Gebruiksaanwijzing /service van het product SKAT-02 M van de fabrikant Atech Tech
Ga naar pagina of 22
Operating and Safety Instructions 1 PEGASUS-02 P / SKAT-02 P PEGASUS-02 M / SKAT-02 M MITER SAWS OPERATING AND SAFETY INSTRUCTIONS.
Operating and Safety Instructions 2 CONTENTS Page 1. General Information 3 1.1. Introduction 3 1.2. Manufacturer 3 2. Machine’s description and pur pose of use 3 2.1. Machine’s description 3 2.2. Technical features 5 2.3. Cutting diagra m 6 2.4. Overall di m ensions 7 2.
Operating and Safety Instructions 3 1. GENERAL INFORMATION 1.1. INTRODUCTION The user’s manual gi ven by the m anufactur er contains necessary information about the machine parts. Each m ach ine operat or should read these instructions carefully, and the machine should be operated aft er fully understanding the m .
Operating and Safety Instructions 4 Please mention the below mentioned data in all your correspondenc e regarding the machine with the m anufact urer and/or your ATECH dealer.
Operating and Safety Instructions 5 2.2. TECHNICAL FEATURES Technical Features (American) SKAT-02 P 3 HP 220V/440V 60Hz d=1 " D=16" 3000 rpm - - -- 26x24x30" 154 lbs SKAT-02 M 3 HP 220V/440V 60Hz d=1 " D=16" 3000 rpm 90-120 psi 0.
Operating and Safety Instructions 6 2.3. CUTTIN G DIAGRAM SKAT Cutting Diagram PEGASUS Cutting Diagram.
Operating and Safety Instructions 7 2.4. OVER ALL DIMENS IONS PEGASUS-02 M / SKAT-02 M PEGASUS- 02 P / SK AT-02 P.
Operating and Safety Instructions 8 2.5. PAR TS LIST AN D TECHNICAL DRA WINGS PEGASUS No. ORDER No. P ART NAME QTY 20 142-0 26 F ORK SHAFT 1 21 193-0 09 25x30x15 SI NTER BUSHE 2 22 177-0 23 F ORK ADJU.
Operating and Safety Instructions 9 SKAT No. Order No. PART NAME QTY 20 142-026 FORK SHAF T 1 21 193-009 2 5x30x15 SINTER BUSHE 2 22 177-023 FORK ADJUSTMENT PIN 2 24 112-104 MOT OR SHAF T PULLEY 1 26 .
Operating and Safety Instructions 10 3. SAFETY 3.1. SAFETY I NFORMATION The symbols shown hereunder are necessary to be read with special at tention. Not reading or observing of th em may cause da mage t o the equipment or pe rsonal injury.
Operating and Safety Instructions 11 3.2.4. Machine should be o perated only by staff mem b ers, who have read and understood the contents of th is manual. 3.2.5. All di rectives, recomme ndations a nd general safety rules contained in t his m anua l have to be observed fully.
Operating and Safety Instructions 12 3.3.9. Don’t use any materials other than those reco mmended by the manufacturer for cutting operations on the machine. 3.3. 10. Ensure that the work piece is cla mped appropriately by the m ach ine's clamp or vice.
Operating and Safety Instructions 13 5. INSTALL ATION OF THE MACHINE The m achine s hould be lo cated at least 40 cm i n front of the back wall . The machine is equipped with a burr coll ection bag connector and power supply s ocket on the back side. 5.
Operating and Safety Instructions 14 5.2. ELECTRI C CONNECTI ON 5.2.1. The three-phase power cable soc ket has to be in acc ordance with t he socket on the machine. 5.2.2. Use a connection cable socket in accordance with th e CE Saf ety Directives. 5.
Operating and Safety Instructions 15 The electric socket connectio ns have t o be checked and corrected by a qualif ied electrician. The rotation d irection o f the saw blade shoul d not be defi ned before testing. 6. MACHINE SAFETY I NFORMATION 6.8.1.
Operating and Safety Instructions 16 7. OPERATI ON The miter saws PEGASUS / SKAT cut non-ferrous aluminum, PVC profiles and PVC m aterials. The operator adjusts (manually via knob) the cutting speed of the saw blade according to the m at erial ty pe to be cut.
Operating and Safety Instructions 17 Illustration 3 7.1.1. Place the material t o be cut on the machine table, take the measur e the cutting length using the measuring tape on th e back fence, and cla mp the work piec e (pneumatically or manua lly). 7.
Operating and Safety Instructions 18 7.2. MITER CUT: 7.2.1 . Press the saw blade down unt il it touches the cutting slot of the tab le . 7.2.2 . Pull out the snap pin fr om its slot. (See Illustration 4) 7.2.3. Pull the table locking Bar to th e left to unlock.
Operating and Safety Instructions 19 Figure-4 Always ens ure that the clamps are pos itioned outside of the operation area of t he saw blade. 8. SAFE IN STALLATION OF THE SAW B LADE 8.1 To remove the circu lar saw blade from the b lade s haft, follow the instructions below.
Operating and Safety Instructions 20 8.1.8. Wh en replacing t he saw blade, use the part of the saw blade was her No. 48, which is in accordanc e with the s aw blade shaft diameter. The outer di ameter o f the blade w asher is 30 and 32 mm. . 9. MAINTENAN CE 9.
Operating and Safety Instructions 21 9.2. MAINT ENANCE AT THE END O F THE WORKING DAY 9.2.1. Disconnect electric and pneu matic connections. ( Main Switch must be on “0” position) 9.2.2. Remove all burr, chip and foreign materials from the machine surfac es.
Operating and Safety Instructions 22 11. ELECTRIC / PNEUMA TIC COMPONEN TS 11.1 ELECTRI C COMP ONENTS 11.2 PNEUMA TIC COMP ONENTS ORDER No. PART NAME QUANTITY 241-009 FRC-1/8-D-MINI CONDITIONER 1 241-023 SV- 1/4-3/ 2-D-O VALVE 1 550-003 PNEUMATIC CL AMP 2 ORDER No.
Een belangrijk punt na aankoop van elk apparaat Atech Tech SKAT-02 M (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Atech Tech SKAT-02 M heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Atech Tech SKAT-02 M vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Atech Tech SKAT-02 M leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Atech Tech SKAT-02 M krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Atech Tech SKAT-02 M bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Atech Tech SKAT-02 M kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Atech Tech SKAT-02 M . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
