Gebruiksaanwijzing /service van het product 1082, 144, I van de fabrikant Patton electronic
Ga naar pagina of 28
USER MANUAL MODEL 1082/I and 1082/144/I iDSL Modem with 10Base- T Interface SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P art# 07M1082I-UM Doc# 03318U2-001 Rev .
2 T ABLE OF CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 FCC Information ........................................................................... 4 1.2 CE Notice .........................
3 A.8 Connectors ................................................................................. 25 A.9 Power .......................................................................................... 25 A.10 Temperature Range ......................
4 1.0 W ARRANTY INFORMATION P atton Electronics warrants all Model 1082/I and Model 1082/144/I components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of shipment.
5 1.3 SERVICE All warranty and non-w arranty repairs must be returned freight prepaid and insured to P atton Electronics. All retur ns must ha ve a Return Mater i- als A uthorization number on the outside of the shipping container .
6 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or One Y ear par ts and labor .
7 2.2 DESCRIPTION The Model 1082/I and Model 1082/144/I are Multi Rate iDSL Modems that provide seamless MA C La yer connectivity between 2 peered 10Base-T LANs. Now , Enter prise users no longer need to hassle with a bridge and a CSU/DSU or recurring leased line costs.
8 3.0 PPP OPERATIONAL BACKGR OUND PPP is a protocol used f or multi-ple xed transport over a point-to-point link. PPP operates on all full duple x media, and is a symmetr ic peer-to- peer protocol, wh.
9 Figure 2. Cisco router with serial interface, configured as PPP Half-Bridge Figure 2 shows a typical Cisco router with a serial interf ace configured as a PPP Half Bridge. The router serial interface uses a remote de vice that suppor ts PPP bridging to function as a node on the remote Ether net network.
10 Figure 3. T ransparent bridging between two routers ov er a ser ial interface Figure 3 illustrates transparent bridging between two routers o ver a serial interface (s0). Br idging will occur between the two Ethernet inter- f aces on router A (e0 and e1) and the two Ethernet interfaces on router B (e0 and e1).
11 4.0 CONFIGURATION The Model 1082/I and Model 1082/144/I each are equipped with 16 DIP s witches that enable configur ation of the unit f or a wide v ariety of appli- cations. This section describes switch locations and e xplains the different configurations.
12 Figure 5. DIP switches S2 and S2 Figure 5 shows the orientation of the DIP s witches in the “ON” and “OFF” positions. Configuring DIP Switch S1 DIP s witch S1 is where you configure the data r ate, asynchronous or synchronous data f ormat, transmit clock source, and response to RDL request.
13 Note When setting the 1082 for SNMP Management, the DTE r ate switches (S1-1,S1-2, and S2-1) m ust be also set to the ON posi- tion. Theref ore, to set a 1082 unit SNMP Mangagement mode, the follo wing s witches hav e to be at the ON position, S1-1, S1-2, S2-1.
14 Switches S1-6 and S1-7: System Clock Mode Use Switches S1-6 and S1-7 to configure the 1082/I or Model 1082/144/ I f or internal, or receive recov er clock mode.
15 Configuring DIP switch “S2” Use the eight DIP s witches in S2 to enable 19.2 kbps or 144* kbps syn- chronous operation and set the loopbac k modes. The f ollowing tab le summarizes def ault positions of DIP s witches S2-1 through S2-8. Detailed descriptions of each switch f ollow the table .
16 Switch S2-2: Front P anel Switch Disable Use s witch S2-2 to enable or disab le the front panel toggle switches. Switches S2-3, S2-6, S2-7 and S2-8: Reser ved S2-2 Setting On Disable the front pane.
17 5.0 INSTALLATION When the Model 1082 has been properly configured, it may be con- nected to the DSL twisted pair interf ace, the 10Base-T Ethernet Inter- f ace, and the po wer source. This section descr ibes these connections. Figure 6. Model 1082/I or Model 1082/144/I rear view 5.
18 The RJ-45 connector on the Model 1082’ s twisted pair interface is polar- ity insensitive and is wired f or a two-wire interf ace. The signal/pin rela- tionships are shown in Figure 7 belo w . Figure 7. Model 1082/I twisted pair line interface 5.
19 5.4 POWER CONNECTION Universal A C P ower (100–240V AC) The Model 1082/I uses a 5VDC , 2A universal input 100–240V AC , power supply (center pin is +5V). The universal input po wer supply has a male IEC-320 power entry connector . This power supply connects to the Model 1082/I by means of a barrel jac k on the rear panel.
20 DC P ower The 36-60 VDC DC to DC adapter is supplied with the DC version of the Model 1082. The blac k and red leads plug into a DC source (nominal 48VDC) and the barrel power connector plugs into the barrel po wer sup- ply jack on the rear panel of the 1082.
21 6.0 OPERATION When the Model 1082/I and Model 1082/144/I hav e been properly config- ured and installed, it should operate transparently . This sections describes power-up , LED status monitors, and the b uilt-in loopbac k test modes . 6.1 POWER-UP Bef ore applying power to the Model 1082/I or Model 1082/144/I, please read section 5.
22 T able 1: LED status monitor indications LED Description DSL Link (Activ e Green) Solid green (On) indicates that the end to end DSL F ramer Link is up, signifying that the link across the DSL span is active . The DSL Link LED is Off when the link is down.
23 6.3 T EST MODES The Model 1082/I and Model 1082/144/I has a built-in proprietary loop- back test mode , plus a b uilt-in V .52 BER test patter n generator , for e valu- ating the condition of the modems and the communication link. These tests can be activated ph ysically from the front panel, or via the interf ace .
24 Activating RDL can be done in tw o ways: 1. Mov e the front panel toggle switch to appropriate position. 2. Set remote loopback from SNMP screen (when used with 1092ARC Rack Card) Note Remote loopback cannot be activ ated until approximately 45 seconds after the two modems hav e linked to each other .
25 APPENDIX A 1082/I Specifications A.1 T RANSMISSION FORMAT Synchronous or asynchronous A.2 T RANSMISSION LINE Single unconditioned twisted pair A.3 CLOCKING Internal or receive loopback A.4 DISTANCE A.5 DATA RATES Synchronous 19.2, 32, 56, 64, and 128 kbps, (and 144 kbps on 1082/144 only); Asynchronous 0–38.
26 A.10 T EMPERATURE RANGE 32–122°F (0–50°C) A.11 ALTITUDE 0–15,000 f eet (0–4,572 meters) A.12 HUMIDITY 5–95% non-condensing A.13 DIMENSIONS 4.
27 APPENDIX B MODEL 1082/I F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES Model # Description 1082/I 10Base-T , DSL Modem 1082/144/I 10Base-T DSL modem with maximum data rate of 144 kbps 48V -PSM DC P ower Supply Module 08055DCUI 100-240V AC (+5V ±5% reg.
28 Notes _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________.
Een belangrijk punt na aankoop van elk apparaat Patton electronic 1082, 144, I (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Patton electronic 1082, 144, I heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Patton electronic 1082, 144, I vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Patton electronic 1082, 144, I leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Patton electronic 1082, 144, I krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Patton electronic 1082, 144, I bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Patton electronic 1082, 144, I kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Patton electronic 1082, 144, I . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
