Gebruiksaanwijzing /service van het product 620001 van de fabrikant Pentair
Ga naar pagina of 16
Rev. A 1-18-06 1 P/N 620001 Hydrel Fixture Housing - Rust Staining Repair Instructions Before installing this product, read and follow all warning notices and instructions accompanying this product. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage.
P/N 620001 2 Rev. A 1-18-06 SECTION I. FIXTURE HOUSING ENTR Y HUB REP AIR INSTRUCTIONS. STEP 1 Before starting repair , ensure that the inside of the fixture housing has the same style entry hub as shown in Figure 1. It is necessary to verify the correct style entry hub for this warranty repair .
Rev. A 1-18-06 3 P/N 620001 Fixtur e Housing Entry Hub Repair Instructions. STEP 2 1. If there is no internal bond wire as shown, skip to STEP 3. 2 . If there is an internal bond wire or a non-listed potting material around the bond post, remove the potting material completely.
P/N 620001 4 Rev. A 1-18-06 Fixtur e Housing Entry Hub Repair Instructions. STEP 3 If there is no internal bond wire in the conduit, the fixture housing will appear as shown in Figure 3. hn-03-11-16-98 No bond wire in conduit unused bond screw . Figure 3.
Rev. A 1-18-06 5 P/N 620001 Fixtur e Housing Entry Hub Repair Instructions. Working with muriatic acid can be dangerous. When cleaning elements always wear rubber gloves and eye protection. Add acid to water, do not add water to acid. Splashing or spilling acid can cause severe personal injury and/or property damage.
P/N 620001 6 Rev. A 1-18-06 Fixtur e Housing Entry Hub Repair Instructions. STEP 5. 1. Attach an anode block, (with an allen head set screw), installed directly to one of the two unused posts on the hub ring. a. This is done by pushing the center hole of the block firmly and completely over the post, press-fitting it into place.
Rev. A 1-18-06 7 P/N 620001 Fixtur e Housing Entry Hub Repair Instructions. STEP 6. 1. After fully pressing the anode block into place, tighten the set screw with a 3/32 inch allen wrench, see Figure 6. a. The allen wrench is not supplied with the kit.
P/N 620001 8 Rev. A 1-18-06 Fixtur e Housing Entry Hub Repair Instructions. STEP 7 1. If a bonding wire is connected to the bonding lug in the fixture housing cover this connection with a listed potting compound, (Scotchcast 2134 or equivelant). a. This will require the pool water level to be lowered and the potted area dried.
Rev. A 1-18-06 9 P/N 620001 SECTION II. AL TERNA TE REP AIR INSTRUCTIONS, BEFORE 1998. This repair procedure can be used both for small fixture housings and for those with angled conduit hubs. STEP 1. Before starting repair , ensure that the inside of the fixture housing has the same style entry hub as shown in Figure 1.
P/N 620001 1 0 Rev. A 1-18-06 Working with muriatic acid can be dangerous. When cleaning elements always wear rubber gloves and eye protection. Add acid to water, do not add water to acid. Splashing or spilling acid can cause severe personal injury and/or property damage.
Rev. A 1-18-06 1 1 P/N 620001 Alternate Repair Instructions STEP 3 1. Attach No. 8 copper jumper wire to one of the two unused posts on the hub ring. a. Place the ring over the post, and press the jumper wire in the gap between the ring and post opposite the ring set screw.
P/N 620001 1 2 Rev. A 1-18-06 Alternate Repair Instructions STEP 4 1. Attach the anode asssembly to the jumper wire using the mechnical lug. 2. Tighten all the screws firmly. 3. Position the anode to clear the light fixture and the cord, and to be away from the entry hub.
Rev. A 1-18-06 1 3 P/N 620001 Alternate Repair Instructions STEP 5 1. Completely cover the entire entry hub, the bond wire and the post clamp with two parts underwater epoxy putty, (supplied with this kit), to at least 1/4 inch thickness.
P/N 620001 1 4 Rev. A 1-18-06 Alternate Repair Instructions STEP 6 If there is no internal bond wire in the conduit, the unused bond screw and hub can be used to attach the jumper wire. hn-03-11-16-98 No bond wire in conduit unused bond screw Figure 6.
Rev. A 1-18-06 1 5 P/N 620001 Alternate Repair Instructions STEP 7 1. Attach the No. 8 copper jumper wire to the unused bond lug and tighten the screw frimly. 2. Attach the anode assembly to the jumper wire using the mechanical lug. 3. Tighten all the screws firmly.
P/N 620001 1 6 Rev. A 1-18-06 Alternate Repair Instructions STEP 8 1. Completely cover the entire entry hub and the jumper wire connection with two parts of underwater epoxy putty, (supplied with this kit), to at least 1/4 inch thickness.
Een belangrijk punt na aankoop van elk apparaat Pentair 620001 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pentair 620001 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pentair 620001 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pentair 620001 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pentair 620001 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pentair 620001 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pentair 620001 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pentair 620001 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
