Gebruiksaanwijzing /service van het product CM1164 van de fabrikant ATEN Technology
Ga naar pagina of 40
CM1164 4-port USB DVI-D KVMP Control Center RS-232 Commands V1.3 User Manual www.aten.com.
CM1164 RS-232 Control Tool 2 FCC Information This equipment has been tested and found to co mply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Ru les. The se limits ar e designed to provide reasonable protection against harmful interference in a resi dential installa tion.
CM1164 RS-232 Control Tool 3 RS-232 Operation Overview The CM1164’s built-in bi-directional RS-232 serial interface allows system control through a high-end control ler or PC. RS-232 serial operations in a CM1164 installation are manag ed via Hype rTerminal sessi ons on systems that are running Windows.
CM1164 RS-232 Control Tool 4 Console Login - Hy perT erminal Once a physical connection from the computer to th e CM1164 has been made, you can establish a HyperTerminal sessio n using the instructions below. 1. Open the HyperT erminal application, and configure the port settings for COM1 port, then click OK .
CM1164 RS-232 Control Tool 5 RS-232 Commands After you logi n via HyperTerminal (see Console Login - HyperTerminal , page 4), you can use the instru ctions below to send RS-232 comman ds to control the CM1164 from a remote system.
CM1164 RS-232 Control Tool 6 Login The Login command allows you to login to the CM1164 and begin sending RS- 232 commands. When y ou login the RS-232 l ink is “opened” and the CM11 64 will not respond to front panel pu shbuttons, hotkeys, OSD, or rem ote control commands - until the RS-232 link is closed (see Open/Clo se RS-232 Link , page 8).
CM1164 RS-232 Control Tool 7 Logout The Logout comm and allows you to logout of the CM1164 and cl ose the RS- 232 link. Use the Fo rmula - to set Parameters - to create a Command . Formulas: Command + [Enter] Parameters: Logout Comma nd The available formula for the Lo gout command is as follows: 1.
CM1164 RS-232 Control Tool 8 Open/Close RS-232 Link The Open/Close RS-232 Link command allows you to open/close the link between the computer sending RS-23 2 commands and the CM1164.
CM1164 RS-232 Control Tool 9 Switch Port The switch port command all ows you to switch between comput ers connected to the CM1164’s ports. Use the Formula - to set Parameters - to create a Command . Formula: Command + Input Comm and + [Enter] Parameters: Switch Port Commands Some available formulas for the Switch Port commands are as follows: 1.
CM1164 RS-232 Control Tool 10 PiP Mode The PiP Mode command allows you to ch ange the Picture in Picture display mode settings. Use the Fo rmula - to set Parameters - to create a Command .
CM1164 RS-232 Control Tool 11 PiP Mode Commands Some available formulas for PiP Mode commands are as follows: 1. Command + Config1 + Config2 + Config3 + Config4 + Config5 + [Enter] For example, to set Pi cture in Picture Dual Mode on Outpu t Channel 1 to Input Port 1, type the following: pip2 c1p1 [Enter] 2.
CM1164 RS-232 Control Tool 12 Quad V iew Mode The Quad View Mode command allows you to change the Quad View display mode settings. Use the Fo rmula - to set Parameters - to create a Command .
CM1164 RS-232 Control Tool 13 Change Display Mode The Change Display Mode command allow s you to change the Display mode being used. Use the Formula - to set Parameters - to create a Command . Formula: Command + Control + [Enter] Parameters: Change Display Mode Commands Some available formulas for Change Di splay Mode commands are as follow s: 1.
CM1164 RS-232 Control Tool 14 (Continued from previous page.) 2. Command + Control + [Enter] For example, to set Pictur e in Pict ure Triple displ ay mode, type the following: display pip3 [ Enter] Note: Each command string can be separated with a space.
CM1164 RS-232 Control Tool 15 Port Disable The Port Disable comm and allows you to disable a ports d isplay from being shown. Use the Formula - to set Parameters - to create a Command . Formula: Command + Control + Control + [Enter] Parameters: Port Disable Commands Some available formulas for Disabl e Port commands are as follows: 1.
CM1164 RS-232 Control Tool 16 OSD Language The OSD Language command allows you to chan ge the OSD language setting. Use the Formula - to set Parameters - to create a Command . Formula: Command + Cont rol + [Enter ] Parameters: OSD Language Commands Some available formulas for OSD Language commands are as follows: 1.
CM1164 RS-232 Control Tool 17 Keyboard Language Layout The Keyboard Languag e Layout command allows you to change the keyb oard language layout. Use the Formula - to set Parameters - to create a Command .
CM1164 RS-232 Control Tool 18 Set Operating System The Set Operating System command allows you to set the operating system for a port. Use the Formula - to set Parameters - to create a Command .
CM1164 RS-232 Control Tool 19 Auto Scan The Auto Scan command al lows you to set and enable Auto scan mode. Use the Formula - to set Parameters - to create a Command .
CM1164 RS-232 Control Tool 20 Port ID Display The Port ID Display comm and allows you to change the port ID numbers displayed for each port. Use the Formula - to set Parameters - to create a Command .
CM1164 RS-232 Control Tool 21 (Continued from previous page.) 3. Command + Control + Number + [Enter] For example, to set the port ID disp lay duration for 88 seconds, type the following: portid t88 [Enter] Note: Each command string can be separated with a space.
CM1164 RS-232 Control Tool 22 Security The Security command allo ws you to enable/disable and change security settings used to l ogin. Use the Formula - to set Parameters - to create a Command .
CM1164 RS-232 Control Tool 23 Security Commands Some available formulas for Secu rity commands are as follows: 1. Command + Control + [Enter] For example, to enable the secur ity function, type t he following: security on [Enter] 2.
CM1164 RS-232 Control Tool 24 Stat io n The Station command allows you to switch th e console focus to t he next station in a daisy chain setup. Use the Formula - to set Parameters - to create a Command . Formulas: Command + Control + Number + [Enter] Parameters: St ation Commands An available formula for the Station command is as follows: 1.
CM1164 RS-232 Control Tool 25 DCC Control The DCC Control command allows you to set the DCC Control mode. Use the Formula - to set Parameters - to create a Command . Formulas: Command + Control + [Enter] Parameters: DCC Control Commands Some available formulas for DCC Control commands are as follows: 1.
CM1164 RS-232 Control Tool 26 Mouse Emulation The Mouse Emulation command all ows you to set mouse emulation and mouse switching features. Use the Formula - to set Parameters - to create a Command .
CM1164 RS-232 Control Tool 27 Keyboard Emulation The Keyboard Emulation comm and allows you to enable/disabl e the keyboard emulation feature. Use the Formula - to set Parameters - to create a Command .
CM1164 RS-232 Control Tool 28 Video Dyna sync The Video Dynasync command allows yo u to set EDID settings. Use the Formula - to set Parameters - to create a Command . Formulas: Command + Cont rol + [Enter ] Parameters: Video Dy nasync Commands Some available formulas for Video Dynasync commands are as follows: 1.
CM1164 RS-232 Control Tool 29 Hardware Cursor The Hardware Cursor comm and allows you to enable/disable the hardware cursor feature. Use the Formula - to set Parameters - to create a Co mmand . Formulas: Command + Control + [Enter] Parameters: Hardware Cursor Commands Some available formulas for Hardware Cursor commands are as follows: 1.
CM1164 RS-232 Control Tool 30 Activate Beeper The Activate Beeper command allows you to enable/disable the beeper function. Use the Formula - to set Parameters - to create a Command . Formulas: Command + Cont rol + [Enter ] Parameters: Activate Beeper Commands Some available formulas for Activat e Beeper commands are as follows: 1.
CM1164 RS-232 Control Tool 31 Hotkey Setting The Hotkey Sett ing command allows you to enab le/disable and chan ge the hotkey used to invoke the HSM (Hotkey Setting Mode).
CM1164 RS-232 Control Tool 32 OSD Hotkey The OSD Hotkey comm and allows you to change the hotkey used to invoke the OSD. Use th e Formula - to set Parameters - to create a Command . Formulas: Command + Cont rol + [Enter ] Parameters: OSD Hotkey Commands Some available formulas for OSD Hotkey commands are as follows: 1.
CM1164 RS-232 Control Tool 33 Power on Detection The Power on Detection command allows you to enable/disable the power on detection feature. Use the Formula - to set Parameters - to create a Command .
CM1164 RS-232 Control Tool 34 Fn Key The Fn Key com mand allows you to sav e and select Fn keys for a focused port s display settings. Use the Formula - to set Parameters - to create a Command .
CM1164 RS-232 Control Tool 35 USB Reset The USB Reset command allows you to reset the USB connection. Use the Formula - to set Parameters - to create a Command . Formulas: Command + Control + [Enter] Parameters: USB Reset Command The available formula for the US B Reset command is as follows: 1.
CM1164 RS-232 Control Tool 36 Restore Default V alue The Restore Default Value command allows you to reset all of the CM1164’s settings back to the default.
CM1164 RS-232 Control Tool 37 Firmware Upgrade The Firmware Upgrade comm and allows you to enable the firmware upgrade mode. Use the Formula - to set Parameters - to create a Command . Formulas: Command + Control + [Enter] Parameters: Firmware Upgrade Command The available formula for the Firmwa re Upgrade command is as follows: 1.
CM1164 RS-232 Control Tool 38 KVM St atus The KVM Status comman d allows you to display read -only information ab out the CM1164’s current confi guration status.
CM1164 RS-232 Control Tool 39 Hotkey List The Hotkey List comm and allows you to di splay a list of the KVM’s hot keys. Use the Formula - to set Parameters - to create a Command . Formulas: Command + [Enter] Parameters: Hotkey List Command The available formula for the Hotk ey List command is as follows: 1.
CM1164 RS-232 Control Tool 40 Info The Info command allows you to display the CM1164’s current firmware version and copyright information. Use the Formula - to set Parameters - to create a Comman d . Formulas: Command + [Enter] Parameters: Info Command The available formul a for the Info comm and is as follows: 1.
Een belangrijk punt na aankoop van elk apparaat ATEN Technology CM1164 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ATEN Technology CM1164 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ATEN Technology CM1164 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ATEN Technology CM1164 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ATEN Technology CM1164 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ATEN Technology CM1164 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ATEN Technology CM1164 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ATEN Technology CM1164 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
