Gebruiksaanwijzing /service van het product TL7612 van de fabrikant AT&T
Ga naar pagina of 30
Quick start guide T L 7 6 1 2 D E C T 6 . 0 c o r d l e s s h e a d s e t a n d h a n d s e t l i f t er.
2 Avoid placing the headset base too close t o: • Communication devices such as television sets, VCRs or other cordl ess telephones. • Excessive heat sources. • Noise sources such as a window with traffic outside, motors, microwav e ovens, refrigerator s or fluor escent lighting.
1 Quick r ef er ence guide - headset ON/OFF light status On Headset is charging in the headset base. Headset is trying to r egister to the headset base. Headset is searching for the headset base. • • • Flashing Flashes slowly when an incorr ect type of battery is installed.
2 Quick r ef er ence guide - headset V OL U ME / + - Press the volume k eys on the side of the headset to adjust the listening volume when on a call. MUTE/FLASH Press to mut e the microphone during a call. Press and hold to answer a call waiting call while on a call.
3 Three quick beeps VOL UME / + - keys ar e pressed when the volume is already at its highest or lowest setting. The headset is not regist ered and the headset ON/ OFF button was pr essed. The headset is out of range from the headset base during a call.
4 Quick r ef er ence guide - headset base Charging cr adle Insert the headset here for char ging . P AIR Press to r egister or deregister the headset. NO LIFTER MODE light On when NO LIFTER MODE is selected. Flashes while on a call, or another telephone is in use on the same line.
5 V OL U ME / Pr ess th e vol um e k ey s on t h e si de of th e hea ds et ba s e to ad ju s t th e s pe ak in g vo lum e w hi le on a c a ll . LIFTER AUDIO AD JUST Swi tch to choo se t he be st h eadse t au dio qual ity when usin g LI FTER MODE .
6 NO LIFTER MODE On when NO LIFTER MODE is selected (default mode). Flashes quickly when there is an incoming call. Flashes when the headset is in use or another telephone on the same line is in use. • • • LIFTER MODE On when LIFTER MODE is selected.
7 Swit ch hook presser W h e n t h e C O R D E D H A N D S E T C O N N E C T E D switch is set to YES , pre ssin g ON /OFF on the headset raises or lowers the switch hook presser . Lifter contr ol cable Th is c abl e is h ar d w ir ed i nt o th e lif t er an d pl ugs i nt o th e LI FT ER ja ck o n the he ad se t b as e.
8 Small lift er pad Holds the earpiece of the cor ded telephone handset. Adhesive tape Remove the pr otective strips befor e attaching the lifter t o the telephone base. ST A TUS light O n i n r e d w h en t h e r i n g de t e ct o r i s o f f . On in blue when the ring detector is on and the headset not in use.
9 ST A TUS light Quick r ef er ence guide - handset lift er Red O n w h e n th e h e ad s e t is n o t i n u se a n d t h e r in g d e t e c t o r i s t u r n ed o f f . F l as h e s sl o w l y w h e n t h e he a d s e t i s in u s e a n d t he r i n g d e t e c t o r i s t u r n ed o f f .
10 Bat t ery installation Install the battery as shown below . After installing the bat tery , you ma y be able to mak e and r eceive short calls. For optimal performance, charge the headset battery for at least six hours befor e use. When the headset is not in use, r echarge the headset by returning it to the headset base.
11 Bat t ery char ging After installing the batt ery, charge the headset by placing it on the headset base as shown below . The headset ON/OFF light is on when the headset is char ging. CAUTION: There may be a risk of detonation if you use a wrong type of batt ery .
12 Headset base and lift er install ation Installa tion prepar ation Befor e installing the headset base, r em ov e the r ear bo tt om pie c e of th e he ads et ba se by pu sh in g i t a wa y fr om th e ba s e (a s s ho wn in F ig ur e 1) . In st all t he he ad se t b as e a s sh ow n on t he fo ll owi ng p ag es .
13 Headset base and handset lift er install ation No lifter mode or lift er mode There are two answer modes available on the headset base. The current mode is indicated by the NO LIFTER MODE or LIFTER MODE lights on the front of the headset base.
14 Headset base and handset lift er install ation Cor d labels The cor ds pr ovided with your headset have colored labels attached to help you plug them int o the headset base.
15 Headset base and handset lift er install ation Installation options Y ou hav e three installation options: O pt i on 1 : Co nn ec t th e ha nd se t li ft e r t o a c o r d ed ph on e ( p ag e s 1 6 - 2 3) . Th i s o pt io n e n ab le s y ou to a n sw er ca ll s ev en if y ou a r e a w a y f r om th e t el e ph on e b as e.
16 Option 1: Connect the handset lifter t o a cor ded phone 1. Unplug the curly handset cor d from the telephone and plug it into the C U R L Y C O R D jack (light blue dot) on the headset base.
17 Adjust the cor ded handset audio 1. Make sur e that LIFTER MODE light on the headset base is on. Press the MODE button on the headset base t o change the mode. 2. Lift the corded handset t o release the switch hook. Place the cor ded handset aside.
18 At tach the lift er 1. T o choose where t o install the lifter on your telephone, look at the spac e underneath the corded handset. If ther e is a speaker , the lifter should be center ed over the speak er . If there is no speak er , the lifter should be cent ered within the space.
19 Headset base and handset lift er install ation Adjust the height of the lift er arm T urn th e AD JUS T LIF TER kno b t o c hang e t he h eig ht o f t he l ift er arm . Wh en in t he rai sed pos iti on, the ar m sh oul d r el eas e th e swi tch ho ok s o y ou can hea r a dia l t one .
20 Lifter adjustment s and testing 1. Make sur e that the headset base is set to LIFTER MODE and that the LIFTER AUDIO AD JUST setting is corr ect. 2. T urn the switch hook presser adjustment knob until the switch hook presser is just above the switch hook.
21 Headset base and handset lift er install ation Installation of lar ge lifter pad (optional) If th e sm all li ft er pa d can not ho ld th e c or ded ha nd se t st ea di ly , yo u ca n at ta ch a lar ge lif t er pa d ( pr ovi ded ) t o e nl ar ge the co nt act a r ea .
22 Inst all the auxiliary ring detector 1. Insert the auxiliary ring detector plug int o the RING DETECT jack on the lifter . 2. Remove the pr otective strip fr om the adhesive tape on the auxiliary ring detector . 3. Stick the auxiliary ring detector t o the center of the cor ded phone speaker .
23 Adjust the sensitivity lev el Th e de fault set ting of the ring detec tor work s with mos t co rded teleph ones . H owever , the ring detec tor might nee d s ome adju stme nts to r ecognize les s comm on t ele phone rin g ton es.
24 Headset base install ation Option 2: Connect the headset to a t elephone wall jack In or der to make calls using this installation option, you need a telephone plugged into the same telephone line or a dial pad (TL7601 pur chased separatel y). Mak e sure the headset base mode is set to NO LIFTER MODE .
25 Headset base install ation Opt ion 3: Conn ect the he adse t t o a c ord ed or c ord le ss phon e T o use this installation option, make sur e the headset base mode is set to NO LIFTER MODE . Plug one end of the telephone line cord int o the TEL WALL JACK (red dot) at the back of the headset base.
26 Headset oper ation Making a call When the headset base is connected to a cor ded handset of your telephone with the handset lifter inst alled (option 1): Y ou must select LIFTER MODE on the headset base. Pr es s on t he h ea d se t. T he s w it ch ho ok p re s se r ri se s a nd r el ea se s th e sw it c h ho ok .
27 Headset oper ation Answering a call on the headset When the headset base is connected to a cor ded handset of your telephone with the handset lifter inst alled (option 1): Press ON/ OFF on the headset. The switch hook pr esser rises and releases the swit ch hook.
www .telephones.at t.com © 2011 Advanced American T elephones. All Rights Reserv ed. A T&T and the A T&T logo are tr ademarks of A T&T Intellect ual Property lic ensed to Advanced American T elephones, San Antonio, TX 78219. Printed in China.
Een belangrijk punt na aankoop van elk apparaat AT&T TL7612 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen AT&T TL7612 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens AT&T TL7612 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding AT&T TL7612 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over AT&T TL7612 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van AT&T TL7612 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de AT&T TL7612 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met AT&T TL7612 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
