Gebruiksaanwijzing /service van het product 5216 van de fabrikant Paradyne
Ga naar pagina of 20
TM 1 Hotwire 5216 Remote T ermination Unit (RTU) Customer Premises Installation Instructions Document Number 5216-A2-GN10-10 February 1998 Before Y ou Begin An optional POTS (Plain Old T elephone Service) splitter is available for the 5216 RTU.
2 Package Checklist V erify that your package contains the following: - Model 5216 Remote T ermination Unit (RTU) - DSL interface cable with RJ1 1 modular plugs - Power cord with power transformer - T wo ferrite chokes - W arranty card Refer to Cables & Connectors , page 13, for standard pin numbers.
3 When a POTS splitter is used at both ends of the local loop, wiring is connected: H From the demarcation point to the CP POTS splitter , and H From the demarcation point to the DSL jack.
4 DSL Access without a POTS Splitter When the 5216 RTU is installed without a POTS splitter , a second telephone wiring pair is needed for DSL access. 97-15609 Punchdown Block or NID DSL Jack RT U Cus.
5 Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connected from the customer premises side of the punchdown block or the NID to the DSL jack. T ypically , the punchdown block is installed in commercial locations and the NID is installed in residential locations.
6 Green (T1) and red (R1) are the standard wiring colors used in the next two illustrations. In the following example, a NID is used without a POTS splitter .
7 2. Locate the DSL pair of T1/R1 connectors on the customer premises side of the NID or punchdown block. Attach the wiring that will be connected to the DSL jack.
8 DSL Jack Installation The 5216 RTU connects to the local loop via wiring from the demarcation point to an RJ1 1 wall jack. The DSL twisted-pair wiring from the local loop terminates at a new or existing wall jack. It may be necessary to install a standard single RJ1 1 jack or replace a single jack with a double RJ1 1 jack.
9 Installing the R TU Place the 5216 RTU on a flat surface with clearance for the rear connectors. " Procedur e 1. Use the RJ1 1 6-pin cable for the DSL connection. Insert one end of the cable into the jack labeled DSL. Insert the other end into the wall jack labeled DSL.
496-14952 97-15303c Ethernet Line PO WER ETHERNET DSL Hotwire RTU F err ite Choke 10 3. Place the large ferrite choke on the Ethernet cable as closely as possible to the RTU. Pass the Ethernet cable through the ferrite choke twice, creating a loop as shown.
11 6. Close the two halves around the cable and snap the ferrite choke shut. Press down on the plastic latch to secure the ferrite choke in place around the cable. 7. Plug the transformer into an AC outlet. The RTU hardware installation is now complete.
12 LED Status Condition DSL Blinking ON OFF RTU is establishing the DSL link. The LED blinks on and off about five times per second. The DSL link is now active and ready to transmit and receive data. The DSL link has not been established. ETHERNET ON OFF The Ethernet 10BaseT connection to the end-user system is active.
97-15304 6- P i n RJ 1 1 Pl ug DS L Li ne Pi n #1 Pi n #6 13 LED Symptom Action DSL and Ethernet LEDs are on and there is no data transmission. The DSL link and the Ethernet link have been established. If the problem continues, contact the NSP . Ethernet LED is off.
14 H The Ethernet interface crossover cable connector uses an 8-pin, non-keyed modular plug. 97-15305 8- P i n Pl u g E t he r ne t Ca bl e Pi n #1 Pi n #8 10BaseT TX D + 10BaseT TX D 10BaseT R X .
15 Model 5216 R TU T echnical Specifications Item Specification * Height x Width x Depth 1.35 ″ x 6.00 ″ x 8.75 ″ (3.43 cm x 15.35 cm x 22.23 cm) Weight 1 lb. 1 oz. (0.48 kg) Power Class 2 T ransformer normal service input voltage range Input: 100 V ac, 50 Hz; 120 V ac, 60 Hz; or 230 V ac, 50/60 Hz Output: 15 Vdc nominal (+ 10%), minimum 0.
16 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered.
17 CE Marking When the product is marked with the CE mark on the equipment label, this demonstrates full compliance with the following European Directives: H Directive 73/23/EEC – Council Directive .
18 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal Communications Commission’s Rules. This compliance information statement pertains to the following products: T rade Name: Hotwire Model Number: 5216-A2-200 This device complies with Part 15 of the FCC Rules.
19 EMI W arnings ! W ARNING: T o Users of Digital Apparatus in Canada: This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial brouilleur du Canada.
20 W arranty , Sales, and Service Information Contact your local sales representative, service representative, or distributor directly for any help needed.
Een belangrijk punt na aankoop van elk apparaat Paradyne 5216 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Paradyne 5216 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Paradyne 5216 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Paradyne 5216 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Paradyne 5216 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Paradyne 5216 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Paradyne 5216 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Paradyne 5216 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
