Gebruiksaanwijzing /service van het product C1306M-D (7/09) van de fabrikant Pelco
Ga naar pagina of 24
INSTALLATION C1306M-D (7/09) ExSite ® EHXM Series Explosionproof Fixed Sy stem.
2 C1306M-D (7/09) Contents Important Safe ty Instruct ions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting Started .
C1306M-D (7/09) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed al l warnings. 4. Follow all instructions. 5. Do not bl ock any ven tilation openings. Ins tall in accordance with the manu facturer’ s instructions.
4 C1306M-D (7/09) Getting Started Thank you for pu rchasing Pe lco’ s ExSite ® EHXM Series explosionproof system. This manu al in cludes in structio ns for i n stalling all th e components of the system.
C1306M-D (7/09) 5 Install the Power Module Attach the power module to the mo unting surface. Use only insta llation methods and materials capa ble of supporting fou r times t he maximum specified load o f the system (140 lb /63.
6 C1306M-D (7/09) CONNECT WIRING Refer to the following informa tion to connect the wires an d cables as required. NOTES: • Relay 3 is a llocated spe cif ically for an external wash er (n ot supplied by Pelco). • All relays are specifie d for 32 VDC, 0.
C1306M-D (7/09) 7 DIP SWITCH SETTINGS Configure the receiver address, termination, and baud se tting for the system. The DIP switches to configure th ese settings are located on the to p of the power module. NOTE: No DIP switch settings are re quired for Coaxitron contr ol.
8 C1306M-D (7/09) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF O FF OFF OFF 2 ON OFF OFF OFF OFF OFF OF F OFF 3 OFF ON OFF OFF OFF OFF OF F OFF 4 ON ON .
C1306M-D (7/09) 9 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 49 ON OFF OF F OFF ON ON OFF OF F 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF ON .
10 C1306M-D (7/09) T able B. D Protocol Receiver Address (Continued) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 143 ON ON ON ON OFF OF F OFF ON 144 OFF OFF OFF OFF ON OFF O.
C1306M-D (7/09) 11 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 2 3 9 O NO NO NO N O F F O NO NO N 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON O.
12 C1306M-D (7/09) Install the Camera Module T o install the camera mo dule, do th e follo wing: 1. Refer to Figure 4. Loose n the set sc rew at the b ack of the c amera enclosu re with the pr ovided 1.5 mm A llen wrench. Figure 4. Loosen Set Screw 2.
C1306M-D (7/09) 13 3. Slide th e camera modul e into the camera enclos ure. Refer t o Figure 6 to position th e camera modul e properly in the came ra encl osur e. Carefully mate the camer a’ s power connector to the mating con nector located inside the camera enclos ure.
14 C1306M-D (7/09) 4. Models with a wiper: Refer to Figure 8 and do the fo llowing to in stall the ar m of the wipe r: a. Place the su pplied gree n bushing on the stud l ocated be hind the ha ndle of the camera module . The bushin g should be in the sam e orientatio n as shown in Figure 8.
C1306M-D (7/09) 15 Install the Enclosure and Set Pan Position 1. Check fo r proper se ating of t he power modu le seal. Make sure the se al is fully seated in t he groove o n the top of the powe r m odule. Figure 9. Factory-Installed Power Module Seal 2.
16 C1306M-D (7/09) Set the T ilt Angle of the Camera Module 1. Place a 41 mm open end or crescent wrench on the tilt locking nu t and a 21 mm open end wre nch on the tilt shaft (refer to Fig ure 11).
C1306M-D (7/09) 17 Install the Sun Shroud 1. Place the supplied nylon washer s on the 6-32 Phillips pan head screws. Refer to Figure 12. 2. Align the moun ting holes of the sun shroud with the holes on top of th e camera enclosure. 3. Use the supplied nylo n washers and screws t o secure the sun shroud to th e camera enclosure.
18 C1306M-D (7/09) Maintenance CAMERA MODULE REPLACEMENT T o replace t he camera mod ule, do the f ollowing: 1. Remove the back cap of the came ra enclosure. Refer to Figur e 13 and do the following: a. Loosen the set screw with a 1 .5 mm Allen wren ch.
C1306M-D (7/09) 19 3. Models with a wiper: Remove the wiper arm an d the green bushing from the unit (r efer to Figure 14 ). 4. Slide the camera modu le out of the enclosure. 5. Install th e new camera mo dule by doin g the follo wing: Slide the came ra module int o the camera enclosure.
20 C1306M-D (7/09) 6. Models with a wiper: Refer to Figure 14 and do the following to re install the arm of the wipe r: a. Reinstall the gree n bushing on the stud locate d behind the handle of the camera module.
C1306M-D (7/09) 21 Specifications ELECTRICAL Input Voltage 24 VAC or 100-240 V AC, 50/60 Hz Input V olt age Range ±10% Power Consumptio n Maximum 60 W (120 VA) per system Heater and Defroster Micropr.
22 C1306M-D (7/09) *Manual control of camera setup functio ns can be done with CM6700, CM 6800, CM8500, CM 9500, CM9740 , CM9760, CM9770, CM9780, KBD200A , KBD300A, and MPT 9500 control lers, but not with CM75 00, MPT9000, o r KBD9000 contr ollers.
The materials used in the manufacture of this documen t and it s components are compliant to the requirements of Directive 2002/9 5/EC. This equipment contains elec trical or electronic components tha.
Pelco, Inc. Worldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 292-1981 Fax +1 (559) 348-1120 www .
Een belangrijk punt na aankoop van elk apparaat Pelco C1306M-D (7/09) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pelco C1306M-D (7/09) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pelco C1306M-D (7/09) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pelco C1306M-D (7/09) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pelco C1306M-D (7/09) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pelco C1306M-D (7/09) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pelco C1306M-D (7/09) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pelco C1306M-D (7/09) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
