Gebruiksaanwijzing /service van het product VL-G201 van de fabrikant Panasonic
Ga naar pagina of 40
Thank you for pu rchasing a Pa nasonic V ideo Interc om System. Please read this Installation and Operation Guide before using the unit and save for future reference.
2 Table of Contents Important Information Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Additional safety information . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Important Information Import ant safety instructions 1) Read these instructions. All the safety and operating instructions should be read before the a ppliance i s operated. 2) Keep these instructions. The safety and op erating instructions should b e retained for future refere nce.
4 Important Information 12) Use only with th e cart, stand, tripod, bracke t, or ta ble specified by th e manufactur er , or sold with the apparatus. When a cart is us ed, use cauti on when moving the cart / apparatus combination to avoid injury from tip-over .
5 Important Information For business u sers in the Europe an Union If you wish to discard electrical and electroni c equip ment, please contact your dealer or supplier for furt her informati on. Information on D isposal in other Cou ntries outside the European Union This symbol is only valid in the European Uni on.
6 Important Information For your safety This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 3 amp fuse is fitted in this plug. Should the fuse need to be replaced please ensur e that the replacement fuse has a rating of 3 amps and that it is approved by AST A or BSI to BS1362.
7 Important Information How to replace the fuse: Open the fuse compartment with a screwdriver and rep lace the fuse (and fuse cover). For best performance L If a power failure occurs, the unit will not function. L Do not place any objects within 20 cm of the monitor station.
8 Introduction and Installation Included items 1234 5678 9j k l No. Item Quantity Notes 1 Monitor station 1 ------ 2 Mounting bracket 1 Attached to rear of the monitor statio n. 3 Wood screw 2 For the monitor station. (4 mm x 16 mm) 4 Power cable 1 ------ 5 Door station 1 ------ 6 Mounting bracket 1 Attached to rear of the door station.
9 Introduction and Installation Comp atible Panasonic PBXs This unit can be used with Panasonic PBXs (page 27). Please consult your dealer for compatible PBX information.
10 Introduction and Installation Location of controls Monitor st ation Front view Side view Rear view MONITOR BRIGHT DOOR T ALK VOLUME RINGER VOLUME RINGER ANSWER AUTO PUSH HOLD HIGH LOW OFF A N SW E R AUTO PUSH HOLD HIGH LOW OFF B I D E F J G A H C OFF PBX MODE ON K G201CE(E).
11 Introduction and Installation A Microphone B Display C MONITOR button L Allows you to monitor the sound and came ra image from the door station (p age 34). D BRIGHT button L Allows you to adjust the di splay brightness. 5 levels are available. E DOOR button L Allows you to open the door (page 35).
12 Introduction and Installation Door st ation Front view Rear view A Camera L When a visitor presses the Call Button, the camera will turn on and an image of the visitor will be shown on the monitor display . B Microphone C Call Button L The Call Button is lighted with a blue LED light whil e the power is on.
13 Introduction and Installation Before inst allation T o a void malfunction or communication di sturbances, do not install eithe r the door station or the monitor station in the following locations: – Places where vibration or any other kind of impact occurs.
14 Introduction and Installation Note: L The measurements and angles are for reference purposes and may vary depending on the environment. L If a strong light i s shining on the door station, the vi sitor ’s face may not be distinguishable. Do not place the door station in the fo llowing locations.
15 Introduction and Installation Wiring schematic diagram Note: L The Door Opener wiring schematic diagram is an example. Refer to the wirin g instructions provided with your Door Opener and PBX for details. L Refer to the technical data on page 38 when connecting to a Door Opener .
16 Introduction and Installation Inst alling the door st ation Make sure to install the door station on a flat, vertical wall. Import ant: L On the bottom surface of the do or station, there is a hole to allo w water to drai n. Do not cover it up w hen inst alling.
17 Introduction and Installation 2 Attach the mounting bracket to the wall using th e wood screws (3.8 mm x 20 mm). L Before drilling, see page 13 for installation location. 3 Connect the wires that connect to the moni tor station to the terminal conne ctor by unscrewing the screws, pushing in the wir es, then tightly fa stening the screws.
18 Introduction and Installation L If you want to connect the wires without them passing through a hole in the wall, conne ct the wires by passing them through the ribs and the wire hole. 4 Mount the door station to the mounting bracket. Push the door station down until it is secure.
19 Introduction and Installation 5 Insert the hex-head screw using the longer end of the allen key. 6 Attach the bolt cover using the shorter end of the allen key. L Use protrusion on the sh orter end of the allen ke y to rotate the bolt cover until it is secure.
20 Introduction and Installation Inst alling the monitor st ation Note: L When connecting to a PBX, make sure the { PBX MODE } switch is set to { ON } before installing the monitor station (page 28). 1 Install the mounting bracket to a wall using the wood screws (4 mm x 16 mm).
21 Introduction and Installation 3 Attach the wires that connect to the door station to the terminal. See page 26 for detai ls on how to attach the wires.
22 Introduction and Installation 4 Mount the monitor station to the mounting bracket. Push the monitor station down until it is secure. 5 Take out the AC adaptor and the DC terminal from the ca se. L Push the arrow mark on the front case, then release from the rear case.
23 Introduction and Installation 6 Connect the power cable to the DC terminal, the power cord to the AC adapto r, then connect the pow er cord to the AC outlet (100 V – 240 V, 50 Hz / 60 Hz). L Be sure to connect the power cable to the 2 holes on the left side of the DC terminal.
24 Introduction and Installation T o attach the AC adaptor and the DC terminal to a wall By placing the AC adaptor and the DC terminal in the case and mou nting the case to th e wall, you can protect the AC adaptor and the DC termin al from tampering and exposure.
25 Introduction and Installation 3 Attach the front of the case. Note: L T o op en the case again, push the bottom o f the front case, then release from the rear case.
26 Introduction and Installation T o attach the power cable L While pressing on the button with a pointed objec t such as a screwdriver , insert the pow er cable into the terminal. L T o discon nect the power cable, pres s on the button while pulling out.
27 Introduction and Installation Using with another machine Note: L See page 15 for wiring information. When connected to a PBX Connecting to a PBX allows you to answer door calls using addi tional machines.
28 Using the Unit Tu r n i n g { PBX MODE } switch ON/OFF When connecting to a PBX (page 30), turn { PBX MODE } switch on. If not, turn { PBX MODE } switch off. The default setting is { OFF } . 1 Remove the switch cover from th e rear of the monitor station.
29 Using the Unit 3 Attach the switch cover to the rear of the monitor station. Switch cover G201CE(E).book Page 29 Friday, Nov ember 11, 2005 4:46 PM.
30 Using the Unit Connecting to a PBX Connecting to a PBX allows you to answer door calls fr om an y telephone. See page 15 for wiring information. Please use only a Panasonic PBX. See page 9 for the PBX model list that is compatible and other optional h ardware.
31 Using the Unit Answering a door call There are 3 ways to answer a door call. Choose the desired mode by changing the { ANSWER } switch position. Import ant: L When speaking with a caller , speak in turns. If you and the ca ller speak at the same time, you will not hear each other .
32 Using the Unit { PUSH } mode (Push to t alk mode) 1 When a ringer tone is heard, press { TA L K } . 2 Speak to the visitor. 3 To end the conversation, press { TA L K } . L The display will turn off. { AUTO } mode (Auto t alk mode) This mode allows you to answer the call by vo ice.
33 Using the Unit Note: L Speak clearly about 50 cm away from the microphone. L While the display is on, you can press { BRIGHT } repeatedly to select the desired brightness. If a power failure occurs, the brightness setting will be reset. L If you do not answer a door ca ll within 30 seconds, the display wil l turn off.
34 Using the Unit Monitoring the out side Y ou can mo nitor the sound and camera image from the door station for up to 1 minute at a time. 1 Press { MONITOR } . L The outside image will be shown o n the display , and the ou tside sound will be heard. The inside sound will not be heard at the door station.
35 Using the Unit Opening a door (Door Opener) Y ou ca n open the door using the monitor stati on (a separate Door Opener is required). 1 While the display is on, press and hold { DOOR } . L The door will remain open whi le { DOOR } is pressed. { DOOR } G201CE(E).
36 Help T roubleshooting Problem Cause and so lution The display is not clear or is blurry. L The surface of the door stat ion is dirty . Clean it with a soft dry cloth. L The surface of the door station is wet with dew . Wait for the condensation to evaporate.
37 Help Cleaning Clean the unit with a soft, dry cloth when cleaning. For excessive dirt, wipe the unit with a slightly damp cloth. Import ant: L Do not use anything containing alcohol, polis h powder , powder soap, benzine, thinner , wax, petroleum, or boiling water .
38 General Information T echnical dat a about this product Monitor st ation Power supply: 24 V DC Current consump tion: S t andby: Approx. 37 mA At operation: Approx. 420 mA Dimensions: Approx. height 136 mm x width 136 mm x depth 32 mm Mass (Weight): Approx.
39 General Information Note: L Design and specifications are su bject to change without no tice. L The pictures and illustrations in these instru ctions may vary slightly from the actual product.
PFQX2319ZA DC1005SM1 1 15 1/2 For your future reference Attach your sales receipt here. Panasonic Commun ications Co., L td . 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan Copyright: L This material is copyrigh ted by Panasonic Communicatio ns Co.
Een belangrijk punt na aankoop van elk apparaat Panasonic VL-G201 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Panasonic VL-G201 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Panasonic VL-G201 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Panasonic VL-G201 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Panasonic VL-G201 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Panasonic VL-G201 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Panasonic VL-G201 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Panasonic VL-G201 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
