Gebruiksaanwijzing /service van het product NN-SD698S van de fabrikant Panasonic
Ga naar pagina of 40
© 2008 Panas onic Home Appliances Microwave Oven (Shanghai) Co., Ltd. All rights reserved. Unauthorize d copying and distrib ution is a violation of law.
2 NN-SD698S / NN-ST6 78S / NN-ST658W.
3 NN-SD698S / NN-ST6 78S / NN-ST658W.
1 SCHEMATIC DIAGRAM 5 2 DESCRIPTIO N OF OPERATING SEQU ENCE 6 2.1. Variable power cooking control 6 2.2. Inverter power supply circuit 6 2.3. Inverter defros t 6 2.4. Sensor cooking 6 2.5. Sensor reheat 7 2.6. Steam sensor and digital progra mmer circuit 7 2.
1 SCHEMATIC DIAGR AM 5 NN-SD698S / NN-ST6 78S / NN-ST658W.
2.1. Variable power cooking control High Voltage Inverter Power Supply (U) controls output power by the signal from Digital Programmer Circuit (DPC). Power relay always stay on, but PWM (Pulse Width Modulation) signal controls microwave output power.
Explanation of the Auto Sensor Cooking process 1. During the first 10 second period there is no microwave activity. When calculating the T2 time by using the formula below make sure this 10 seconds is subtracted from the T1 time. In other words, T1 time starts at the end of the 10 second period.
Unlike many other appliances, the microwave oven is a high voltage, high current device. It is free from danger in ordinary use, though extreme care should be taken during repair. CAUTION Servicemen should remove their watches and rings whenever working close to or replacing the magnetron.
Discharging the high voltage capacitors WARNING There is high voltage present with high current capabilities in the circuits of the primary and secondary windings, choke coil and heat sinkof the inverter. It is extremely dangerous to work on or near these circuits with the oven energized.
4.1. Magnetron 1. Discharge high voltage charge. 2. Remove 1 screw holding air guide A on the oven cavity. 3. Remove 1 screw holding air guide A on the magnetron. 4. Remove 1 screw holding air guide B. 5. Remove 1 screw holding themistor. 6. Disconnect 2 high voltage lead wires from magnetron filament terminals.
4.3. Low voltage transformer and/or power relays (RY1, RY2) CAUTION: Be sure to ground any static electric charge built up in your body before handling the DPC.
4.6. Turntable motor 1. Remove the motor cover by breaking off at the 8 spots indicated by arrows with a cutter or the like. NOTE: After removing the motor cover, be sure that cut portions are properly trimmed or bent to the inside so that no sharp edges will be exposed to outside.
4.8. Inverter power supply CAUTIONS 1. Always leave the ground ing plate in place. 2. Always securely tighten the ground screw through the bottom of the chassis (base) . 3. Secure ly connect 3 lead wire conne ctors. 4. Make sure the heat sink has enough space (gap) from the oven.
WARNING 1. High voltage is presen t at the output termin als of the High Voltag e Inverter (U) includi ng aluminum heat sink during any cook cycle. 2. It is neither neces sary nor advisable to attemp t measuremen t of the high voltage.
5.5. Inverter power supply (U) DO NOT try to REPAIR H.V. Inverter power supply (U). Replace complete H.V. Inverter(U) Unit. WARNING: HIGH VOLTAGE Test if failure codes H95, H97 or H98 appear when performing the following procedure. It is recommende d to use an AC line input current ammeter for testing.
6.1. Adjustment of primary latch switch, secondary latch switch and monitor interlock switch. 1. Mount the Primary latch switch, the Secondary latch switch and the Monitor interlock switch to the door hook assembly as shown in illustration.
7.1. Equipment • Electromagnat ic radiation monitor • Glass thermometer 212°F or 100°C • 600cc glass beaker 7.2. Procedure for measuring radiation leakage Note before measuring: • Do not exceed meter full scale deflection. Leakage monitor should initially be set to the highest scale.
7.4. At least once a year, have the radiation monitor checked for calibration by its manufacturer. 18 NN-SD698S / NN-ST6 78S / NN-ST658W.
8 TROUBLESHOOTING GUIDE DANGER: HIGH VOLTAGES 1. DO NOT RE-ADJUST PRESET CONTROL on the H.V.In verter (U). It is very dange rous to repair or adjust without proper test equipment because this circuit genera tes very large current and high voltage. Operating a misaligned inverte r circuit is dange rous.
8.2. (Troubleshoo ting) Other problems SYMPTOM CAUSE CORRECTIONS 1. Oven is dead. 1. Open or loose lead wire harnes s Fuse is OK. 2. Open therma l cutout / thermistor Check therma l cutout is defect ive. No display and no operat ion at all. 3. Open low voltage transfo rmer 4.
8.3. Troubleshoot ing of inverter circuit (U) and magnetron This oven is programmed with a self diagnostics failure code system which will help for troubleshooting. H95, H97, H98 and H99 are the provided failure codes to indicate magnetron and inverter circuit problem areas.
8.4. SIMPLE WAY OF H.V. INVERTER/MAGNETRON TROUBLESH OOTING Purpose: Simple way (3/37 seconds rule) of identifying whether it’s Magnetron, Inverter or others. Set-up: The unit under question is connected through the Ammeter as shown below. Procedure: Follow the matrix table below to identify the problem source.
8.6. How to check the semiconducto rs using an OHM meter 23 NN-SD698S / NN-ST6 78S / NN-ST658W.
9 EXPLO DED VIEW AND PARTS LIST 9.1. EXPLODED VIEW 24 NN-SD698S / NN-ST6 78S / NN-ST658W.
9.2. PARTS LIST NOTE: 1. When ordering replacement part(s), please use part number(s) shown in this part list. Do not use description of the part. 2. Important safety notice: Components identified by mark have special characteristic s important for safety.
Ref. No. Part No. Part Name & Description Pcs/Set Remarks 45 F65856K50AP INVERTER BRACKET 1 46 F03347D00RP MENU LABEL 1 SD698S 46 F03347G50RP MENU LABEL 1 ST678S,ST658W 48 F40264T60APG AIR GUIDE B.
9.3. WIRING MATERIALS Ref. No. Part No. Part Name & Description Pcs/Set Remarks W1 F030A7D00RP LEAD WIRE HARNESS 1 W2 F030E5L00AP H.V.LEAD WIRE 1 W3 F03537D00AP LEAD WIRE HARNESS U 1 (INCLUDING TH.
9.4. DOOR ASSEMBLY Ref. No. Part No. Part Name & Description Pcs/Set Remarks D1 F30186P40AG DOOR KEY A 1 SD698S,ST678S D1 F30184Y30XN DOOR KEY A 1 ST658W D2 F301A8X00SCP DOOR A (U) 1 SD698S D2 F30.
9.5. ESCUTCHEO N BASE ASSEMBLY 9.5.1. NN-SD698S Ref. No. Part No. Part Name & Description Pcs/Set Remarks E1 F603L8X00RP D.P.CIRCUIT (AU) 1 SD698S E2 F603Y8X00RP D.
9.5.2. NN-ST678S Ref. No. Part No. Part Name & Description Pcs/Set Remarks E21 F603L8V60RP D.P.CIRCUIT (AU) 1 ST678S E23 F800L8V60SRP ESCUTCHEON BASE (U) 1 ST678S E26 F80725Y00SAP DOOR OPENING BUT.
9.5.3. NN-ST658W Ref. No. Part No. Part Name & Description Pcs/Set Remarks E41 F603L7G50RP D.P.CIRCUIT (AU) 1 ST658W E43 F80346K50HAP ESCUTCHEON BASE 1 ST658W E49 F630Y8V70HRP MEMBRANE SWITCH (U) .
9.6. PACKING AND ACCESSORIES Ref. No. Part No. Part Name & Description Pcs/Set Remarks P1 F00038X00RP INSTRUCTION MANUAL 1 SD698S P1 F00038V60RP INSTRUCTION MANUAL 1 ST678S,ST658W P2 F01028X00SRP .
10 DIGITAL PROGRAMM ER CIRCUIT 10.1. NN-SD698S 33 NN-SD698S / NN-ST6 78S / NN-ST658W.
34 NN-SD698S / NN-ST6 78S / NN-ST658W.
10.2. NN-ST678S 35 NN-SD698S / NN-ST6 78S / NN-ST658W.
36 NN-SD698S / NN-ST6 78S / NN-ST658W.
10.3. NN-ST658W 37 NN-SD698S / NN-ST6 78S / NN-ST658W.
38 NN-SD698S / NN-ST6 78S / NN-ST658W.
10.4. PARTS LIST 10.4.1. NN-SD698S Ref. No. Part No. Part Name & Description Pcs/Set Remarks BZ310 L0DDEA000014 BUZZER 1 2.0KHz C10 AECETK1V471B AL CHEM CAPACITOR 1 470µF/35V C13,C16 AECETS1C220B AL CHEM CAPACITOR 2 22µF/16V C482 AECETS1H010B AL CHEM CAPACITOR 1 1µF/50V C483 AECETS1HR47B AL CHEM CAPACITOR 1 0.
10.4.3. NN-ST658W Ref. No. Part No. Part Name & Description Pcs/Set Remarks BZ310 L0DDEA000014 BUZZER 1 2.0KHz C12 AECETK1V471B AL CHEM CAPACITOR 1 470µF/35V C13 AECETS1C220B AL CHEM CAPACITOR 2 22µF/16V CX320 H2B800400007 CERAMIC RESONATOR 1 8.
Een belangrijk punt na aankoop van elk apparaat Panasonic NN-SD698S (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Panasonic NN-SD698S heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Panasonic NN-SD698S vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Panasonic NN-SD698S leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Panasonic NN-SD698S krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Panasonic NN-SD698S bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Panasonic NN-SD698S kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Panasonic NN-SD698S . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
