Gebruiksaanwijzing /service van het product PCX-V12 van de fabrikant Peavey
Ga naar pagina of 24
P C X - V 1 2 P C X - V 1 2 T rue diversity VHF wireless receiver T rue diversity VHF wireless receiver OPERATING GUIDE.
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suf ficient magnitude to constitute a risk of electric shock to persons.
INTRODUCTION Thank you for selecting a Peavey Pro Comm PCX- V12 quartz controlled single channel true diversity wireless microphone system. Before operating and installing this system please read this instruction manual carefully and thoroughly in order to attain the correct operating procedures and to achieve the best results.
1. Antenna Input Connector A 2. Power Switch and Indicator: When the switch is turned on the red indicator illuminates to denote normal power status. 3. RF Signal Level Indicator: Indicates the RF signal strength received from the microphone. As soon as the signal is emitted from the microphone the LED indicator illuminates.
7. DC 12V Input Jack: Connect the 12V DC plug from the AC/DC adapter . 8. Balanced Audio Output Jack: XLR type connector 9. Unbalanced Audio Output Jack: 1/4" Phone Jack 10. Unbalanced Level Switch: “LOW selection is for “Microphone-Level” output.
3. Audio Output Connection: a. Unbalanced Level Switch Setting Position: Make sure to match the unbalanced output setting to the device input setting. The incorrect setting could result in low sensitivity level or over load distortion.
3. TWO 19/2-INCH UNITS RECEIVER INST ALLA TION A. Setup for single half-rack receiver 1. Push the rack mount brackets (RM-1 1) upwards until it is firmly attached to the receiver . (Figure 5) Figure 5 B. Setup for dual half-rack receivers 1. Remove the screws at the top and bottom of the receiver where they will be joined together .
brackets (RM-12) on the outer sides of both receivers as shown in Figure 6. Figure 6 4. After completion, it can be rackmounted into an EIA standard rack case. Shown in Figure 7. 5. Make sure that the system performs correctly by placing the system away from noise sources.
4. OPERA TION INSTRUCTIONS 1. T urn the volume controls of the receiver and device in use to a minimum setting before turning on the microphone transmitter . After the receivers power switch is set to the on position, the power switch’s red indicator illuminates to denote normal power status.
microphone the AUDIO LED indicators will illuminate according to the strength of sound level. If the LEDs do not illuminate or sound is not present at the output, the system is not functioning properly and must be checked. 4. Receiver and Amplifier V olume Adjustment: a.
IN” input jack of the amplifier or mixer . Adjust the volume controls of the amplifier or mixer to the same desired level, then properly fine adjust the receiver volume control to match the same sensitivity as the wired microphone.
5. Caution 1. Since the installation of the antenna influences the operating efficiency of the receiver , the most important rule is to minimize the distance as much as possible between the receiving antenna and the microphone for the best reception and performance.
HANDHELD WIRELESS MICROPHONE The Peavey Pro Comm PCX-V12 handheld wireless microphone is a modular design. It also incorporates “Superior frequency tracking and muting techniques” dual- squelch to eliminate noise interference. 1. Unit Features and Functions 1.
2. BA TTER Y INSERTION 1. Unscrew the battery cap in a counter- clockwise direction. 2. Insert a 9V battery into the battery compartment according to the correct polarity as shown in Figure12. The moment the battery touches the terminals of the compartment, the indicator will flash briefly .
4. When the microphone is not in use make sure to turn it off to extend the battery life. Remove the battery from the battery compartment if the microphone will not be in use for a long period of time. If a rechargeable battery is used take it out for a recharge as necessary .
4. Gain Control: Adjusts the input gain to an appropriate level. 5. T ransmitter Housing: Contains the PCB and battery . 6. Battery Status Indicator: Indicates the power on/off and battery status. a. When the power switch is turned on the LED indicator flashes briefly , indicating normal battery status .
1. Push down on the battery cover to open the battery compartment. 2. Insert a 9V battery into the battery compartment according to the correct polarity as shown in Figure 14. Then push up on the battery cover to close the battery compartment. 3. The LED indicator will flash briefly when power is turned on to indicate normal battery status.
3. AF 4-PIN INPUT CONNECTION METHODS 1. 2-Wire Electret condenser microphone Capsule 2. 3-Wire Electret condenser microphone Capsule 3. Dynamic Microphone 4.
SPECIFICA TIONS 1. Overall: VHF PCX-V12 1. Carrier Frequency Range: VHF Band 160~250 MHz 2. Oscillation Mode: Quartz-controlled 3. Channel: 1-channel fixed 4. Stability: + 0.005 % with temperature compensation 5. Max. Deviation: + 15 KHz with level limiting 6.
20 TROUBLESHOOTING GUIDE Symptom Distance Possible Possible Cause Solution No AF signal Any low transmitter replace battery and no RF signal battery voltage No AF signal long out of range move transmi.
NOTES: 21.
PEA VEY ELECTRONICS CORPORA TION LIMITED W ARRANTY Effective Date: July 1, 1998 What This Warranty Covers Y our Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.
IMPOR T ANT SAFETY INSTRUCTIONS W ARNING: When using electric products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water .
Features and specifications subject to change without notice. Peavey Electronics Corporations • 71 1 A Street • Meridian MS • 39301 • (601) 483-5365 • Fax 486-1278 ©2000.
Een belangrijk punt na aankoop van elk apparaat Peavey PCX-V12 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Peavey PCX-V12 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Peavey PCX-V12 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Peavey PCX-V12 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Peavey PCX-V12 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Peavey PCX-V12 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Peavey PCX-V12 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Peavey PCX-V12 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
