Gebruiksaanwijzing /service van het product 1092 van de fabrikant Patton electronic
Ga naar pagina of 19
USER MANUAL MODEL 1092 High Speed, 2-Wire, Sync & Async Short Range Modem SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .
T ABLE OF CONTENTS Section Page 1.0 W arranty Information .............................................................2 1.1 Radio and TV Interference 1.2. CE Notice 1.3 Service Information 2.0 General Information .....................................
2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor .
3.0 CONFIGURA TION The Model 1092 is equipped with two sets of eight DIP switches, which allow configuration of the unit to a wide variety of applications. The Model 1092 is also equipped with an internal switch that allows selection of 1 15 or 230 V AC power inputs (Note: this switch is not present in Models 1092-UI and 1092-DC).
Switches S1-4 and S1-5: Asynchronous/Sync Operation Use Switches S1-4 and S1-5 to configure the Model 1092 for async/sync operation. Both switches must be set in the “Off” position.
3.2 CONFIGURING THE SOFTW ARE SWITCHES The Model 1092 features a menu-driven command system that allows you to configure either the local or remote 1092.
3.2.1 Configuring the Local 1092 T o configure the LOCAL 1092, make a selection from the following MAIN MENU screen. T o configure the REMOTE 1092, type [$] (Shift- 4) and refer to Section 3.2.2 . MAIN MENU Option 1: Display Active Configuration Select Option 1 to display the most recent configuration of the local Model 1092 (See below).
1. DTE Rate Select Option 1 in the SOFTW ARE CONFIGURA TION menu to select the async. or sync. DTE Rate of the Model 1092. Different DTE Rate menu screens will display for async.
MAIN MENU Option 5: Select Hardware/Software Control Select Option 5 from the MAIN MENU selects whether the Model 1092 will use the hardware switch settings or the software switch settings for its active configuration. If Options 1 or 2 are selected, the 1092RC will use the current hardware or software switch settings as the active configuration.
MAIN MENU Option 7: T est Modes Select Option 7 from the MAIN MENU to select the test mode status of the Model 1092. (below). The Model 1092 T est Mode settings help to verify the integrity of the data link and isolate communication difficulties. NOTE: An error counter is displayed when the unit is in one of the above test modes except LLB and RDL.
3.2.2 Configuring the Remote 1092 T o configure the Remote 1092, make a selection from the following REMOTE UNIT CONFIGURA TION MAIN MENU. T o return to the LOCAL 1092 MAIN MENU screen, press [ESC] and refer to Section 3.
4.2 CONNECTION TO THE SERIAL PORT The serial port interface on the Model 1092 uses interchangeable QuikConnect™ Modules. Each QuikConnect™ Module has a 50-pin card edge connector on one side and a serial port interface on the other . Figure 4 below shows how a QuikConnect™ Module plugs into the back of the Model 1092.
Installing the New QuikConnect™ Module 1) Make sure the power switch is off. Leave the power cord plugged into a grounded outlet to keep the unit grounded. 2) Hold the module with the faceplate toward you and align the module with the guide slots in the rear panel of the Model 1092.
4.3.2 Connecting to a DC Power Source The 48 VDC power supply option uses a 3-pin terminal block with spring-type connectors. Please refer to the Model 1090 Series Service Manual for further instructions. 25 5.0 OPERA TION Once the Model 1092 is properly configured and installed, it should operate transparently .
NS Glow red to indicate that the local Model 1092 has not yet connected with the remote 5.3 TEST MODES The Model 1092 offers two proprietary loopback test modes, plus a built-in V .52 BER test pattern generator , to evaluate the condition of the modems and the communication link.
2. If the above test indicates no errors are present, move the V .52 toggle switch DOWN, activating the “51 1/E” test with errors present. If the test is working properly , the local modem's red “ER” LED will glow .
APPENDIX B P A TTON MODEL 1092 F ACTOR Y REPLACEMENT P ARTS AND ACCESSORIES Patton Model # Description IM1/A ...............................V .24 with DB25F IM1/B ...............................RS422/RS530 with DB25F IM1/C ............................
APPENDIX C P A TTON MODEL 1092 INTERF ACE PIN ASSIGNMENT (Continued) V .35 Interface (M/34F Female Connector) (DCE Configuration) Pin # Signal B ...........................SGND (Signal Ground) C ...........................R TS (Request to Send) D ....
APPENDIX D P A TTON MODEL 1092 Pin Out Control Port The 1092 control port is an 8 position connector , compliant with EIA/TIA-561. Pin Function RJ45 Pin No. Ground 4 Receive data (to DTE) 5 T ransmit data (from DTE) 6 35 Dear V alued Customer , Thank you for purchasing Patton Electronics products! W e do appreciate your business.
Een belangrijk punt na aankoop van elk apparaat Patton electronic 1092 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Patton electronic 1092 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Patton electronic 1092 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Patton electronic 1092 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Patton electronic 1092 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Patton electronic 1092 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Patton electronic 1092 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Patton electronic 1092 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
