Gebruiksaanwijzing /service van het product WJ-GXD900 van de fabrikant Panasonic
Ga naar pagina of 119
Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. MPEG2 Encoder Model No.
2 The serial number of this product may be found on the bottom of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. Model No.
3 IMPOR T ANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings.
CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...........................................................................3 CONTENTS....................................................................................................................... .4 FEATURES .
5 HOW TO USE THE CGI COMMANDS ............................................................................85 CAMERA CONTROL .................................................................................................86 CAMERA SETTINGS MENUS CONTROL .
6 FEA TURES The MPEG2 Image Delivery System delivers image data as streaming data to a network such as a LAN. This system consists of the encoder that converts an analog video signal (NTSC) to the digital data (MPEG2), and the decoder that converts the digital data (MPEG2) to the analog video signal (NTSC).
7 PRECAUTIONS ● Refer all work related to the installation of these products to qualified service per- sonnel or system installers. ● Do not operate the appliances beyond their specified temperature, humidity , or power source ratings. Use the appliance at temperatures within –10 °C - + 50 °C (14 °F - 122 °F) and humidity below 90 %.
8 PRECAUTIONS SYSTEM REQUIREMENTS Setting up and operating the encoder and the decoder with a web browser, and execution of the "Panasonic IP Setup" software are possible with PCs meeting the system requirements described below.
9 TRADEMARKS AND REGISTERED TRADEMARKS • Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation in the U.S. and/or other countries. • Intel and Pentium are trademarks of Intel Corporation. • Ethernet is a registered trademark of Xerox Corporation.
10 MAJOR OPERA TING CONTROLS AND THEIR FUNCTIONS q Power Indicator (OPERATE) This indicator lights up when the power of the encoder is on. When the temperature inside the encoder becomes remarkably high, this indicator will start blinking. It will take around 2 minutes and 45 seconds to start up the encoder after turning the power on.
11 DIP1: Normally, select OFF. When ON is selected, the firmware, as the start up program (loaded at the factory), starts up. The value of the settings will not be deleted. DIP2: When ON is selected, the IP address and all the current settings will return to the default settings.
12 q Ethernet Port (100BASE -TX) (RJ-45) Connect an Ethernet cable to connect to a network. Use a category 5 cable (100BASE-TX). LINK1 Indicator: This indicator lights up when the encoder is linked to a network through this port. SPEED Indicator: This indicator lights up when connection (100BASE-TX) is established.
13 MPEG2 Decoder Front Panel q Power Indicator (OPERATE) This indicator lights up when the power of the decoder is on. When the temperature inside the decoder becomes remarkably high, this indicator will start blinking. It will take around 2 minutes to start up the decoder after turning the power on.
14 will light up when decoding streaming data to video signals. The indicators will blink when the decoder is not receiving streaming data. The indicators will go off when decoding has stopped. STATUS 5 (RUN): This indicator lights up when the decoder is operable.
15 q Ethernet Port (100BASE-TX/1000BASE-T) (RJ-45) Connect with a network device such as router or hub using an Ethernet cable. Depending on the transmission speed between a device and the decoder, use the proper cable as suggested below. When the transmission speed is 1000BASE-T Enhanced category 5 (STP (Shielded Twisted Pair)) cable.
16 Multicast T ransmission The multicast transmission will be suitable for the following systems. • When the number of cameras is more than the number of monitors in a system, and switching streamin.
17 When monitoring pictures of a camera with two or more monitors Use the CGI command to designate pictures of the camera to be displayed on the monitors. Send the CGI command to each decoder and set the receiving IP address of the camera whose pictures are to be displayed on the monitors.
18 System Example (Switching streaming video) This is a system example with 8 cameras and 4 monitors, and switching streaming video using a PC. Refer to the "SWITCHING STREAMING VIDEO" section of "HOW TO USE THE CGI COMMANDS" on page 90 about the CGI command to switch streaming video.
19 Operation Example (Switching streaming video) These are examples to operate the systems introduced on the previous pages. • Switching currently monitored streaming video to another streaming video Use the following CGI commands.
20 System example (Recording streaming video) This is a system example to control the digital disk recorder (WJ-HD500) from a PC. OPERATE S TATUS MPEG2 Encoder WJ-GXE 900 1 2 3 4 5 6 7 8 OPERATE S TAT.
21 Setting Example (Recording streaming video) The digital disk recorder can be controlled by using the PS•Data (through the RS-485 data port). Perform the settings for the RS-485 data port on the RS-485 DATA PORT page as shown below. The settings on the VIDEO page and the NETWORK page are also required according to the user's environment.
22 Unicast T ransmission The unicast transmission will be suitable for the following system. • When it is necessary to monitor pictures from a specific camera on a specific monitor System Example When using the unicast transmission, the number of cameras and monitors should be same.
23 Receiving and Sending Serial Data (RS-485) The encoder receives and sends serial data (duplex) as shown in the illustration below. Required Settings for RS-485 Perform the following settings to receive and send serial data.
24 Alarm Function and a Reset Switch System Example Refer to the following system example when connecting a sensor or a security control door with a reset switch.
25 ALM / 0F000xxx XX XX / 00 YYYY MM DD hh mm ss +/- xxxx xxxx xx (Fixed) (Fixed) 8 digits Alarm type Number (Fixed) Fixed Alarm Occurred Time (GMT) Time Zone Alarm Code Contact Number (Year/Month/Date/Hour/Minute/Second) ALARM IN • Alarms The encoder can receive the following alarms.
26 • Alarm Reset There are 2 ways to reset alarm (reset by the CGI command and setting the reset timer on the menu). To reset the contact alarm, there are 3 ways (reset by the CGI command, setting the reset timer on the menu and manual reset (alarm off timing)).
27 INST ALLA TIONS Warning The installation should be made by qualified service personnel or system installers. Places to avoid • Places exposed to sunlight directly or near a source of heat such as.
28 Rack Mounting The encoder and the decoder can be installed in the following racks. • Racks equivalent to EIA standard: Type 19" EIA standard (depth: more than 450 mm (17-11/16")) Important • Do not install the encoder and the decoder above an appliance which generates heat such a power amplifier.
29 Mounting the encoder 1. Remove the four rubber feet by removing the four screws from the bottom of the encoder. 2. Place the rack mounting brackets (sold separately, see below for details) on both sides of the encoder and tighten with the four screws supplied to the rack mounting brackets.
30 Installing in a container box (Only for the Encoder) The encoder can be installed in a container box. When required to install the encoder in a container box, install as below. How to install 1. Place the supplied simple mounting brackets with the supplied fixing screws on the bottom of the encoder.
31 Description Labels The description labels and the code labels are provided as standard accessories of the encoder and the decoder respectively. Attach each label on the top of the appliances as described below according to needs.
32 How to Display the Settings Menus The settings for the encoder and the decoder are required to operate for the first time respectively. (The settings will be required also when the settings are initialized.) The settings for the encoder and the decoder can be performed using a web browser installed on a PC.
33 Setup with the Provided " Panasonic IP Setup " Software Set up the network of the encoder/decoder by using the "Panasonic IP Setup" software included on the provided CD- ROM. Note: If a firewall (including software) exists, allow access to all UDP ports.
34 The setup window appears. SETUP 4. Set parameters for each item. "IP Address" "Subnet Mask" "Default Gateway" "DNS Server address" 5. Click the [SET] button after completing the settings. Important It takes around 20 seconds to complete the settings of the encoder/decoder after the [SET] button is pressed.
35 Begin the setup when the PC is in the same condition as it is just after startup. The "Control Panel" window appears. 1. Select "Control Panel" ([Start] - [Settings] - [Control Panel]). 2. Click once to select the [Network] icon.
36 SETUP The "Network" window appears. Note: If the "TCP/IP" item is not displayed, refer to the operating instructions of the OS and follow the procedures to install the TCP/IP. The "TCP/IP Properties" window appears. 3.
37 Using Windows 2000 The following procedures are examples when using Windows 2000. You can proceed in the same way when using Windows NT. Important: Log in as one of the administrators before beginning the setup. Begin the setup when the PC is in the same condition as it is just after the startup.
38 SETUP The "Local Area Connection Properties" window appears. Note: If the "Internet Protocol (TCP/IP)" item is not displayed, refer to the operating instructions of the OS and follow the procedures to install the TCP/IP. The "Internet Protocol (TCP/IP) Properties" window appears.
39 Using Windows XP (Category V iew) Begin the setup when the PC is in the same condition as it is just after the startup. The "Control Panel" window appears. The "Network and Internet Connections" window appears. 1. Select "Control Panel" ([Start] - [Control Panel]).
40 SETUP The "Network Connections" window appears. The "Local Area Connection Properties" window appears. The "Internet Protocol (TCP/IP) Properties" window appears. 4. Click to select "Local Area Connection", and then click "Change settings of this connection" in the "Network Tasks" menu.
41 To perform the settings of the encoder, display the top page of the encoder first. Refer to the network administrator about the required network addresses (IP addresses, etc.). 1. Enter the IP address of the encoder in the address box of the web browser and press the Enter key.
42 ■ CONTROL/ST A TE page (page 43) Destination IP address and destination port number of each of the VIDEO IN connectors streaming video and audio data to be sent Starting and stopping to encode video and audio data ■ VIDEO page (for each video input channel) (page 44) Camera No.
43 CONTROL/ST A TE page ■ Item Descriptions CH Number of the VIDEO IN 1 - 4 connectors DESTINATION IP ADDRESS/DESTINATION PORT No. Displaying the respective destination IP addresses and destination .
44 VIDEO page Perform the settings for the VIDEO IN connectors respectively. The numbers of "CH" are the number of the VIDEO IN connectors respectively. Note: Click the [SET] button to save the changed settings. Otherwise, the changed settings will not be saved.
45 SOURCE PORT No. Enter a port number for the video and audio data source. 1024 to 65535 are available for the "SOURCE PORT No.". The default setting is 51000 for all channels. BIT RATE Enter a desired bit rate for streaming video and audio data.
46 AUDIO page Note: Click the [SET] button to save the changed settings. Otherwise, the changed settings will not be saved. ■ Item Descriptions To send audio from the audio source connected to the encoder, select "ON". To not to send audio from the audio source connected to the encoder, select "OFF".
47 ALARM page Perform the settings for each alarm type and the alarm notification. Note: Click the [SET] button to save the changed settings. Otherwise, the changed settings will not be saved. ■ Item Descriptions ALARM SETUP Perform the settings for each alarm type in detail.
48 ALARM-DR Y CONT ACT page Note: Click the [SET] button to save the changed settings. Otherwise, the changed settings will not be saved. ■ Item Descriptions No. The numbers of the ALARM IN connectors MAKE CONTACT Set whether to control the encoder by making contact or not.
49 RESET/TIMER (SEC) 1 - 60, 90, 120, 150, 180, 240, 300 - 3 600: 60 SEC INTERVAL When the alarm is reset, the bit rate returns to the set value on the VIDEO page and the alarm status is released. Select the method of release from the following. CGI RESET Resets the alarm using the CGI commands.
50 ALARM-CAMERA SITE page Note: Click the [SET] button to save the changed settings. Otherwise, the changed settings will not be saved. ■ Item Descriptions No. The numbers of the VIDEO IN connectors ON/OFF Set whether to control the encoder by alarm input or not.
51 CGI RESET Resets the alarm using the CGI commands. Refer to "RESETTING THE ALARM/DISPLAYING THE ALARM STATUS" of the "HOW TO USE THE CGI COMMANDS" section on page 102. TIMER The timer starts when the alarm is detected. When the entered time for this setting has passed, the alarm will be reset automatically.
52 ALARM-VIDEO LOSS page Note: Click the [SET] button to save the changed settings. Otherwise, the changed settings will not be saved. ■ Item Descriptions No. The numbers of the VIDEO IN connectors ON/OFF Set whether to control the encoder by alarm input or not.
53 RESET/TIMER (SEC) 1 - 60, 90, 120, 150, 180, 240, 300 - 3 600: 60 SEC INTERVAL When the alarm is reset, the bit rate returns to the set value on the VIDEO page and the alarm status is released. Select the method of release from the following. CGI RESET Resets the alarm using the CGI commands.
54 RS-485 DA T A PORT page Perform the settings to send and receive serial data duplex. The setting values should be the same for both devices. Notes • Packets will be sent to a network when either setting of "WAITING DATA SIZE TO SEND PACKET" or "WAITING TIMER TO SEND PACKET" is fulfilled.
55 NETWORK PORT SETUP DESTINATION SETUP Perform the settings for the destination which receives the packets. Select "DESTINATION IP ADDRESS IN RECEIVING PACKET" or "REFERENCE SETUP (FOLLOWINGS)". DESTINATION IP ADDRESS IN RECEIVING PACKET Serial data will be sent to the IP address contained in the received packet.
56 NETWORK page Note: It is necessary to restart the encoder to save the changed settings. Otherwise, the changed settings will not be saved. Restarting the encoder can be done on the MAINTENANCE page. Click the [MAINTENANCE] button in the left column to go to the MAINTENANCE page and click the [RESTART] button on the MAINTENANCE page.
57 SYSTEM page Notes • The Main CPU mode is the advanced function for integrated control. There is no product on the market as of June 2003. • Click the [SET] button to save the changed settings.
58 SETTINGS MENUS OF THE ENCODER When "ON" is selected, it is also necessary to set the following 4 items: • NTP SERVER HOST/IP ADDRESS • INTERVAL (1 - 24 hour) • TIME ZONE • DAYLIGHT SAVINGS NTP SERVER HOST/IP ADDRESS Enter a host name or an IP address of an NTP server.
59 USER page Perform the settings to restrict users to access the encoder on this page. It is possible to restrict access to the encoder by the "USER AUTHENTICATION" and the "HOST AUTHENTICATION". Refer to the next page when using both the "USER AUTHENTICATION" and the "HOST AUTHENTICATION".
60 SETTINGS MENUS OF THE ENCODER HOST page Perform the settings on this page when restricting devices from accessing the encoder by using IP addresses. It is possible to restrict access to the encoder by the "USER AUTHENTICATION" and the "HOST AUTHENTICATION".
61 ■ Item Descriptions CAMERA CONTROL Click this link text to display the CAMERA CONTROL page. On the CAMERA CONTROL page, it is possible to control the camera and to display the camera settings menus. FIRMWARE UPDATE Update the firmware of the encoder by executing the update files sent to the encoder in advance.
62 SETTINGS MENUS OF THE ENCODER HOW TO UPDA TE THE FIRMW ARE It is possible to update to the firmware of the encoder. 1. Acquire the file for update and copy it into the desired directory on the PC. 2. Transfer the file from the PC to the encoder. Follow the procedure below to transfer using the MS- DOS command.
63 CAMERA CONTROL page It is possible to control the camera or to display the camera picture on the monitor on this page. It is also possible to display the settings menus of the camera and perform the settings. Notes • Depending on the connected camera, some functions may not be available.
64 SETTINGS MENUS OF THE ENCODER FOCUS Adjust the focus of the camera by clicking the [NEAR], [FAR] or [AUTO] buttons. NEAR: Focusing on near objects FAR: Focusing on far objects AUTO: Focusing on objects in the center on the displayed area Note: It is impossible to keep focusing by holding down the [NEAR] or [FAR] buttons.
65 CAMERA MENU CONTROL page Perform the camera control on this page. Note: The camera settings menu will be displayed on the monitor connected to the decoder. To connect the monitor to the encoder directly, connect the monitor to the VIDEO OUT connector respective to the camera to be set.
66 To receive the motion pictures sent from the encoder, do the following. Refer to a network administrator about the required network addresses (IP addresses, etc.). 1. Enter the IP address of the decoder in the address box of the web browser and press the Enter key.
67 ■ CONTROL/ST A TE page (page 68) Confirming the status of the decoder and the receiving IP address and the receiving port number Starting and stopping to decode video and audio data ■ VIDEO pag.
68 SETTINGS MENUS OF THE DECODER CONTROL/ST A TE page Note: It is impossible to switch streaming video when using the unicast transmission. ■ Item Descriptions CH Numbers of the VIDEO OUT 1 - 4 connectors of the decoder RECEIVING STREAM IP ADDRESS/RECEIVING STREAM PORT No.
69 VIDEO page Perform the settings of the VIDEO OUT connectors respectively. It is necessary to apply the same parameters (values) set on the VIDEO page of the encoder as the settings of the encoder for the settings on this menu. Notes • Click the [SET] button to save the changed settings.
70 SETTINGS MENUS OF THE DECODER LATENCY BUFFER Perform the setting for the latency buffer (size of which the internal memory of the decoder can absorb the transmission delay of the packets in the network). When the bigger size is selected for the latency buffer, the transmission delay becomes longer.
71 DISPLA Y page Notes • Perform the setting for the camera numbers and the camera titles on the VIDEO page of the encoder. • Click the [SET] button to save the changed settings. Otherwise, the changed settings will not be saved. ■ Item Descriptions CAMERA No.
72 SETTINGS MENUS OF THE DECODER CHARACTER BACKGROUND COLOR Select how to display the background of the characters displayed on the monitor from the following. NONE: The characters displayed on the monitor will be displayed without background color. GRAY: The characters displayed on the monitor will be displayed in a gray color background.
73 NETWORK page Note: It is necessary to restart the decoder to save the changed settings. Otherwise, the changed settings will not be saved. Restarting the decoder can be done on the MAINTENANCE page. Click the [MAINTENANCE] button in the left column to go to the MAINTENANCE page and click the [RESTART] button on the MAINTENANCE page.
74 SETTINGS MENUS OF THE DECODER SYSTEM page Notes • The Main CPU mode is the advanced function for integrated control. There is no product on the market as of June 2003. • Click the [SET] button to save the changed settings. Otherwise, the changed settings will not be saved.
75 match the current time by referring to an NTP server through a network. Select "ON" or "OFF" to set whether to use the NTP or not.
76 SETTINGS MENUS OF THE DECODER USER page Perform the setting to restrict users to access the decoder on this page. It is possible to restrict access to the decoder by the "USER RESTRICTION" and the "HOST AUTHENTICATION".
77 HOST page Perform the setting to restrict hosts (IP addresses) to access the decoder on this page. It is possible to restrict access to the decoder by the "USER RESTRICTION" and the "HOST AUTHENTICATION". Notes: • Click the [SET] button to save the changed settings.
78 SETTINGS MENUS OF THE DECODER [ADD] button Click to add a host after entering the host information. ● DELETE Select a host to be deleted from the pull-down menu, and click the [DELETE] button. Confirm that the host has been deleted from the pull- down menu.
79 MAINTENANCE page It is possible to update the firmware of the decoder or restart the decoder. ■ Item Descriptions FIRMWARE UPDATE Update the firmware of the decoder by executing the update files sent to the decoder in advance. Refer to the following for more information about the firmware update.
80 • The power cord, connectors or the power plug are damaged. If you continue to use it, a fire or an electric shock may occur. Unplug the power plug immediately, and refer servicing of the plug to qualified service personnel. TROUBLESHOOTING Before asking for repairs, please check the following symptoms.
81 Symptom Possible cause / Possible solution Reference page • Is the correct cable (straight or cross) being used? Use the straight cable when connecting the unit to a switching hub or router.
• Is a temporary network trouble (a broken wire, connection trouble, etc.) occurring? When temporary software trouble occurs, it will be recovered automatically. Depending on the status of the trouble, communi- cation might be disconnected. In this case, try to connect again.
83 Symptom Possible cause / Possible solution Reference page • Are "RECEIVING IP ADDRESS" and "RECEIVING PORT No." of the decoder set correctly to receive streaming video and audio data? Check "DESTINATION IP ADDRESS" and "DESTINATION PORT No.
84 Symptom Possible cause / Possible solution Reference page • Is a temporary network trouble (a broken wire, connection trouble, etc.) occurring? When temporary software trouble occurs, it will be recovered automatically. Depending on the status of the trouble, communication might be disconnected.
85 The HTTP (Hyper Text Transfer Protocol) is used to control the encoder and decoder. The following can be controlled: • Camera control • Camera settings menus control • Switching streaming vid.
86 CAMERA CONTROL When a Panasonic combination camera (WV-CW860, WV-CS850, etc.) or a pan-tilt head is connected to the VIDEO IN connector of the encoder, it is possible to control the camera using the CGI commands.
87 Item Parameter name Parameter value Description Iris control IRIS –10 - –1 CLOSE 0 RESET 1 - 10 OPEN It will take around 60 ms for one step increment or decrement of the IRIS param- eter to adjust the iris.
88 CAMERA SETTINGS MENUS CONTROL When a Panasonic camera is connected to the VIDEO IN connector of the encoder, it is possible to control the camera settings menus using the CGI commands. ■ Format ■ Response ■ Important Notice It is necessary to enter the parameter value for the "CHSEL" parameter.
89 ■ Examples 1. To display the menu of the camera connected to the VIDEO IN 1 connector http://192.168.0.10/cgi-bin/camctrl.cgi?CHSEL=1&MENU=on 2. To move the cursor on the menu of the camera connected to the VIDEO IN 2 connector downward http://192.
90 SWITCHING STREAMING VIDEO When using the multicast transmission, it is possible to switch the streaming video displayed on the monitor using the following CGI commands.
91 ■ Example 1. To output the image from the VIDEO IN 3 connector (destination IP address: 239.192.0.3; port number: 50000) of the encoder by the VIDEO OUT 1 connector (multicast transmission) http://192.168.0.11/control4?decode=start&ch=01&address=239.
92 CONTROLLING ST ART /ST OP OF THE ENCODER Start and stop the transmission of streaming video and audio data from the encoder. ■ Format ● Start encoding (Streaming transmission) ● Stop encoding.
93 ■ Examples 1. To start streaming transmission from the VIDEO IN 1 connector (start encoding) http://192.168.0.10/control4?encode=start&ch=01 2.
94 CONTROLLING ST ART / ST OP OF THE DECODER Start and stop the reception of the streaming video and audio data by the decoder. When receiving streaming video and audio data after starting decoding, images will be displayed on the monitor and audio will be output.
95 ● Stop decoding Item Parameter name Parameter value Description Stop decoding decode end Identifier to stop decoding VIDEO OUT connector number ch 01 - 04 Select a VIDEO OUT connector number (01 - 04) which stops decoding. ■ Examples 1. To start displaying images from the VIDEO OUT 1 connector (start decoding) http://192.
96 DISPLA YING THE ST A TUS OF THE ENCODER Displays the status of the encoder. ■ Format ■ Response xxx.xxx.xxx.xxx: Video stream IP address (xxx ： 0 - 255) yyyyy: DESTINATION PORT No. (1024 - 65535) PLAY: Encoder is active STOP: Enoder is not active HTTP /1.
97 ■ Example 1. To display the status of the encoder http://192.168.0.10/control4?status=get Response PLAY1:239.192.0.1:50000 PLAY2:239.192.0.2:50000 PLAY3:239.
98 DISPLA YING THE ST A TUS OF THE DECODER Displays the status of the decoder. ■ Format ■ Response HTTP /1.1 XXXXXXXXXXXXX CR LF Cache-Control: no-cache CR LF Content-Type: text/plain CR LF Content-Length: XX CR LF (Store the octet number of the Message-Body decimally) CR LF PLAY1:xxx.
99 xxx.xxx.xxx.xxx: Video stream receiving IP address (xxx ： 0 - 255) yyyyy: Port number (yyyyy: 1024 - 65535) PLAY: Decoder is active, and is receiving video streaming and displaying it on the monitor.
100 CONTROLLING THE BIT RA TE OF STREAMING VIDEO AND AUDIO DA T A It is possible to change the bit rate of the encoder. Since the settings of the encoder are not overwritten, the changed rate will return by turning on/off the encoder.
101.
102 RESETTING THE ALARM / DISPLA YING THE ALARM ST A TUS Displays the status of the alarm or resets the alarm against the encoder. The bit rate of the streaming video and audio data returns to the set value by resetting the alarm that sets the status of the alarm to OFF.
103 ■ Response ● Response of alarm reset ● Response of displaying alarm status ■ Examples 1. To reset the alarm occurred at the contact input port 1 http://192.168.0.10/control4?alm=reset&ch=01 2. To reset the video loss alarm occurred at the VIDEO IN 3 http://192.
104 DISPLA YING THE CONT ACT INPUT ST A TUS Displays the status of each contact input port. ■ Format ■ Response HTTP /1.1 200 OK CR LF Cache-Control: no-cache CR LF Content-Type: text/plain CR LF .
105 DISPLA YING THE ST A TUS OF VIDEO LOSS Displays the receiving status of the video sync signals from camera or the VTR connected to the VIDEO IN connector of the encoder. When the power of the camera connected with the video cable is off, the status will be OFF.
106 MUTING THE AUDIO It is possible to mute audio temporarily, or resume muted audio. ■ Format ■ Response ■ Important Notice • "audio=out&ch=(parameter value)&mute=(parameter valu.
107 MUL TISCREEN DISPLA Y Designates image to be displayed on the monitor connected to the QUAD connector by the CGI commands. It is possible to select whether to display in multiscreen (quad) or to display one of the 4 image sources.
108 CONTROLLING THE CONT ACT OUTPUT It is possible to designate the output port, output type (open/close), and output time of the control pulse which is supplied from the contact output port of the encoder. ■ Format ■ Response ■ Important Notice • The output time will be invalid when "momentary" is selected for the output mode.
109 ■ Examples 1. Close output for 1 second for the port 1 http://192.168.0.10/cgi-bin/pioctrl.cgi?com=set_pio&PIO=1&OUT=latch&TYPE=close &TIME=10&submit=ACTION 2. Open output for 15 seconds for the port 2 http://192.168.0.10/cgi-bin/pioctrl.
110 REST ARTING THE ENCODER / DECODER It is possible to restart the encoder/decoder using the CGI commands. ■ Format ● Restarting the encoder ● Restarting the decoder ■ Response ■ Important Notice The user name and the password authentication will be required when trying to restart the encoder/decoder.
111 UPDA TING Update the firmware of the encoder/decoder by executing the update file transferred to the encoder/decoder in advance. Refer to the page 62 or page 79 to transfer the file to the encoder or the decoder respectively.
112 ENCODER Setting Page Item Default setting NETWORK IP ADDRESS 192.168.0.10 SUBNET MASK 255.255.255.0 DEFAULT GATEWAY 192.168.0.1 DNS SERVER 0.0.0.0 SPEED/DUPLEX AUTO SYSTEM MODE WEB MODE VIDEO&.
113 Setting Page Item Default setting AUDIO SETUP OFF OFF OFF OFF ALARM-DRY CONTACT No.1 No. 2 No.3 No.4 MAKE-CONTACT CLOSE CLOSE CLOSE CLOSE CAMERA PRESET No.
114 Setting Page Item Default setting HOST HOST AUTHENTICATION OFF HOST IP ADDRESS - SUBNET MASK - ACCESS LEVEL - DELETE - MAINTENANCE ACCEPT EXCLUSIVE COMMAND IP ADDRESS - The bit rate when the encoder detects an alarm (both the dry contact and camera site alarm) No.
115 DECODER Setting Page Item Default setting NETWORK IP ADDRESS 192.168.0.11 SUBNET MASK 255.255.255.0 DEFAULT GATEWAY 192.168.0.1 DNS SERVER 0.0.0.0 SPEED/DUPLEX AUTO SYSTEM MODE WEB MODE VIDEO&.
SPECIFICA TIONS ● ENCODER Basic Specification Power Source 120 V AC 60 Hz Power Consumption 23 W Ambient Operating Temperature –10 °C - +50 °C (14 °F - 122 °F) Ambient Operating Humidity Less than 90% (non-condensing) Weight Approx. 2.9 kg (6.
● DECODER Basic Specification Power Source 120 V AC 60 Hz Power Consumption 45 W Ambient Operating Temperature –10 °C - +50 °C (14 °F - 122 °F) Ambient Operating Humidity Less than 90 % (no-condensing) Weight Approx.
118.
PANASONIC CANADA INC. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 PANASONIC SALES COMPANY DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
Een belangrijk punt na aankoop van elk apparaat Panasonic WJ-GXD900 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Panasonic WJ-GXD900 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Panasonic WJ-GXD900 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Panasonic WJ-GXD900 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Panasonic WJ-GXD900 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Panasonic WJ-GXD900 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Panasonic WJ-GXD900 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Panasonic WJ-GXD900 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
