Gebruiksaanwijzing /service van het product OPR 2001 van de fabrikant Opticon
Ga naar pagina of 42
OPR 2001 Laser Barcode Scanner Specifications Manual.
Opticon OPR 2001 S pecifications Manual 2 All information subject to change without notice. Document History Model Number: OPR 2001 Specification Number: SS07011 Edition: 1 Original Spec Number: SS06121 Date: 2007-02-14 Copyright 2007 Opticon. All right s reserved.
Opticon OPR 2001 S pecifications Manual 3 Content s 1. Abstract .................................................................................................................................... 7 2. Overview ........................................
Opticon OPR 2001 S pecifications Manual 4 8.1.7. Handshaking .................................................................................................................... ...... 20 8.2. USB Interface Specifications .............................
Opticon OPR 2001 S pecifications Manual 5 15.1. Auto Trigger Settings ..................................................................................................... 38 15.1.1. Stand On ly ........................................................
Opticon OPR 2001 S pecifications Manual 6 Figure 24: Wedge cable......................................................................................................... .... 29 Figure 25: Serial number diagram ........................................
Opticon OPR 2001 S pecifications Manual 7 1. Abstract This manual provides specifications for the OPR 2001 laser barcode scanner. 2. Overview The OPR 2001 is a handheld laser barcode scanner. The use of a short-wavelength red laser beam enhances visibility when scanning lines.
Opticon OPR 2001 S pecifications Manual 8 3. Physical Features 3.1. Dimensions W 151.0 x D 56.0 x H 30.5 mm 3.2. Weight 60 grams max. (excluding cable weight) 4. Environmental Specifications 4.1. Operating Temper ature and Humidity Temperature: -5° to +50° C Humidity: 20 to 85% RH 4.
Opticon OPR 2001 S pecifications Manual 9 4.3. Ambient Light Immunity Decoding performance is guaranteed when the range of illumination on a barcode surface is between zero and the following values: I.
Opticon OPR 2001 S pecifications Manual 10 5. Electrical Specifications 5.1. RS-232C Parameter Symbol Min Typ Max Unit Notes Power supply voltage V DD 4.5 6.0 6.5 V Operating current I OP - 90 150 mA No buzzer Peak current I PEAK - 550 600 mA Standby current I PRE - 35 70 mA Startup time T D - 100 - ms 5.
Opticon OPR 2001 S pecifications Manual 11 6. Optical Specifications 6.1. Laser Scanning Specifications Parameter Specification Unit Light-emitting element Red laser diode - Emission wavelength 650 ±10 (25° C) nm Light output 1.
Opticon OPR 2001 S pecifications Manual 12 7. Technical Specifications The conditions for technical specifications are as follows, unle ss otherwise specified in each section.
Opticon OPR 2001 S pecifications Manual 13 7.2. Scan Area and Resolution The scan area is a circular area centered around the beam, which appears at various resolutions. Figure 3: Depth of field. Resolution Symbology PCS Quiet Zone Digits Depth of Field (mm) 1.
Opticon OPR 2001 S pecifications Manual 14 7.3. Pitch, Skew, and Tilt 7.3.1. Pitch Angle Scanning performance is guaranteed when α = ±35° Figure 4: Pitch.
Opticon OPR 2001 S pecifications Manual 15 7.3.2. Skew Angle and Dead Zone Scanning performance is guaranteed when skew angle: β ≤ ±50° (Excluding dead zone) Dead zone: β = ±8° (There are some.
Opticon OPR 2001 S pecifications Manual 16 7.3.3. Tilt Angle Scanning performance is guaranteed when γ ≤ ±20° Figure 6: Tilt angle Conditions Barcode Sample: OPTOELECTRONICS Test Sample Distance: 70 mm from the fr ont edge of the scanner Label: Pitch, Skew Angle, Dead Zone PCS = 0.
Opticon OPR 2001 S pecifications Manual 17 7.4. Curvature With 8-digit JAN/UPC/EAN barcodes, decoding performance is guaranteed when R = 15 mm. With 13-digit JAN/UPC/EAN barcodes, decoding performance is guaranteed when R = 20 mm. Figure 7: Curvature Conditions Barcode Sample: OPTOELECTRONICS Test Sample PCS = 0.
Opticon OPR 2001 S pecifications Manual 18 8. Interface Specifications 8.1. RS-232C Interface 8.1.1. Settings and Communication Reading menu barcodes [ZZ] + [U2] + [ZZ] can set the RS-232C interface default.
Opticon OPR 2001 S pecifications Manual 19 8.1.3. Pin Assignment Signal Pin Notes NC 1 Open (not connected) TXD 2 RXD 3 --- 4 Connecte d to pin 6 with jumper cable. GND 5 --- 6 Connecte d to pin 4 with jumper cable. CTS 7 RTS 8 NC 9 Open (not connected) FG SHELL Shield Connector: D-sub, 9-pin, Female Power supply: DC jack, EIAJ voltage Class 2 8.
Opticon OPR 2001 S pecifications Manual 20 8.1.5. Character Format Figure 9:Character format (same for both sendi ng a nd receiving) 8.1.6. Communication Format Figure 10: Communication format 8.1.7. Handshaking Select handshaking options using the menu or command listed below.
Opticon OPR 2001 S pecifications Manual 21 b) BUSY/READY The scanner and the host computer notify each other of their state and whether they can receive data with BUSY/READY through an RTS line. They can communicate state to each other through a CTS line when connected as in the following figure.
Opticon OPR 2001 S pecifications Manual 22 CTS, TXD signal timing When the CTS line (RTS signal of the host) is turned OFF while sending a TX D signal, the scanner transmits one character and waits. When the CTS signal is turned ON while transmitting a character, the character will be transmitted.
Opticon OPR 2001 S pecifications Manual 23 d) ACK/NAK After data has been transmitted, the scanner expects to receive one of the following responses from the host: • ACK response—Action: The scanner completes transmission with the good-read buzzer and returns to the initial state.
Opticon OPR 2001 S pecifications Manual 24 e) ACK/NAK NO RESPONSE When no response from the host is received within the setting time, the scanner assumes an ACK response, and returns to the initial state without the error buzzer. The other actions are the same as ACK/NAK.
Opticon OPR 2001 S pecifications Manual 25 8.2. USB Interface Specifications 8.2.1. Settings a) USB-HID Reading menu barcodes [ZZ] + [SU] + [ZZ] can set the USB-HID interface default. The OPR 2001 USB model uses a full-speed USB interface. b) USB-VCP Reading menu barcodes [ZZ] + [C01] + [ZZ] can set the USB-VCP interface default.
Opticon OPR 2001 S pecifications Manual 26 8.2.3. Interface Circuit Figure 19: Interface circuit Do not use the keyboard while the scanner is transmitting the data to the host. Doing so may cause failure in data transactions. 8.3. DOS/V Wedge In terface Specification 8.
Opticon OPR 2001 S pecifications Manual 27 8.3.2. Connectors a) DOS/V Host Connector 2 3 5 1 4 6 Figure 20: DOS/V host connector Contact Number Signal Name 1 CPU_DATA 2 NC 3 GND 4 VCC 5 CPU_CLK 6 NC b.
Opticon OPR 2001 S pecifications Manual 28 9. Cable and Connector 9.1. RS-232C Cable (Standard specification) Type: Straight Diameter: Φ 4.8±0.5 mm Length: 1500 +50, -0 mm Cores: 6 insulated wires, 1 conductive wire Weight: Approximately 40 g Figure 22: RS-232C cable 9.
Opticon OPR 2001 S pecifications Manual 29 9.3. Wedge Cable (Standard specification) Type: Y cable Diameter: Φ 4.8 ±0.5 mm Length: 1500 +50, -0 mm Cores: 6 insulated wires, 1 conductive wire Weight: Approximately 50 g Figure 24: Wedge cable 9.
Opticon OPR 2001 S pecifications Manual 30 10. Default Settings 10.1. Barcodes Scan the following menu barcodes to return to the default settings. RS-232C Default Functions Menu labels Menu codes SET .
Opticon OPR 2001 S pecifications Manual 31 Wedge Default (without external keyboard) Functions Menu labels Menu codes SET _ZZ_ ZZ AT wedge default _UB_ UB With keyboard _KL_ KL END _ZZ_ ZZ 10.
Opticon OPR 2001 S pecifications Manual 32 Symbology Read Transmit Code Length Transmit CD Calculate CD Set Prefix Set Suffix Others Industrial2of5 X X — CR Interleaved2of5 X X — C.
Opticon OPR 2001 S pecifications Manual 33 10.3. Default Settings 2: Read Options, Trigger, Buzzer Item Default Setting Setting the number of characters Fixed length OFF all codes Read mode Single rea.
Opticon OPR 2001 S pecifications Manual 34 11. Serial Number The serial number as shown below is affixed to the scanner. Figure 25: Serial number diag ram 12. Packaging Specifications 12.1. Individual Packaging Specification Put the scanner in a protective foam bag and place it in a sin gle packing box.
Opticon OPR 2001 S pecifications Manual 35 13. Durability 13.1. Electrical Noise No malfunction occurred when sinusoidal electrical noise (10H z -100kHz, < 0.1Vpp) was added to a power supply line. Conditions Barcode Sample: OPTOELECTRONICS Test Sample PCS: 0.
Opticon OPR 2001 S pecifications Manual 36 13.3. Vibration Strength No malfunction occurred after the following vibration test. Vibration Test: Increase the frequency of the vibration from 10 Hz to 100 Hz with accelerated velocity 19.6m/s 2 (2G) for 60 minutes in non-operating state.
Opticon OPR 2001 S pecifications Manual 37 14. Reliability MTBF (Mean Time Between Failures) of this product is 10,000 hours. The estimate of MTBF is based on standard operation of the product within the recommended temperature range and without extreme electronic or mechanical shock.
Opticon OPR 2001 S pecifications Manual 38 Auto trigger can be enabled in 2 ways: • Stand detection mode: This option enables auto trigger automatically in case the scanner is inserted into the stand. • Normal auto trigger mode. *Descriptions in ( ) show menu IDs.
Opticon OPR 2001 S pecifications Manual 39 15.1.2. Always Enable auto trigger all the time. Functions Menu labels Menu codes SET _ZZ_ ZZ Enable auto trigger _+I_ +I Disable auto trigger stand detection _*5_ *5 END _ZZ_ ZZ 15.1.3. Manually Only trigger manually (default).
Opticon OPR 2001 S pecifications Manual 40 16. Regulatory Compliance 16.1. Laser Safety JIS C 6802:2005 Class 2 IEC60825-1+A2:2001 Class 2 CDRH Class II 16.
Opticon OPR 2001 S pecifications Manual 41 17. Safety Handle this product carefully. Do not deliberately subject it to any of the following. 17.1. Shock • Do not throw or drop the scanner. • Do not place heavy objects on the cables. 17.2. Temperature Conditions • Do not use the scanner at temperatures outside the specified range.
Opticon OPR 2001 S pecifications Manual 42 18. Mechanical Drawing Dimensions: 151.0 mm x 56.0 mm x 30.5 mm (except protruding parts) Figure 30: Mechanical draw in g.
Een belangrijk punt na aankoop van elk apparaat Opticon OPR 2001 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Opticon OPR 2001 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Opticon OPR 2001 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Opticon OPR 2001 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Opticon OPR 2001 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Opticon OPR 2001 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Opticon OPR 2001 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Opticon OPR 2001 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
