) can trigger the belt pretensioners. Deployment of the belt pretensioners is indicated by continuous illumination of control indicator v 3 94. Triggered belt pretensioners must be replaced by a workshop.
Seats, restraints 47 Height adjustment 1. Pull belt out slightly. 2. Press button. 3. Adjust height and engage. Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Do not adjust while driving. Removing seat belt To release belt, press red button on belt buckle.
48 Seats, restraints Click bottom latch plate into right- hand buckle ( 1 ) at centre seat. Remove top latch plate from retainer, guide over shoulder and lap area with belt (do not twist) and click into left- hand buckle ( 2 ) at centre seat. To remove the seat belt, first press the button on the left-hand buckle ( 2 ) and remove top latch plate.
Seats, restraints 49 Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision.
50 Seats, restraints sous peine d'infliger des BLESSURES GRAVES, voire MORTELLES à l'ENFANT. ES: NUNCA utilice un sistema de retención infantil orientado hacia atrás en un asiento protegido por un AIRBAG FRONTAL ACTIVO. Peligro de MUERTE o LESIONES GRAVES para el NIÑO.
Seats, restraints 51 TR: Arkaya bakan bir çocuk emniyet sistemini KESİNLİKLE önünde bir AKTİF HAVA YASTIĞI ile korunmakta olan bir koltukta kullanmayınız.
52 Seats, restraints AKTĪVU DROŠĪBAS SPILVENU, jo pretējā gadījumā BĒRNS var gūt SMAGAS TRAUMAS vai IET BOJĀ. ET: ÄRGE kasutage tahapoole suunatud lapseturvaistet istmel, mille ees on AKTIIVSE TURVAPADJAGA kaitstud iste, sest see võib põhjustada LAPSE SURMA või TÕSISE VIGASTUSE.
Seats, restraints 53 Side airbag system The side airbag system consists of an airbag in each front seat backrest. This can be identified by the word AIRBAG . The side airbag system is triggered in the event of a side impact of a certain severity. The ignition must be switched on.
54 Seats, restraints 9 Warning Keep the area in which the airbag inflates clear of obstructions. The hooks in the roof frame are only suitable for hanging up light articles of clothing, without coat hangers.
Seats, restraints 55 If the control indicator V illuminates for approx. 60 seconds after the ignition is switched on, the front passenger airbag system will inflate in the event of a collision. If both control indicators are illuminated at the same time, there is a system failure.
56 Seats, restraints Three-point seat belt Top-Tether When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system. Always comply with local or national regulations.
Seats, restraints 57 When the child restraint system is not in use, secure the seat with a seat belt or remove it from the vehicle. Note Do not stick anything on the child restraint systems and do not cover them with any other materials. A child restraint system which has been subjected to stress in an accident must be replaced.
58 Seats, restraints Child restraint installation locations Permissible options for fitting a child restraint system Weight and age class On front passenger seat On rear outboard seats On rear centre seat activated airbag deactivated airbag Group 0: up to 10 kg or approx.
Seats, restraints 59 Permissible options for fitting an ISOFIX child restraint system Weight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat Group 0: up to 10 kg or approx. 10 months E ISO/R1 X IL 1 X Group 0+: up to 13 kg or approx.
60 Seats, restraints IL = Suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories. The ISOFIX restraint system must be approved for the specific vehicle type.
Seats, restraints 61 ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle ISOFIX child restraint system positions are marked in the table by IL. ISOFIX mounting brackets are indicated by a label on the backrest.
62 Storage Storage Storage compartments ................ 62 Load compartment ....................... 74 Roof rack system ......................... 80 Loading information ..................... 80 Storage compartments 9 Warning Do not store heavy or sharp objects in the storage compartments.
Storage 63 Detachable cupholder A cupholder can be attached either to the upper or lower guide rails in the front console. Fold the frame out of initial position before using.
64 Storage Cupholder on armrest adapter A further cupholder is integrated to the armrest adapter of the rear centre seat. Armrest adapter 3 43. Front storage A storage compartment is located next to the steering wheel. Underseat storage Lift drawer at recessed edge and pull out.
Storage 65 Rear carrier system The rear carrier system (Flex-Fix system) allows bicycles to be attached to a pull-out carrier integrated into the vehicle floor. The transportation of other objects is not permitted. The maximum load of the rear carrier system is 40 kg.
66 Storage will not engage correctly, do not fit objects to the system and slide the system back. Seek the assistance of a workshop. Install the tail lamps First remove the rear tail lamp ( 1 ), then the front ( 2 ) tail lamp from the recesses. Open out the lamp support on the back of the tail lamp completely.
Storage 67 Lock the rear carrier system Swivel the right clamping lever ( 1 ) first, followed by the left clamping lever ( 2 ), until a resistance is noticeable. The rear carrier system is locked when the clamping levers are swivelled by approx. 50°.
68 Storage Unfold pedal crank recesses Fold one or both pedal crank recesses upwards until the diagonal support engages. Remove the pedal crank mounts from the pedal crank recesses. Adapting the rear carrier system to a bicycle Press the release lever and withdraw the wheel recesses.
Storage 69 Push the release lever on the strap retainer and remove the strap retainer. Prepare the bicycle for attachment Note The maximum width for the pedal crank is 38.3 mm and the maximum depth is 14.4 mm. Rotate the left pedal (without a chain cog) vertically downwards.
70 Storage If the bicycle has curved pedal cranks, screw in the pedal crank unit all the way (position 1 ). Put on the bicycle. The pedal crank here must be placed in the pedal crank recess opening as shown in the illustration. Caution Make sure that the pedal does not touch the surface of the rear end carrier.
Storage 71 Place the wheel recesses so that the bicycle is roughly horizontal. Here, the distance between the pedals and the tailgate should be at least 5 cm. Both bicycle tyres must be in the wheel recesses. Caution Make sure to pull out the wheel recesses as far as necessary to have both bicycle tyres placed in the recesses.
72 Storage The settings for the wheel recesses and on the rotary lever on the pedal crank recess should be noted and saved for each bicycle. Correct presetting will facilitate refitting of the bicycle. Note It is recommended to attach a warning sign at the rearmost bicycle to increase visibility.
Storage 73 Press release lever and slide in wheel recesses all the way as far as they will go. Disengage the locking lever on the diagonal support and fold both pedal crank recesses down. 9 Warning Risk of pinching. Remove number plate and fold down the number plate holder.
74 Storage Push the release lever up and hold. Lift the system slightly and push it into the bumper until it engages. Release lever must return to original position. 9 Warning If the system cannot be correctly engaged, please seek the assistance of a workshop.
Storage 75 Pull the handle on the front side of the backrest and fold down the backrest onto the seat cushion. The seat is lowered automatically. The backrests can also be folded from the load compartment. Pull the handle on the back side of the backrest and fold down the backrest.
76 Storage Removing the cover Unhook retaining straps from tailgate. Lift cover at the rear and push it upwards at the front. Remove the cover. Stowing the cover Unhook retaining straps from tailgate. Lift cover at the rear and push it upwards out of the side guides at the front.
Storage 77 Double load-bay floor The double load-bay floor can be inserted in the load compartment in two positions: ■ directly above the cover for the spare wheel well or the rear floor cover, ■ in the upper openings in the load compartment. To remove, lift the load-bay floor using the recess and pull backwards.
78 Storage Installation There are two installation openings in the roof frame: suspend rod of net at one side, push to the front and engage. Extend rod, suspend at other side, push to the front and engage. Suspend hooks of net tensioning belts in lashing eyes in the floor behind the front seats.
Storage 79 Roll the upper net rod down to approximately over the middle. Place the upper net rod over the tensioning straps next to the lower net rod. The hooks on the upper net rod must point away from the lower net rod. Fasten Velcro tape tightly about the net next to the length adjusters.
80 Storage Depending on the vehicle, a box is located under the driver's seat. Pull handle and fold down the cover. Maximum load: 1.5 kg. Roof rack system Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended.
Storage 81 ■ Use the hook at the left sidewall of the load compartment for hanging up carrier bags. Pull out the hook. Maximum load: 3 kg. ■ Secure loose objects in the load compartment to prevent them from sliding. ■ When transporting objects in the load compartment, the backrests of the rear seats must not be angled forward.
82 Instruments and controls Instruments and controls Controls ....................................... 82 Warning lights, gauges and indi‐ cators ........................................... 89 Information displays ................... 100 Vehicle messages .
Instruments and controls 83 Heated steering wheel Activate heating by pressing * button. Activation is indicated by the LED in the button. The recommended grip areas of the steering wheel are heated quicker and to a higher temperature than the other areas.
84 Instruments and controls Windscreen wiper/washer Windscreen wiper 2 = fast 1 = slow P = interval wiping § = off For a single wipe when the windscreen wiper is off, press the lever down. Do not use if the windscreen is frozen. Switch off in car washes.
Instruments and controls 85 Adjustable sensitivity of the rain sensor Turn the adjuster wheel to adjust the sensitivity: low sensi‐ tivity = turn adjuster wheel downwards high sensi‐ tivity = turn adjuster wheel upwards Keep the sensor free from dust, dirt and ice.
86 Instruments and controls Push lever. Washer fluid is sprayed onto the rear window and the wiper wipes a few times. Do not use if the windscreen is frozen. Switch off in car washes. The rear window wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged.
Instruments and controls 87 Time and date settings CD 300/CD 400/CD400plus Press the CONFIG button. The menu Settings is displayed. Select Time & Date . Selectable setting options: ■ Set time : Changes the time shown on the display. ■ Set date : Changes the date shown on the display.
88 Instruments and controls Adjust all settings. Set date To adjust the time settings, select the Set Date menu item. Turn the multifunction knob to adjust the first setting. Press the multifunction knob to confirm the input. The coloured background moves to the next setting.
Instruments and controls 89 Cigarette lighter The cigarette lighter is located in the front console. Press in cigarette lighter. It switches off automatically once the element is glowing. Pull out lighter. Ashtrays Caution To be used only for ash and not for combustible rubbish.
90 Instruments and controls Odometer The bottom line displays the recorded distance in km. Trip odometer The top line displays the recorded distance since the last reset. To reset, press the SET/CLR button on the turn signal lever for a few seconds 3 100.
Instruments and controls 91 Because of the fuel remaining in the tank, the top-up quantity may be less than the specified tank capacity. Fuel selector Pressing button LPG switches between petrol and liquid gas operation. The LED 1 status shows the current operating mode.
92 Instruments and controls In the Uplevel-Display the remaining oil life duration is displayed in the Vehicle Information Menu . In the Midlevel-Display the remaining engine oil life duration is displayed by the control indicator I . The ignition must be switched on, with the engine not running.
Instruments and controls 93 Control indicators in the instrument cluster.
94 Instruments and controls Control indicators in the centre console Turn signal O illuminates or flashes green. Illuminates briefly The parking lights are switched on. Flashes A turn signal or the hazard warning flashers are activated. Rapid flashing: failure of a turn signal light or associated fuse, failure of turn signal light on trailer.
Instruments and controls 95 9 Warning Have the cause of the fault remedied immediately by a workshop. Belt pretensioners, airbag system 3 45, 3 49. Airbag deactivation V illuminates yellow. Illuminates for approx. 60 seconds after the ignition is switched on.
96 Instruments and controls Brake and clutch system Brake and clutch fluid level R illuminates red. The brake and clutch fluid level is too low 3 169. 9 Warning Stop. Do not continue your journey. Consult a workshop. Operate pedal - illuminates or flashes yellow.
Instruments and controls 97 Upshift [ illuminates green or is shown as a symbol in the Driver Information Centre with Uplevel-Display when upshifting is recommended for fuel saving reasons. Variable effort steering c illuminates yellow. Fault in variable effort steering system.
98 Instruments and controls Continue driving until % extinguishes. If possible do not allow engine speed to drop below 2000 rpm. Illuminates The diesel particle filter is full. Start cleaning process as soon as possible. Flashes The maximum filling level of the filter is reached.
Instruments and controls 99 Additionally a warning message is displayed on vehicles with Midlevel- and Uplevel-Display. Catalytic converter 3 139. Bleeding the diesel fuel system 3 172. Immobiliser d flashes yellow. Fault in the immobiliser system. The engine cannot be started.
100 Instruments and controls 9 Warning Stop your journey immediately! Follow the instructions as described in paragraph "Fault in the automatic locking system" before continuing your journey 3 25.
Instruments and controls 101 Selecting menus and functions The menus and functions can be selected via the buttons on the turn signal lever. Press the MENU button to switch between the menus or to return from a submenu to the next higher menu level. Turn the adjuster wheel to highlight a menu option or to set a numeric value.
102 Instruments and controls ◆ Unit1 : Great Britain ◆ Unit2 : United States ◆ Unit3 : Europe ■ Tire Pressure System : 3 190 ■ Remaining Oil Life : 3 91 ■ Speed Warning : If exceeding the .
Instruments and controls 103 Graphic-Info-Display indicates: ■ time 3 86 ■ outside temperature 3 86 ■ date 3 86 ■ Infotainment system, see description for Infotainment system in the Infotainme.
104 Instruments and controls Selecting with the Infotainment system Select a function via the Infotainment system buttons. The menu of the selected function is displayed.
Instruments and controls 105 Vehicle messages on the Midlevel-Display The vehicle messages are displayed as code numbers. No. Vehicle message 2 No radio remote control detected, depress clutch pedal for a restart 3 Engine coolant level low 4 Air conditioning off 5 Steering wheel is locked No.
106 Instruments and controls No. Vehicle message 55 Diesel particle filter is full 3 138 56 Tyre pressure imbalance on front axle 57 Tyre pressure imbalance on rear axle 58 Tyres without TPMS sensors .
Instruments and controls 107 The system displays messages regarding the following topics: ■ Fluid levels ■ Anti-theft alarm system ■ Brakes ■ Drive systems ■ Ride control systems ■ Cruise .
108 Instruments and controls 1. Switch off immediately any electrical consumers which are not required for a safe ride, e.g. seat heating, heated rear window or other main consumers. 2. Charge the vehicle battery by driving continuously for a while or by using a charging device.
Instruments and controls 109 The information of the two trip computers can be reset separately, making it possible to display different trip distances. To reset, press the SET/CLR button for a few seconds. On vehicles with reset knob, hold the reset knob depressed for a few seconds with the ignition on.
110 Instruments and controls Vehicle personalisation The vehicle's behaviour can be personalised by changing the settings in the Info-Display. Some of the personal settings for different drivers can be memorised individually for each vehicle key.
Instruments and controls 111 Vehicle settings ■ Climate and air quality Auto fan speed : Modifies the level of the cabin airflow of the climate control in automatic mode. Climate control mode : Controls the state of the cooling compressor when the vehicle is started.
112 Instruments and controls Turn the multifunction knob to scroll upwards or downwards in the list. Press the multifunction knob (Navi 950 / Navi 650: press the outer ring) to select a menu item.
Instruments and controls 113 Personalisation by Driver : Activates or deactivates the personalisation function. Auto Reverse Gear Wiper : Activates or deactivates automatically switching on of the rear window wiper when reverse gear is engaged. ■ Collision Detection Systems Park Assist : Activates or deactivates the ultrasonic sensors.
114 Lighting Lighting Exterior lighting .......................... 114 Interior lighting ........................... 120 Lighting features ........................ 121 Exterior lighting Light switch Turn light switch: 7 = lights off 8 = sidelights 9 = low beam Control indicator 8 3 99.
Lighting 115 In the Driver Information Centre with Uplevel-Display, the current status of the automatic light control is displayed. When switching on the ignition, automatic light control is active. When low beam is on, 8 lights up. Control indicator 8 3 99.
116 Lighting Headlight range adjustment Manual headlight range adjustment To adapt headlight range to the vehicle load to prevent dazzling: turn thumb wheel ? to required position. 0 = front seats occupied 1 = all seats occupied 2 = all seats occupied and load compartment laden 3 = driver's seat occupied and load compartment laden.
Lighting 117 Vehicles with Adaptive Forward Lighting 1. Key in ignition switch. 2. Pull turn signal lever and hold (headlight flash). 3. Switch on ignition. 4. After approx. 5 seconds the control indicator f starts flashing and an acoustic signal sounds.
118 Lighting Hazard warning flashers Operated with the ¨ button. In the event of an accident with airbag deployment the hazard warning flashers are activated automatically.
Lighting 119 Rear fog lights Operated with the r button. Light switch in position AUTO : switching on rear fog light will switch the low beam on automatically. Light switch in position 8 : rear fog light can only be switched on with front fog lights. The vehicle rear fog light is deactivated when towing.
120 Lighting Interior lighting Instrument panel illumination control Brightness of the following lights can be adjusted when the exterior lights are on: ■ Instrument panel illumination ■ Info-Display ■ Illuminated switches and operation elements Turn thumb wheel A until the required brightness is obtained.
Lighting 121 Reading lights Operated with s and t buttons in front and rear courtesy lights. Sunvisor lights Illuminate when the cover is opened. Lighting features Centre console lighting Spotlight incorporated in the interior lighting comes on when the low beam is switched on.
122 Lighting Switching on 1. Switch off ignition. 2. Remove ignition key. 3. Open driver's door. 4. Pull turn signal lever. 5. Close driver's door.
Climate control 123 Climate control Climate control systems ............. 123 Air vents ..................................... 130 Maintenance .........
124 Climate control Note If the settings for demisting and defrosting are selected, an Autostop will be inhibited. If the settings for demisting and defrosting are selected while the engine is in an Autostop, the engine will restart automatically. Stop-start system 3 136.
Climate control 125 ■ Switch on cooling n . ■ Switch on air recirculation system 4 . ■ Press air distribution switch M . ■ Set temperature control to coldest level.
126 Climate control Heated rear window Ü 3 33, Heated seats ß 3 41, Heated steering wheel * 3 83. Climate control settings are shown on the Graphic-Info-Display, or depending on the version, on Colour- Info-Display. Setting modifications are briefly popped-up in both displays, superimposed over the currently displayed menu.
Climate control 127 If the minimum temperature Lo is set, the climate control system runs at maximum cooling, if cooling n is switched on. If the maximum temperature Hi is set, the climate control system runs at maximum heating.
128 Climate control Fan speed Z Press lower button to decrease or upper button to increase fan speed as shown in the illustration. The fan speed is indicated by the number of segments in the display. Pressing the lower button longer: fan and cooling are switched off.
Climate control 129 If no cooling or drying is required, switch off the cooling system for fuel saving reasons. Activated cooling might inhibit Autostops. Stop-start system 3 136. Depending on the vehicle equipment, the display will indicate AC when cooling is actived or Eco when the cooling is deactivated.
130 Climate control Demisting and defrosting the windows V ■ Press button V : fan automatically switches to higher speed, the air distribution is directed towards the windscreen. ■ Switch on cooling n . ■ Set temperature control to warmest level.
Climate control 131 Direct the flow of air by tilting and swivelling the slats. To close the vent, turn the adjuster wheel to the left. 9 Warning Do not attach any objects to the slats of the air vents. Risk of damage and injury in case of an accident.
132 Climate control ■ Functionality and pressure test ■ Heating functionality ■ Leakage check ■ Check of drive belts ■ Cleaning of condenser and evaporator drainage ■ Performance check.
Driving and operating 133 Driving and operating Driving hints ............................... 133 Starting and operating ............... 134 Engine exhaust .......................... 138 Automatic transmission .............. 140 Manual transmission ..
134 Driving and operating Starting and operating New vehicle running-in Do not brake unnecessarily hard for the first few journeys. During the first drive, smoke may occur because of wax and oil evaporating off the exhaust system. Park the vehicle in the open for a while after the first drive and avoid inhaling the fumes.
Driving and operating 135 Diesel engine: turn the key to position 2 for preheating until control indicator ! extinguishes. Turn the key briefly to position 3 and release: an automatic procedure operates the starter with a short delay as long as the engine is running, see Automatic Starter Control.
136 Driving and operating Stop-start system The stop-start system helps to save fuel and to reduce the exhaust emissions. When conditions allow, it switches off the engine as soon as the vehicle is at a low speed or at a standstill, e.g. at a traffic light or in a traffic jam.
Driving and operating 137 ■ The stop-start system is not manually deactivated ■ the bonnet is fully closed ■ the driver's door is closed or the driver's seat belt is fastened ■ the v.
138 Driving and operating ■ the engine temperature is too low ■ the vehicle battery is discharged ■ the brake vacuum is not sufficient ■ the vehicle starts to move ■ the climate control syst.
Driving and operating 139 take up to 25 minutes. Typically it needs between 7 and 12 minutes. Autostop is not available and fuel consumption may be higher during this period. The emission of smells and smoke during this process is normal. Under certain driving conditions, e.
140 Driving and operating rectified by a workshop as soon as possible. In an emergency, driving can be continued for a short period, keeping vehicle speed and engine speed low. Automatic transmission The automatic transmission permits automatic gearshifting (automatic mode) or manual gearshifting (manual mode).
Driving and operating 141 Without brake pedal applied, the control indicator j illuminates. If the selector lever is not in P when the ignition is switched off, the control indicator j and P flash. To engage P or R , press the release button. The engine can only be started with the lever in position P or N .
142 Driving and operating In manual mode no automatic shifting to a higher gear takes place at high engine revolutions. Electronic driving programmes ■ Following a cold start, the operating temperature programme increases engine speed to quickly bring the catalytic converter to the required temperature.
Driving and operating 143 4. Move the selector lever trim to the left. Take care that the plug and the wiring harness at the bottom are not damaged. 5. Insert a screwdriver into the opening as far as it will go and move the selector lever out of P or N .
144 Driving and operating Brakes The brake system comprises two independent brake circuits. If a brake circuit fails, the vehicle can still be braked using the other brake circuit. However, braking effect is achieved only when the brake pedal is depressed firmly.
Driving and operating 145 Parking brake Electric parking brake Applying when vehicle is stationary Pull switch m for approx. one second, the electric parking brake operates automatically with an adequate force. For maximum force, e.g. parking with trailer or on inclines, pull switch m twice.
146 Driving and operating Control indicator m flashes: electric parking brake is not fully applied or released. When continuously flashing, release electric parking brake and retry applying. Brake assist If the brake pedal is depressed quickly and forcefully, maximum brake force is automatically applied (full braking).
Driving and operating 147 9 Warning Do not let this special safety feature tempt you into taking risks when driving. Adapt speed to the road conditions. Control indicator b 3 97. Deactivation TC can be switched off when spinning of drive wheels is required: press button b briefly.
148 Driving and operating ESC is reactivated by pressing the b button again. If the TC system was previously disabled, both TC and ESC are reactivated.
Driving and operating 149 Switching on Press rocker switch m at the upper end, control indicator m illuminates white. Activation Accelerate to the desired speed and turn thumb wheel to SET/- , the current speed is stored and maintained. Control indicator m illuminates green.
150 Driving and operating The system consists of four ultrasonic parking sensors in the rear bumper. If the vehicle is equipped with a front parking assist, the system consists of four additional ultrasonic parking sensors in the front bumper. Control indicator r 3 97.
Driving and operating 151 such obstacles leave the detection area of the sensors during approach of the vehicle, a continuous warning tone will sound. Caution Performance of the sensors can be reduced when sensors are covered, e.g. by ice or snow. Performance of the parking assist systems can be reduced due to heavy loading.
152 Driving and operating Functionality The camera is mounted in the tailgate handle and has a viewing angle of 130°. Due to the high position of the camera the rear bumper can be seen on the display as a guide to position. The area displayed by the camera is limited.
Driving and operating 153 Display settings Brightness can be set with the up/ down buttons of the multifunction knob. Contrast can be set with left/right buttons of the multifunction knob. Deactivation The camera is deactivated when a certain forward speed is exceeded or if reverse gear is not engaged for approx.
154 Driving and operating Caution Use of fuel that does not comply to EN 228 or E DIN 51626-1 or equivalent can lead to deposits or engine damage and loss of warranty. Caution Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage.
Driving and operating 155 Pressing the LPG button switches between petrol and liquid gas operation as soon as the required parameters (coolant temperature, gas temperature and minimum engine speed) have been reached.
156 Driving and operating Turn the thumb wheel clockwise. If no further gas odour is perceptible when the manual shut-off valve is closed, the vehicle can be used in petrol mode. If the gas odour persists, do not start the engine. Have the cause of the fault remedied by a workshop.
Driving and operating 157 The fuel filler flap can only be opened if the vehicle is unlocked. Pull flap at the recess and open. To open, turn the cap slowly to the left. The fuel filler cap can be retained in the bracket on the fuel filler flap. For refuelling, fully insert the pump nozzle and switch it on.
158 Driving and operating Screw the required adapter hand- tight onto the filler neck. ACME Adapter: Screw the nut of the filling nozzle onto the adapter. Press locking lever on filler nozzle down. DISH (Italy) filler neck: Place the filler nozzle into the adapter.
Driving and operating 159 ACME adapter: Belgium, Germany, Ireland, Luxembourg, Switzerland Bayonet adapter: Netherlands, Norway, Spain, United Kingdom EURO adapter: Spain DISH (Italy) adapter: Bosnia-.
160 Driving and operating Fuel consumption data and CO 2 emission data are determined according to regulation R (EC) No. 715/2007 (in the version respectively applicable), taking into consideration the vehicle weight in running order, as specified by the regulation.
Driving and operating 161 The permissible trailer loads are vehicle and engine-dependent maximum values which must not be exceeded. The actual trailer load is the difference between the actual gross weight of the trailer and the actual coupling socket load with the trailer coupled.
162 Driving and operating Stowage of the detachable coupling ball bar The bag with the coupling ball bar is stowed in the rear stowage compartment on the floor. Run the strap through the lashing eye and tighten the strap to secure the bag. Fitting the detachable coupling ball bar Disengage and fold down the socket.
Driving and operating 163 Pull out rotary knob and turn clockwise as far as it will go. Inserting the coupling ball bar Insert the tensioned coupling ball bar in the opening and push firmly upwards until it audibly engages. The rotary handle snaps back into its original position resting against the coupling ball bar without a gap.
164 Driving and operating ■ The coupling ball bar must be firmly engaged in the opening. ■ The coupling ball bar must be locked and the key removed. 9 Warning Towing a trailer is permitted only when a coupling ball bar is fitted correctly. If the coupling ball bar does not engage correctly, seek the assistance of a workshop.
Vehicle care 165 Vehicle care General Information ................... 165 Vehicle checks ........................... 166 Bulb replacement ....................... 173 Electrical system ........................ 183 Vehicle tools ........................
166 Vehicle care ■ Open the bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery.
Vehicle care 167 9 Danger The ignition system uses extremely high voltage. Do not touch. Bonnet Opening Pull the release lever and return it to its original position. Press the safety catch and open the bonnet. Secure the bonnet support. If the bonnet is opened during an Autostop, the engine will be restarted automatically for safety reasons.
168 Vehicle care Different dipsticks are used depending on engine variant. When the engine oil level has dropped to the MIN mark, top up engine oil. We recommend the use of the same grade of engine oil that was used at last change. The engine oil level must not exceed the MAX mark on the dipstick.
Vehicle care 169 If the cooling system is cold, the coolant level should be above the filling line mark. Top up if the level is low. 9 Warning Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly. To top up use a 1:1 mixture of approved coolant concentrate mixed with clean tap water.
170 Vehicle care The brake fluid level must be between the MIN and the MAX marks. When topping up, ensure maximum cleanliness as contamination of the brake fluid can lead to brake system malfunctions. Have the cause of the loss of brake fluid remedied by a workshop.
Vehicle care 171 In vehicles with stop-start system, ensure to have the AGM (Absorptive Glass Mat) battery replaced with an AGM battery again. An AGM battery can be identified by the label on the battery. We recommend the use of an original Opel vehicle battery.
172 Vehicle care Meaning of symbols: ■ No sparks, naked flames or smoking. ■ Always shield eyes. Explosive gases can cause blindness or injury. ■ Keep the vehicle battery out of reach of children. ■ The vehicle battery contains sulphuric acid which could cause blindness or serious burn injuries.
Vehicle care 173 Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base. Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. Replace headlight bulbs from within the engine compartment.
174 Vehicle care 3. Detach the bulb from the bulb holder and replace the bulb. 4. Insert the bulb holder into the reflector. 5. Fit the cap and rotate clockwise. High beam 1. Rotate the cap 2 anticlockwise and remove it. 2. Detach the plug from the bulb.
Vehicle care 175 2. Detach bulb from the bulb holder and replace it. 3. Insert the bulb holder into the reflector and rotate clockwise. Sidelight/Daytime running light with LEDs On another version sidelight and daytime running lights are designed as LEDs.
176 Vehicle care 2. Rotate the bulb holder clockwise to disengage. Withdraw the bulb holder from the reflector. 3. Disengage the bulb holder from the plug connector by pressing the retaining lug. 4. Replace the bulb and connect bulb holder with the plug connector.
Vehicle care 177 Sidelight/Daytime running light Sidelight and daytime running lights are designed as LEDs. In case of failure, have LEDs replaced by a workshop. Fog lights The bulbs are accessible from the underside of the vehicle. 1. Turn the bulb holder anticlockwise and remove it from the reflector.
178 Vehicle care 2. Rotate bulb anticlockwise and remove from bulb holder. 3. Replace bulb. 4. Insert the bulb holder into the reflector and rotate clockwise. Tail lights 1. Release the cover and remove it. 2. Unscrew the two plastic securing nuts from the inside by hand.
Vehicle care 179 5. Unlatch the four retaining lugs and remove the bulb carrier. 6. Remove and replace the bulb. Tail light and brake light ( 1 ) Tail light ( 2 ) Turn signal light ( 3 ) Version with Light Emitting Diode (LED): Only brake light ( 1 ) and turn signal light ( 2 ) can be changed.
180 Vehicle care 2. Press the retaining lug and remove the bulb carrier downwards. 3. To replace the reverse light bulb ( 1 ), remove and replace the bulb. To replace the tail light/rear fog light bulb ( 2 ), push the bulb slightly into the socket, rotate anticlockwise, remove and replace the bulb.
Vehicle care 181 Side turn signal lights To replace bulb, remove lamp housing: 1. On left vehicle side, slide lamp to the front and remove it out of the front wing with the rear end. On right vehicle side, slide lamp to the rear and remove it out of the front wing with the front end.
182 Vehicle care 2. Remove lamp downwards, taking care not to pull on the cable. 3. Remove bulb holder from lamp housing by turning anticlockwise. 4. Pull bulb from bulb holder and replace it. 5. Insert bulb holder into lamp housing and turn clockwise.
Vehicle care 183 3. Rotate the bulb holder clockwise and remove. 4. Pull the bulb out of the bulb holder and replace it. 5. Insert the bulb holder into the housing and turn it anticlockwise. 6. Plug in the connector. 7. Attach the housing. Instrument panel illumination Have bulbs replaced by a workshop.
184 Vehicle care Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse. Engine compartment fuse box The fuse box is in the front left of the engine compartment. Disengage the cover, lift it upwards and remove. After having changed defective fuses close the fuse box cover and press until it engages.
Vehicle care 185 No. Circuit 1 Starter 2 – 3 Fuel filter, cooling 4 Horn 5 Terminal 30 6 Engine control module, trans‐ mission control unit 7 Fog light 8 Engine cooling 9 Engine cooling 10 Vacuum pump 11 Ignition, preheating 12 Headlamp levelling 13 Air conditioning system, terminal 15 14 Transmission control unit 15 High beam right No.
186 Vehicle care No. Circuit 22 Electrical parking brake 23 Tyre repair kit 24 Fuel pump 25 ABS 26 Heated rear window 27 ABS 28 Interior fan 29 Cigarette lighter 30 Air conditioning system 31 Front po.
Vehicle care 187 In right-hand drive vehicles, the fuse box is located behind a cover in the glovebox. Open the glovebox, pull cover upwards and remove.
188 Vehicle care Disengage the four retaining lugs and remove the cover. No. Circuit 1 Adaptive forward lighting 2 – 3 – 4 – 5 – 6 Rear power window, right 7 Adaptive forward lighting 8 Traile.
Vehicle care 189 Vehicle tools Tools Vehicles with spare wheel The jack and the vehicle tools are in the spare wheel well in the load compartment. Vehicles with tyre repair kit To open the compartment, disengage the cover and open it. The vehicle tools are in the right-hand compartment in the load compartment, together with the tyre repair kit.
190 Vehicle care Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage.
Vehicle care 191 Tyre pressures differ depending on various options. For the correct tyre pressure value, follow the procedure below: 1. Identify the engine identifier code. Engine data 3 216. 2. Identify the respective tyre. The tyre pressure tables show all possible tyre combinations 3 225.
192 Vehicle care If the system is ready again, a message is displayed in the Driver Information Centre with Uplevel-Display. Tread depth Check tread depth at regular intervals. Tyres should be replaced for safety reasons at a tread depth of 2-3 mm (4 mm for winter tyres).
Vehicle care 193 Tyre chains Tyre chains are only permitted on the front wheels. Always use fine mesh chains that add no more than 10 mm to the tyre tread and the inboard sides (including chain lock). 9 Warning Damage may lead to tyre blowout. Tyre chains are only permitted on tyres of size 195/65 R 15, 205/55 R 16 and 225/45 R 17.
194 Vehicle care 1. Take the sealant bottle and bracket with air hose from the insert. 2. Detach air hose from bracket and screw onto sealant bottle connection. 3. Position the sealant bottle on the bracket. Make sure that the bottle does not fall. 4.
Vehicle care 195 8. Press on/off switch on the compressor. The tyre is filled with sealant. 9. The compressor pressure gauge briefly indicates up to 6 bar whilst the sealant bottle is emptying (approx. 30 seconds). Then the pressure starts to drop. 10.
196 Vehicle care Note The driving characteristics of the repaired tyre is severely affected, therefore have this tyre replaced. If unusual noise is heard or the compressor becomes hot, turn compressor off for at least 30 minutes. The built-in safety valve opens at a pressure of 7 bar.
Vehicle care 197 Alloy wheels: Disengage wheel bolt caps with a screwdriver and remove. To protect the wheel, place a soft cloth between the screwdriver and the alloy wheel. 2. Variant 1: Install the wheel wrench ensuring that it locates securely and loosen each wheel bolt by half a turn.
198 Vehicle care Set the jack to the necessary height. Position it directly below the jacking point in a manner that prevents it from slipping. Attach jack handle and with the jack correctly aligned rotate handle until wheel is clear of the ground. Variant 2: Set the jack to the necessary height.
Vehicle care 199 Jacking position for lifting platform Rear arm position of the lifting platform at the underbody. Front arm position of the lifting platform at the underbody. Spare wheel Some vehicles are equipped with a tyre repair kit instead of a spare wheel.
200 Vehicle care Storing a replaced wheel in the load compartment using a strap Use the strap placed in the tool box. Vehicle tools 3 189. ■ Position the wheel on the load compartment floor close to one sidewall of the load compartment. ■ Place the loop end of the strap through the front lashing eye of the according side.
Vehicle care 201 9 Warning Storing a jack, a wheel or other equipment in the load compartment could cause injury if they are not fixed properly. During a sudden stop or a collision, loose equipment could strike someone. Store jack and tools always in the respective storage compartments and secure them by fixing.
202 Vehicle care ■ Never expose the vehicle battery to naked flames or sparks. ■ A discharged vehicle battery can already freeze at a temperature of 0 °C. Defrost the frozen battery before connecting jump leads. ■ Wear eye protection and protective clothing when handling a vehicle battery.
Vehicle care 203 4. Switch on electrical consumers (e.g. headlights, heated rear window) of the vehicle receiving the jump start. 5. Reverse above sequence exactly when removing leads. Towing Towing the vehicle Disengage cap at bottom and remove downwards.
204 Vehicle care Switch on ignition to release steering wheel lock and to permit operation of brake lights, horn and windscreen wiper. Transmission in neutral. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle.
Vehicle care 205 Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. After towing, unscrew the towing eye. Insert cap at the bottom and engage cap. Appearance care Exterior care Locks The locks are lubricated at the factory using a high quality lock cylinder grease.
206 Vehicle care Thoroughly rinse and leather-off the vehicle. Rinse leather frequently. Use separate leathers for painted and glass surfaces: remnants of wax on the windows will impair vision. Do not use hard objects to remove spots of tar. Use tar removal spray on painted surfaces.
Vehicle care 207 Liquid gas system 9 Danger Liquid gas is heavier than air and can collect in sink points. Take care when performing work at the underbody in a pit. For painting work and when using a drying booth at a temperature above 60 °C, the liquid gas tank must be removed.
208 Service and maintenance Service and maintenance General information ................... 208 Recommended fluids, lubricants and parts ..............
Service and maintenance 209 Make sure that the Service and Warranty Booklet is completed correctly as continuous proof of service is essential if any warranty or goodwill claims are to be met, and is also a benefit when selling the vehicle.
210 Service and maintenance Select the appropriate engine oil based on its quality and on the minimum ambient temperature 3 213. Additional engine oil additives The use of additional engine oil additives could cause damage and invalidate the warranty.
Technical data 211 Technical data Vehicle identification .................. 211 Vehicle data ............................... 213 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is stamped on the identification plate and on the floor pan, under the floor covering, visible under a cover.
212 Technical data Identification plate The identification plate is located on the rear right-hand door frame. Information on identification label: 1 = Manufacturer 2 = Type approval number 3 = Vehicl.
Technical data 213 Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries (except Belarus, Moldova, Russia, Serbia, Turkey) Only Is.
214 Technical data International service schedule Required engine oil quality All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Engine oil quality Petrol engines.
Technical data 215 All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Engine oil quality Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (i.
216 Technical data Engine data Sales designation 1.4 1.4 1.4 Engine identifier code B14XER B14NEL B14NET Number of cylinders 4 4 4 Piston displacement [cm 3 ] 1398 1364 1364 Engine power [kW] 74 88 10.
Technical data 217 Sales designation 1.6 1.6 1.6 1.6 Engine identifier code B16DTC B16DTL B16DTN B16DTH Number of cylinders 4 4 4 4 Piston displacement [cm 3 ] 1598 1598 1598 1598 Engine power [kW] 70.
218 Technical data Sales designation 1.3 1.3 1.7 Engine identifier code A13DTC A13DTE A17DTI Torque [Nm] 180 180 280 at rpm 1750-2500 1750-3500 2300 Fuel type Diesel Diesel Diesel Oil consumption [l/1000 km] 0.
Technical data 219 Performance Engine B14XER B14NEL B14NET Maximum speed 4) [km/h] Manual transmission 5) 5) 5) Automatic transmission – 185 5) 4) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle.
220 Technical data Engine A13DTC A13DTE A17DTI Maximum speed 4) [km/h] Manual transmission 160 168 – Automatic transmission – – 178 4) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle.
Technical data 221 Vehicle weight Kerb weight, basic model without any optional equipment Engine Manual transmission Automatic transmission without/with air conditioning [kg] B14XER 1361/1376 – B14N.
222 Technical data Kerb weight, basic model with all optional equipment Engine Manual transmission Automatic transmission without/with air conditioning [kg] B14XER –/1571 – B14NEL –/1613 –/166.
Technical data 223 Length of load compartment floor [mm] 815 Length of load compartment with folded rear seats [mm] 1642 Load compartment width [mm] 1038 Load compartment height [mm] 803 Height of load compartment opening 791 Wheelbase [mm] 2644 Turning circle diameter [m] 11.
224 Technical data Capacities Engine oil Engine B14XER B14NEL B14NET A13DTC A13DTE including Filter [l] 4.0 4.0 4.0 3.5 3.5 between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0 Engine B16DTC B16DTL B16DTN B16DTH A17DTI including Filter [l] 5.0 5.0 5.0 5.0 5.4 between MIN and MAX [l] 1.
Technical data 225 Tyre pressures Comfort with up to 3 people ECO with up to 3 people With full load Engine Tyres front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) B14XER 195/65 R15, 230/2.
226 Technical data Comfort with up to 3 people ECO with up to 3 people With full load Engine Tyres front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) A13DTC 195/65 R15, 230/2.
Technical data 227 Comfort with up to 3 people ECO with up to 3 people With full load Engine Tyres front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) A17DTI 195/65 R15 7) , 250/2.
228 Customer information Customer information Customer information ................ 228 Vehicle data recording and pri‐ vacy ........................................... 228 Customer information Declaration of conformity This vehicle has systems that transmit and/or receive radio waves subject to Directive 1999/5/EC.
Customer information 229 ■ Vehicle reactions in particular driving situations (e.g. inflation of an airbag, activation of the stability regulation system) ■ Environmental conditions (e.g. temperature) These data are exclusively technical and help identifying and correcting errors as well as optimizing vehicle functions.
230 Index A Accessories and vehicle modifications .......................... 165 Active head restraints ................... 36 Adaptive brake light .................... 144 Adaptive forward lighting .......... .................................. 99, 117, 175 Adjustable air vents .
231 Child restraint systems ................ 55 Cigarette lighter ........................... 89 Climate control ............................. 16 Climate control, service .............. 131 Climate control systems ............. 123 Clock..............
232 Fuel gauge ................................... 90 Fuel selector ................................ 91 Fuse box ..................................... 184 Fuses ......................................... 183 G Gauges ...................................
233 Oil ............................................... 167 Oil, engine .......................... 209, 213 Oil pressure .................................. 98 Outside temperature .................... 86 Overrun cut-off ........................... 135 P Parking .
234 Top-tether fastening eyes ............ 61 Tow bar....................................... 160 Towing ................................ 160, 203 Towing another vehicle ............. 204 Towing a trailer ........................... 160 Towing equipment .
www.opel.com Copyright by ADAM OPEL AG, Rüsselsheim, Germany. The information contained in this publication is effective as of the date indicated below.
Een belangrijk punt na aankoop van elk apparaat Opel Meriva (2014) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Opel Meriva (2014) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Opel Meriva (2014) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Opel Meriva (2014) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Opel Meriva (2014) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Opel Meriva (2014) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Opel Meriva (2014) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Opel Meriva (2014) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
