Gebruiksaanwijzing /service van het product DX8100 van de fabrikant Pelco
Ga naar pagina of 40
INSTALLATION C3648M (7/08) SCSI Card and External V ideo Storage DX8100 Series Digital V ideo Recorder.
2 C3648M (7/08) Contents Important Safe ty Instruct ions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Introduction .
C3648M (7/08) 3 List of Illustrations 1 Removing the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 Removing the Chassis Cover .
4 C3648M (7/08).
C3648M (7/08 ) 5 Important Safety Instructions The DX8100-ISCI SCSI card must be installed inside the DX8100 chassis. T o do so, the DX8100 must be taken offline and turned of f before starting the upgrad e process. Before contin uing the upgrad e procedure, read these safety instru ctions.
6 C3648M (7/08) Introduction Welcome to the extern al video sto rage upgrad e for the DX8100 Se ries digital video recorder (DVR). The exte rnal video storage up grade includes the DX8100-ISCI SCSI card an d the DX8100H DDI (Infortrend ® EonStor ® A12U- G2421).
C3648M (7/08 ) 7 Parts List and T ools DX8100-ISCI SCSI CARD T o install the DX8100 -ISCI SCSI card, you will also need a nonmagnetic Phill ips screwdriver #1, a properly grounded ESD wri st s trap and mat, and four small containers (optional ) to store s crews.
8 C3648M (7/08) OTHER DX8100 OPTIONAL ACCESSORIES The DX8108 b ase unit incl udes an 8-ch annel captu re card and the DX8116 ba se unit inclu des a 16-cha nnel capt ure card. NOTE: The DX8100-ISCI SCSI card option is not supported fo r DX8124 or DX 8132 models.
C3648M (7/08 ) 9 DX8100-ISCI SCSI Card Installation NOTE: When ordered together , the DX8100 and DX8100HDDI units come prec onfigured from the factory . The DX8100-ISCI SCSI card is alread y installed and the unit s are ready for installation. Procee d to Installing a New DX8100 and DX8100HDDI System on page 15.
10 C3648M (7/08) OPENING THE CHASSIS 1. Make su re you prot ect the un it and its components, which are susc eptible to d amage from imp roper hand ling and ES D. Refer to t he Safe Handling of Hard Drives documen t (C2668M) for more informatio n. 2. Use a Phillips screwdriver to remove the chassis cover (r efer to Figure 3): a.
C3648M (7/08 ) 11 UNDERSTANDING THE COMPONENT LAYOUT Figure 3 an d T able B provide i nformation about the D X8100’ s slot assignments a nd major compo nents.
12 C3648M (7/08) MOVING THE MAIN CAPTURE CARD In the DX8108 and DX8116 base DVRs, the main capt ure card is installed in slot 2. T o install the DX 8100-ISCI SCSI card, the mai n ca pture card must be moved from slot 2 to slot 3. The DX8100-ISCI SCSI card must be physically inst alled in slot 2.
C3648M (7/08 ) 13 2. Move the main capt ure card (ref er to Figure 5): a. Remove th e capture c ard from slo t 2 and fir mly seat th e capture c ard in th e PCI conne ctor for sl ot 3. b. Secure the ca pture card brac ket with the screw . c. Reconnect the 5-wir e TV/Audio cable.
14 C3648M (7/08) REASSEMBLING THE UNIT 1. Replace the chassi s cover using the screws you removed from the si des and rea r of the unit (refer to Figure 7) . Figure 7. Replacin g the C hassis C over 2. Attach the silver product label tha t came with your upgrade kit to the inside of your DVR’ s front door .
C3648M (7/08 ) 15 Installing a New DX8100 and DX8100HDDI System When ordered together , the DX8100 or DX8116 and DX8100HDDI unit s come preconfigured from the factory. The DX8100-ISCI SCSI card is already installed and th e units are ready for insta llation.
16 C3648M (7/08) 3. Install the drive t rays: a. On the DX8100HDDI front panel, place the drive tray 1 re le ase button in the unlocked position ( refer to F igure 10). Figure 10. Drive T ray Key-Lock in Unlocked Position b. Press t he relea se button ( refer to Figure 1 1).
C3648M (7/08 ) 17 CONNECTING THE DX8100 HDDI TO THE DX8100 Refer to Figure 13 to pe rform the following steps: 1. Plug one end of the VHDCI-to-V HDCI SCSI cable into port CH 1/ A on the DX8100-ISCI SCSI card. 2. Plug the other end of th e SCSI cable to the DX8100 HDDI CH0-In connector .
18 C3648M (7/08) Upgrading the DX8100 with the DX8100HDDI The DX8100HDD I upgrade co mes precon figured from the fa ctory and d oes not nee d to be conf igured dur ing the i nstallation process. However , you need to configure the DX8100 to recognize and work with the newly insta lled DX8100HDD I.
C3648M (7/08 ) 19 9. When the Computer Management window appea rs, click Disk Management. 10. If the “Initialize and Convert Di sk Wizard” appears, pe rf orm the following steps. Otherwise, go to step 11. Figure 16. Initialize and Convert Disk Wizard a.
20 C3648M (7/08) d. Disk status appear s in the contents pane . For this exam ple, there are five unallo cated dynamic driv es. Perfo rm the followi ng steps: (1) Right-click a disk in the Disk sta tus pane (o ne that is l abeled Dynamic). A shortcut menu appears.
C3648M (7/08 ) 21 a. Configure an y unallocated drive s. (1) Right-click the fi rst unforma tted disk in the conten ts pane (l abeled Un allocated). A shortcut me nu appears. (2) Click New Partition. Figure 20. Unallocated Dynamic Drives b. Perform a quick format .
22 C3648M (7/08) 12. Repeat step 11 unt il all unfo rmatted dis ks are fo rmatted. Once formatted, the disk st atus change s from Unal located to Health y.
C3648M (7/08 ) 23 15. Click Close to exit the Comp ut er Management application. 16. Start t he Allocati on Manage ment appli cation. a. Go to Start > Run. The Run dialog b ox appears. b. In the Open drop-down box, type allocreset . c. Click OK. 17.
24 C3648M (7/08) 20. If you are s toring video d ata on the DX8100 intern al HDDs and th e DX8100HDDI, c lick the Recovery b utton. Figure 26. Selecting the Recovery Option 21. Click the plus (+) to display the available pa rtitions. Figure 27. Viewing A vailable Partitions 22.
C3648M (7/08 ) 25 23. Repeat step 22 u ntil all part itions are set to All ocation. 24. After all part itions are set to Allocation, click “Begin allocation.
26 C3648M (7/08) Upgrading the DX8100HDDI HDD Storage Capacity The DX8100HDD I must be reco nfigured when upgrading the storag e capacity. BACKING UP RECORDED VI DEO DATA (OPTIONAL) 1.
C3648M (7/08 ) 27 6. At the command promp t, type telnet and the DX81 00HDDI’ s IP addre ss obtained in step 4c, and then pr ess Enter . Figure 30. Entering the T elnet IP Address 7. When prompted for the password, pr ess Enter again. 8. Press Esc on the keyboa rd to cl ose any mess ages.
28 C3648M (7/08) Figure 32. Unmapping Partitions 11. On the keyboard, pr ess Esc twice to return to the Ma in Menu. 12. Select “v iew and edi t Logical drive s,” and then press Ente r .
C3648M (7/08 ) 29 a. V erify that the active Logical D rive is selected, and then press En ter . b. Choose “Delete logical drive,” and then press Ente r . Figure 34. Delete Logical Drive c. Select Y es on the shortcut me nu, and then p ress Enter .
30 C3648M (7/08) 19. Press and hold EN T for two second s to initialize the logical drive. Figure 36. Initializi ng Logical Drive UNMAP THE LOGICAL DRIVE 20. After the logical drive is initia lized, press the down arro w three times until “View an d Edit Host Luns” appears.
C3648M (7/08 ) 31 PARTITIONING THE LOGICAL DRIVE 27. On the keyboard, pr ess Esc to close any message s. The Main Menu appe ars. 28. Select PC Graphi c <ANSI Mode >, and then press En ter . Figure 39. PC G raphic ANSI Mode 29. From the Main Menu, select “view and edit Logical d rives,” and then pre ss Enter .
32 C3648M (7/08) 31. Select “P artition logical driv e” on the shortcut me nu, and the n press Ente r . Figure 42. Partition Logical Drive 32. A warning me ssage. Select Y e s, and th en press Ente r . Figure 43. Partition Logical Drive W arning 33.
C3648M (7/08 ) 33 c. A warning message ap pears. Select Y es, and then press Enter . Figure 45. Starting the Partition Process 34. Set the part ition size for the re maining logica l drives: a. In the logical drives table, select the next logi cal drive i n the list.
34 C3648M (7/08) MAPPING THE PARTITIONS 37. From the Main Me nu, select “view and edit Host luns,” and th en press Enter . A shortcut menu ap pears. Figure 48. Main Menu 38. Select “CH L 0 ID 0” an d press Ent er . A s econd shortcu t menu appea rs.
C3648M (7/08 ) 35 40. Press Enter fou r times. 41. The Map L ogical Driv e prompt appe ars. Select Y es, and then press Ente r . Figure 50. Accepting LUN 0 (Zero) Mapping Settings 42. Select LU N 1, and t hen press E nter twice . 43. Select the next availab le partit ion, and then press E nter twice.
36 C3648M (7/08) 46. After all partit ions are mapped , press Esc on the keyboard to re turn to the Main Me nu, and then close the comma nd prompt. Figure 53. LUN Mapping FORMATTING THE DRIVES 47. Return to the DX81 00HDDI front panel an d press ESC five times.
C3648M (7/08 ) 37 55. T o perform a quick for mat: a. Click Next four times. b. Click the “Perform a quick format” check box. c. Click Next, and then click Finish. 56. Repeat step 54 unt il all driv es are forma tted. Once f ormatted, th e disk stat us changes f rom Unallocat ed to Healt hy .
38 C3648M (7/08) Specifications ELECTRICAL Input V olt age 100 V AC (at 6 A ) to 240 V AC (at 3 A ) ± 10%, 50/60 Hz, with PFC (autoswitching) Cable T ype 2 USA (117 V AC), 2 Eur opean (220 V AC), 2 UK (250 V AC) All, 3 prongs, molded conn ector , 6 ft (1.
PRODUCT W ARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without c harge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Australia | Finland | France | G ermany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Arab Emirates | United Kingdom | United States W orldwide Headquar.
Een belangrijk punt na aankoop van elk apparaat Pelco DX8100 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pelco DX8100 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pelco DX8100 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pelco DX8100 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pelco DX8100 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pelco DX8100 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pelco DX8100 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pelco DX8100 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
