Gebruiksaanwijzing /service van het product FPS-1101 van de fabrikant Planet Technology
Ga naar pagina of 83
10/100 Mbps Direct Attached Print Server FPS-1101 User’s Manual 1.
Copyright (C) 2006 PLANET Technology Corp. All rights reserved. The products and programs described in this Us er’s Manual are licensed products of PLANET Technology, This User’s Manual contai ns proprietary information protec ted by copyright, and this User’s Manual and all accompanying hardware, softw are, and documentation are copyrighted.
T ABLE OF C ONTENTS INTRODUCTION ............................................................................................................................................................... 5 P RODUCT O VERVIEW .....................................
G ENERAL T ROUBLESHOOTING O VERVIEW .................................................................................................................... 66 P OWER R ELATED P ROBLEMS .....................................................................
Introduction Product Overview The external print servers enhance capability by le tting you place your printers at convenient locations directly on the Ethernet network, and by increasing network printer performance and management. Please note that t he print server does not support printing with host-based printers, e.
LED Indicators LED State Indication Status Blinking for POST (Yellow) When power switched on, the Status indicator will flash five times, and then on. 100Mbps On (Green) LAN Port has a valid network connection at 100Mbps. 10Mbps On (Yellow) LAN Port has a valid network connection at 10Mbps.
Reset Button To p r i n t e r Network Environment Wired Network w ith Print Server: Printer Print Server Computer Computer C omputer HUB 7.
2 . P rint S erver I nstallation Preparation To meet users’ network printing needs in today’s heterogeneous and multiple protocol networking environments, the print server suppor ts industrial standard protocols, including TCP/IP, IPX/SPX, NetBEUI and AppleTalk.
Windows NT/2000/XP/2003 Printing via the internet to Internet Printing Protocol- enabled print server Allows saving distribution of HQ hardcopy document over Internet, replacing fax, mail Comment Conf.
3. Software Installation The PSAdmin is a proprietary Windows-based m anagement program that can assist you in configuring and managing your print server in NetWare environments. The program can be installed from the setup CD of print server. Installing the PSAdmin and Print Server’s Driver 1.
3. Click Next , the wizard will automatically discover the print server. 4. From the Select A Print Sever screen, select the print server that you want to configure and click Next .
Click No if you want the print serv er to keep using the default IP address and keep the default settings: z IP address: 192.168.0.10 z Subnet Mask: 255.255.255.0 Click Yes if you want change IP address to the print server, and then click Next . Note: The IP address of print server must be within the same subnet as your network adapter.
13.
7. Click Add New Printer to launch Window s Add Printer Wizard . 8. Click Next and select Local Printer , make sure the Automatically detect and install my Plug and Play printer check box is NOT checked.
9. Make sure the Use the follow ing port radio-button is clicked and select LPT1: (recommended Printer Port) from the pull-down list. Then click Next .
11. If you already have the printer’ s driver installed, you will be a sked whether to keep it or to replace it. Click Next . Supply a name for the printer and choose whether you want to make it your default printer.
15. Right-click, select Properties -> Ports and verify that the print server’s port appears. 16. Go to General ; click Print Test Page to verify the configuration.
If you want to install more print servers, st art setup wizard from your Windows Start menu: start -> All Programs -> Network Print Server -> PSWizard and repeat the installation procedure.
TCP/IP Wizard 1. Click Wizard button just like a picture ＜ ＞ .and select TCP/IP Wizard . 2 Select “ Obtain an IP address from DHCP server ”. If there is a DHCP server on your network. This option allows the print server to obtain IP-related settings automatically from your DHCP server.
7 Done NetWare Wizard 1. Log into your NetWare file server as a Supervisor (Admin.) or equivalent. 2. Click Wizard button just like a picture ＜ ＞ .and select NetWare Wizard , as follow picture. 3. Select the NetWare File Server to wh ich the print server device will be attached.
3. Select the print server that you wish to configure. 4. Click Properties in the tool bar and the following screen will appear, Properties button just like a picture ＜ ＞ , as follow picture. 5. Select NetWare and type in the Print server that created during PCONSOLE.
Obtain an IP address from a DHCP server: This option enables or disables the DHCP featur e of the print server. When this option is enabled, the print server will obtain an IP addre ss automatically from the DHCP server on your LAN. The default value is “ Disable ”.
Upgrade Upgrade allows the user to upgrade the print server device. In order to upgrade the unit please perform the steps as follows: 1. Click Upgrade button just like a picture ＜ ＞ , as shown as follow picture 2. S elect General Upgrade . Make sure that the upgrade file is located in the same directory as PSAdmin.
Note : Configure the print speed in the Advanced label, must match the printer’s speed which connect to the print server. Undependabl e configuration will cause printer to abnormal printing. Multiple Print Queues Configuration To configure the print server to service mult iple print queues, please follow the instructions listed below: 1.
3. Click Change or Remove Programs tab. 4. Select Network Print Monitor for Window s 95/98/NT/2000/XP/2003 and click Change/Remove button. 5. The un-installation wiz ard program will be launched. 6. Follow the directions on the screen to complete the un-installation procedure.
4.I nternet P rinter C onnection and HP W eb J etAdmin IPP Overview Print server(s) support the Internet Printing Pr otocol (IPP). Using the appropriate software on your system, you can create an IPP print path from your system as Windows PC over the Internet.
6. In URL’s box, input print server’s IP address, for example, http://192.168.10.182/lp1. Then Click Next . ** One port should be the port name as lp1. 7. It will check print server to connect to HP pr inter, if not, it will appear as follow picture.
10. Click Finish button. 11. Done. HP Web JetAdmin Overvie w HP Web JetAdmin allows you to use a Web browse to revise, view, manage and diagnose devices connected to the print server or any standard printer MIB devices. For more information about a procedure or Window s in the HP Web JetAdmin software, see about HP’s relation document.
Download the installation files from HP Customer Care Online at http://www.hp.com/go/webjetadmin/ . Follow the instructions on the screen to in stall the HP Web JetAdmin software. Note: Installation instructions are also contained in the HP Web JetAdmin install file.
5. C onfiguration from E mbedded W eb S erver Overview The Print Server contains an embedded web server that can be accessed through a supported web browser on a LAN, for exampl e, IE 4.
Print Server Name: This option allows you to view device name of the print server. To correct the print server’s device name. System Contact: This option allows you to view contact name of the print server. To check the print server’s contact name who in charge of this device.
Printer Status 1.Click Status , it then appears the sub-menu. 2.Click Printer , it then as shown in the following picture. Manufacturer: This option allows you to view manufac turer of the printer. When the printer connected with the print server, it will be show in the manufacture box.
Use DHCP/BOOTP: This option allows you to view DHCP/ BOOTP status. If there is a DHCP/BOOTP server on your network, this option allows the print server to obtain IP-related settings automatically from your DHCP server. IP Address: This option allows you to view IP addr ess from the print server.
General Settings: Print Server Name: This option allows you to view print server’s name would be configured by PSAdmin utility. Polling Time: This option allows you to view polli ng time from the print server. This function is search for NetWare Server by per time .
AppleTalk Status 1.Click Status , it then appears the sub-menu. 2.Click AppleTalk , it then as shown in the following picture. AppleTalk Settings: If no any zone exists, the print server itself displays the zone name as an asterisk ( * ) in the current AppleTalk Status of the print server in the web browser.
SNMP Communities: This option allows you to view SNMP communities from the print server. There are two communities that control message from the network management of the print server. SNMP Traps: This option allows you to view SNMP traps from the print server.
Shared Name: This option allows you to view the Shared Name from the print server. Setup Menu Meanwhile, you have finished the IP address conf iguration with print server.
Email Alert: This option allows you to Enable/Disable the Email Alert support. SMTP Server IP Address: This option allows you to input the IP address of your Email SMTP server. Administrator E-mail Address: This option allows you to input your Email address that you want to receive the notification by Email.
TCP/IP Setup: 3. Click Setup , it then appears the sub-menu. 4. Click TCP/IP , it then as shown in the following picture. DHCP/BOOTP: This option allows you to select DHCP/ BOOTP option. If there is a DHCP/BOOTP server on your network. This option allows the print server to obtain IP-related settings automatically from your DHCP server.
NetWare Setup 1.Log into your NetWare file server as a Supervisor (Admin.) or equivalent. 2. Select NetWare and type in the Print se rver that created during PCONSOLE Select the NetWare File Server to which the print server device will be attached. 3.
Logon Password: This option allows you to input encry pted password from the print server. The print server login to NetWare se rver that administrator set password from selected print server. Use NDS Mode: To Enable NDS Mode, if you want to setup NDS environment.
4. Add or Modify the “ SET BINDERY CONTEXT = ” line to include the NDS organization (O) and all organization unit (OU) objects where users are located. For example: SET BINDERY CONTEXT = O=ABC; OU=SALES.OU=ABC-USA.O=ABC; OU=TECH.OU=ABC-USA.O=ABC ; 5.
3. Zone Name: In this option, type an AppleTalk Zone name that you want the print server to belong to or leave it in default (This enables the print server automatically search and link itself to the default zone that is set on the AppleTalk router, if found) .
Note: If you select a Zone that the PRINT SERVER doesn’t belong to, as you specified in the previous section, no print server will be displayed in the Step 4.
When an unusual condition or activity occu rs, the SNMP agent alerts the SNMP manager through SNMP traps . Following list summaries SNMP trap messages that the print server will send out.
SNMP Community: The print server supports up to two community names. The default community name is public (case-sensitive), with Read Only access right in default. Support HP WebJetAdmin: This option allows user determine to disable/enable the Support HP WebJetAdmin.
3. Workgroup Name: This option allows you to assign a workgroup name to print server on the Network Neighborhood. Windows uses it to identify the print server on the Network. 4. Shared Name: This option allows you to assign a name to print server’s port.
6. Network Print Monitor Preparation The print server supports TCP/IP , IPX/SPX and NetBEUI protocols under Windows 95/98/Me. Please make sure that the fo llowing steps have been completed before proceeding with installation under Windows PC. Select A Desired Protocol TCP/IP The TCP/IP Protocol must be installed.
TCP/IP Protocol Installation 1. Click Start , point to Settings and select Control Panel . 2. Double click the Network icon. 3. If the TCP/IP Protocol is not already installed, click Add . 4. Select Protocol and click Add . 5. Select Microsoft from the Manufacturers list.
NetBEUI Protocol Installation 1. Click Start , point to Settings , and select Control Panel . 2. Double click the Network icon. 3. If the NetBEUI is not already installed, click Add . 4. Select Protocol and click Add . 5. Select Microsoft from the Manufacturers list.
10. A message reading, “After your printer is in stalled, Windows can prin t a test page so you can confirm that the printer is set up properly.” Select No and click Finish . 11. Double-click the newly created Printer Name icon. 12. Select Printer and Properties .
By default, the computer will first search for the print server(s) on the network by using the IPX/SPX protocol. If the IPX/SPX protocol is inst alled, the print server will be displayed along with its Node ID, as shown in Node column. (The last 6 digits of the Node ID, located on the back of the print server unit) .
7. TCP/IP LPR Port Printing Installation Basic TCP/IP Installation Overview When installing your print server in a TCP/IP environment, IP addresses are essential as a basic means of communications. It is therefor e necessary to first assign an IP address to your print server unit.
5. From the Printer Ports box as shown in the following picture, select the LPR Port . 6. The Add LPR compatible printers box will then appear as shown in the following picture. Type in the IP address assigned to the print server in the Name or address of server providing lpd box.
Windows 2000/XP/2003 Standard TCP/IP Port Printing Installation 1. C lick Start , point to Settings , and select Printer . 2. Run Add Printer , Click Next .
6. In the Add Standard TCP/IP Printer Port Wizard box as shown in t he following picture, Select Custom , Click Settings button, and click Next . 7. In the Configure Standard TCP/IP Port Monitor box as shown in the following picture, select LPR form Protocol, type in a queue name, for example, lp1.
10. Select the appropriate printer manuf acturer and printer type list and click Next . 11. Type in a new Printer name or leave it in default, and click Next button. 12. A message reading, “To confirm that the printer is installed properly, you can print a test page”.
UNIX Installation After the static IP address is assigned, the Prin t Server is ready to be configured. For some UNIX/Linux systems, we include the detailed installation procedures below.
Basically, the Linux's printing system is based on BSD system. Although many commercial Linux systems are available in the market and their commands will vary slightly, depending upon which version is used, the functionality of the Linux-based variants is exactly the same.
7. Click Forward button. 8. In the Name field, type a user-defined name, click Forward . 60.
9. In the Queue Type field, choose Networked UNIX . 10. In the Server field, type the IP address of print server 11. In the Queue field, type a print server’s port name, which connect to the printer. For example: lp1. 12. Click Forw ard button. 13. In the Printer field, choose Postscript Printer .
15. Done. 62.
8.U pgrading P rint S erver Overview Upgrading print server will allow you to upgrade it s firmware inside the print server while the newer software version of the print server is available from your local dealer.
3. Wait for the transfer successful message. 4. Done. Upgrading the print server from UNIX (Through TCP/IP) 1. Log in as root 2. Ensure binary file is located in your current working directory. 3. Type “ tftp <print server’s IP address> ”.
4. Click Browse… and select the firmware file. 5. Click Upgrade . 6. Done. 65.
9. T roubleshooting General Troubleshooting Overview The most common problems, which cause the print server to perform improperly, are covered in this chapter. If a problem still exists after reading this chapter, please contact your dealer for technical support.
Windows 95/98/Me/NT/2000/XP/2003 Troubleshooting Multi-Segment LAN Environment Installation (through the Network Print Port) If your print server and Windows 95/98/Me/N T/2000/XP/2003 are located on t.
Moving the print server to A New Segment If the print server is moved from one network s egment to another after t he initial installation, through the Network Print Port, the print server must be rec.
Moving Your Computer to A New Segment If you are using the print server through the Network Print Port on your NT or Windows 95/98/Me computer and your computer is going to be moved onto another segment, you have to reconfigure the print server on your com puter to use your print server.
If this is the case, please consult your netwo rk administrator to obtain an unused IP address for your print server. C. The print server is on one segment and your Windows NT server is on the other segment.
6. In your editor, modify " BoxIPAddress " field from "0.0.0.0" to "192.72.214.100". Leave other options as default and do not change their values . When done, save this new file and quit from your editor. Please note, in this step you must specify an IP address which is valid on Segment B, such as 192.
Appendix: Rendezvous with Mac OS X 10.3.7 1. Enable the Rendezvous settings from t he print server’s WEB configuration. 2. Click " Printer Setup Utility ” from the bottom toolbox of Mac.
3. Click " Add ". 73.
4. Choose " Rendezvous ", and then Mac OS will automatically search the print server on the network. 5. Choose the proper printer model that c onnected to print server, and then click " Add ".
6. Now the network printer with Rende zvous has been successfully installed. SMB Printing with Windows XP 1. Enable the SMB settings from the print server’s WEB configuration. Assume your computers use the “ WORKGROUP ” as the SMB workgroup name in Windows.
2. Now you can find the print server from the SMB workgroup of Windows. Then, double click it. 3. Double click it again. 76.
4. Now you have to install the printer’s driver. 5. Choose it from the “Add Printer Wizard”. 77.
6. Install printer successfully. 7. Now, you can find your printer’s ic on and you can use the SMB printing mode. 78.
Reset Button Reboot the Print server : 1. Verify the power of print server is turned on. 2. Press the reset button once, and then release it. WARNING: This will restart the print serv er and stop all on-going and pending print jobs! Perform a Factory Default : 1.
Reset Button To p r i n t e r 80.
Frequently Asked Questions Question A Print jobs are sent to the print queue successf ully, but fail to be sent to the printer. Possible explanations 1. The Print server Name/Print Queue c onfiguration in PCONSOLE is incorrect. 2. The Print server name specified and stored in the print server memory doesn’t match the same one set in PCONSOLE.
Question D The Status LED light keeps blinking after POST. Possible explanation and solution The last upgrade process was not completed. The print server must be upgraded again by using the PSAdmin.
Additional Installation Instructions Panasonic KX-P6100/6300/6500 If you are using a Panasonic KX-P6100/6300/6500 lase r printer with the print server through the Network Print Port under Windows 95/9.
Een belangrijk punt na aankoop van elk apparaat Planet Technology FPS-1101 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Planet Technology FPS-1101 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Planet Technology FPS-1101 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Planet Technology FPS-1101 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Planet Technology FPS-1101 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Planet Technology FPS-1101 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Planet Technology FPS-1101 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Planet Technology FPS-1101 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
