Gebruiksaanwijzing /service van het product VIP-155PT van de fabrikant Planet Technology
Ga naar pagina of 61
SIP IP Phone VIP-155PT User’s manual.
Copyright Copyright (C) 2006 PLANET T echnology Corp. All rights reserved. The products and programs described in this User ’s Manu al are licensed products of PLANET T echnology , This User ’ s M.
3 Revision User ’s Manual for PLANET SIP IP Phone: Model: VIP-155PT Rev: 1.0 (October, 2006) Part No. EM-VIP155PTV1.
4 T ABLE OF CONTENTS Chapter 1 ................................................................................................ 6 Introduction ............................................................................................ 6 Overview ....
5 Syslog Config ........................................................................................................... 36 Ti m e S e t ...............................................................................................................
1 Chapter 1 Introduction Overview Meeting the next-generation Internet telephony service demands, PLANET T echnology provides feature-rich, toll-quality Internet telepho ny service solutions.
7 Configuration of the VIP-155PT can be perform ed in minutes via the keypad, or web interfaces. Using the built-in LCD display, the VIP-155PT o ffers u ser-friendly configuration guidelines, machine operation status, call status displays, and in coming call ide ntification.
8 Physical Det ails The following figure illustra tes the front/rear pa nel of VIP-155PT. Front View and Keypad function Front Panel of VIP-155PT Keyp ad Description 1 LCD Display Menu and all status shall be displayed for users. 2 Speed Dial No.1~No.
9 7 Redial Press to dial the last dialed number when the IP Phone is off-hooked. 8 PWR The green light goes on when power on. 9 Message The green light goes on-off when there i s an in comin g call. The light goes constant on when there have voice message (Proxy Mode.
Rear View 10 3 2 1 Rear Panel of VIP-155PT 1 LAN RJ-45 connector, to maintain t he exist ing network structure, connected directly to the PC through straight CAT-5 cable 2 WAN (PoE) RJ-45 connector, for Internet a ccess, connected directly to Sw it ch /H ub through straight CAT-5 cable.
2 Chapter 2 Prep arations & Inst allation Physical Inst allation Requirement This chapter illustrates ba si c installation of VIP-155PT • Network cables. Use standard 10/1 00Ba seT network (UTP) cables with RJ45 connectors. • TCP/IP protocol must be installed on all PCs.
Please locate your PC in the same network segment (192.168.0.x) of VIP-155PT. If you’re not familiar with TCP/IP, please refer to related chapter on user’s manual CD or consult your network administrator for proper network configurations.
Parameter Description Bridge Mode Enable this option to switch to b ridge mode. VIP-155PT won’t assign IP for its LAN port in bridge mode and its LAN and W AN port will be in the same network. IP address LAN IP addre ss of VIP-15 5PT Default: 192.168.
Connection Type Data required. St atic IP The ISP will assi gn IP Addres s, and related information. DHCP Get W AN IP Address automatically; it is no need to configure the DHCP settings.
15 Chapter 3 W eb Configurations Configuring and monitoring your VIP-155PT from web browser The VIP-155PT integrate s a web-based graphical user interface that can cover most configu r ations and machine st atu s monitoring. Via st andard, web browser , you can configu re and check machine status from anywhe re around the world.
VIP-155PT main page Current State Current state information Network Shows the W AN and LAN port conne cti ng state and current sett ings VOIP Part show the working st ate of V oIP , you can see whethe.
17 WAN Config: Three methods are available for Internet Access S tatic IP Fixed IP User If you are a leased line user with a fixed IP address, fill out the following items with the information provided by your ISP .
18 LAN Config Field Description Bridge Mode Enable this option to switch to bridge mode. IP phone won’t assign IP for it s LAN port in bridge mode and it s LAN and W AN port will be in the same network (This setting won’t take ef fect unless you save the config and reboot the device) IP address LAN IP addre ss of VIP-15 5PT Default: 192.
Setting page of public SIP server . Field Description Register Server Addr Register address of publi c SIP server Register Server Port Register port of public SIP server Registe r Username Username of.
DTMF Mode DTMF signal sending mod e: support RFC2833, DTMF_RELA Y (inband audio) and SIP info Server T ype It could support dif ferent SIP Proxy providers RFC Protocol Edition Current IP PHO NE SIP version. Set to RFC 2543 if the gate n eed to communicate to devices (such as CISCO5300 ) using the SIP 1.
Star t IP S t art IP of lease tabl e End IP End IP of lease t able. Network device connecting to the IP PHONE LAN port can dynamic obt ain the IP in the range between st art IP and end IP Netmask Netm.
Inside IP LAN device IP for port ma pping Inside Port LAN device port for port mapping Out side Por t W AN port fo r port mapping Click Add to add new port mapping item and Delete to delete current port mapping item. Net Service Field Description HTTP Port Configure HTTP transfer port, def ault is 80.
Firewall setting page. User may set up firewall to pr event unauth ori zed Internet users from accessing private networks connected to the Internet (input rule), or pr event unauthorized private network devices to access the internet. Access list support two type limit s: input_access limit or output_access limit.
Dest Addr destination address. Can be IP addre ss or network address Src Mask source address mask. Indi cate the s ource is dedicate IP if set to 255.255.255.255. Otherwi se is n etwork ID Des Mask Destination address mask. Indicate the source is dedicate IP if set to 255.
This page is use d to set the private sip server , stun server , and ba ck up sip server information . STUN Server setting: Field Description STUN Server Addr Configure stun server ad dress STUN Serve.
User can register t w o sip servers: Public sip server and private sip server .these two sip servers are independent from each other and running in the same time. For how to configure private sip serve r . Please refer to SIP_Config Digital Map Digit map is a set of rules to determine whe n the user has finished dialing.
27 server . VIP-155PT support followi ng digital map: Field Description End With “# ” Use # as the end of dialing Fixed Length When the length of the diali ng match, the call will be sent Timeout S pecify the timeout of the last dial digit.
User configure the value add service su ch as hot line, call forward, call transfer , 3-way conference call .etc in this page Field Description Hotline Configure hotline number .
29 Ban Outgoing Enable this to ban outgoing calls Enable Call T ransfer Check the Enable Call T ransfer . Unattended transfer: If A is the IP PHONE user , and B calls and talking with A through V oIP . A can press FWD button to hold the call with B, and then enter C’ s number .
Incoming Record Playing Play the message when recording User-Defined V oice Use customi zes greeting voice for answering machine Record local message: User may use local message to leav e message to other local users.
Field Description CODEC select the prefer CODEC; support ula w , alaw ,G729 a nd G7231 5.3/6.3 Signal St andard Signal st andard for dif ferent area Input V olume Handset in volume Output V olume Hand.
32 ----Make direct IP to IP call ----Place the call to dif ferent servers according the prefix. Y ou can click “Add” to add a new dial rule. Below is the det ail setting of the dial-rule: Field Description Phone Number The Number suit for this dial rule, can be set as full match or prefix match.
Field Description 2T rule If the call starts with 2, the first 2 will be deleted, and the rest number will be sent to private SIP server . 3T rule If the call starts with 3, the first 3 will be deleted, and the rest number with be sent to public SIP server .
FTP/TFTP Update Backup: Back up configure file to your FTP/TFTP server . * configure use .cfg extension. Auto up date: IP PHONE IP phone support FTP and TFTP auto upda te. The gateway will auto obtain the configure file from your update server if configured.
Configure file version was in the <<V OIP CONFIG FILE>> a nd <GL OBLE CONFIG MODULE> ConfFile V ersion Example: Gateway original version is: <<VOIP CONFIG FILE>>V ersion:1.00 00 <GLOBLE CONFIG MODULE> ConfFile V ersion ： 6 User may edit the configure file version to: <<VOIP CONFIG FILE>>V ersion:1.
36 Phone Book User may set contact s in this page, and the c onta cts will be saved in the memory . Then usi ng the Pbook, V ol+, V ol-,Menu/OK and Exit keys to choose y our friend in the contact s and then p ress # to call out. Syslog Config Field Description Enable Syslog Enable syslog function.
Reboot Reboot IP phone, som e setting needs to reboot to make it works. Please always save config before reboot, otherwise the setting w ill return to previous setting.
38 Chapter 4 Keyp ad Configurations Keyp ad Function User can configure IP PHONE through its keyp ad. List below is the keyp ad function Keyp ad Mode Function/Display Idle mode ---- show current time .
39 # Calling mode Use as e nd key of dialing or the dial number Hold Calling m ode Hold, det ail refer value add service FWD Calling mode T r ansfer , detail refer value add service Redial Calling mode Redial key Send Calling mode call key No.
40 DEL FastCall Three Call Call-Trans fer Call-Waiting Condition Transfer Num Transfer IP Call-Forwar d SIP Port End With # Switch Dial-Rule Fixed Length Length Public Reg Reg Status Private Reg Publi.
41 Set Default Switch Server-IP Other Setting Syslog Server-Port.
5 Chapter 5 T elnet Console Introduce Basic Structure User may use telnet command to access a nd man age IP phone. IP PHONE a dopt s tree structure for telnet. Every node cont ains its sub -nodes or local comma nd. User can type “help” or “?” whe never to see sub-nodes and all local co mmand under current node.
43 Global Command Global command is availab le unde r all nodes, IP PHONE sup port following commands: Command Function Example chinese Set to Chinese UI #chinese clear Clear telnet screen #clear engl.
44 delete firewall rule ---no entry –I/O xxx –index xxx Example : <config-accesslist>#no entry –I/O input –in dex 1 S h o w f i r e w a l l s e t t i n g s - - - s h o w [disable] enable.
45 Show LAN port IP address ---ipshow S h o w N A T i n f o - - - n a t s h o w Change LAN port IP address ---ip –addr x.x.x.x –mask x.x.x.x Example: <config-interface-fastet hernet-lan>#ip –a ddr 192.
46 Example: <config-nat>#tcp-entry –ip 192 . 168.1.5 –lanport 1720 –wanport 1000 Delete TCP mapping rule ---no entry –ip x.x.x.x –lanport xxx –wanport xxx Example: <config-nat>#n o tcp-e ntry –ip 192.168.1.5 –lanport 5060 –wa nport 1000 Add UDP mapping rule -- -udp-entry –ip x.
47 ---entry –number xxx –ip x.x.x.x –protocol xxx _add xxx Example: <config-pbook># entry –number 100 –ip 202.1 12. 20.100 –protocol sip _add 123(dial 100 an d will send 123100 accordin g this rule) Add number-IP bond and replace the destination with another number ---entry –number xxx –ip x.
48 Set prefer codec ---codec xxx Set DTMF gain ---dtmfvolume xxx Set black list ---in- limit xxx S h o w b l a c k l i s t - - - i n - l i m i t Set input volume ---input xxx Set outgoing limit list -.
49 Set local SIP signal port --- signalpor t xxx Set proxy server ---s erver proxy -ip x.x.x.x _port xxx _user xxx _password xxx Example: <config-sip-serve r># p roxy ip 2 10.25.23. 2 2 _port 5060 _user aaa _p a ssword 123456 Set register server info ---server register -ip x.
50 Download configure to flash usage: #download tf tp –ip x.x.x.x –file xxx #download ftp –user xxx –password xxx –ip x.x.x.x –file xxx Example: #download f tp –user abc –p assword 123 –ip 202.
51 path: <show># show debug info Example: #<show>#debug ging ¾ dhcp-server path: <show># show LAN st atus and DHCP se rver inf o Example: #<show># dhcp-server ¾ dial-rule pat.
52 Show ip packet s S tat. Example: #<show>#ip ip Show RTP packet s S tat. Example: #<show>#ip rtp Show TCP packet s S t at. Example: #<show>#ip tcp Show UDP p ackets S tat.
53 show current phone number Example: #<show>#port number show current port st atus Example: #<show>#port st atus ¾ PPPoE path: <show># show PPPoE info Example: #<show># pp po.
54 Password:xxx # #logout Telnet and logout path: <time># ---manualset –year xxx –month xxx –day xxx –hour xxx –minute xxx –second xxx Example: <time>#manulset –year 2004 –month 10 – day 1 –hou r 8 –minitute 30 –second 0 [disable]enable SNTP server ---sntp [no] start Set SNTP IP address ---sntp server x.
ping Check if the destination is accessible #ping www .google.com tracert Show network path info #tracert www .googl e.com show basic Show network setting s #show basic show ip route Show route table .
56 Appendix A FA Q Q1: How many servers may VIP-15 5PT r egister simultaneously? A1: VIP-155PT is able to register two SIP serv ers simult ane ously , and redundancy servers.
Appendix B V oice communications There are several ways to make call s to desired dest ination in IP Phone. In this section, we’ll lead you step by step to esta blish your first voice communi cation via keypad and web browsers opera tions. Peer to Peer (P2P) Mode Step 1: A ssuming there are two VIP-155PT in the network the IP address are 172.
Step 4: Pi ck up handset or press “Handfree” key fro m keypad of VIP-155PT -A and dial “2#”. Then the phone of VIP-155PT -B should ring. Y ou can do the same thing to the VIP-155PT -B.
Please browse machine “ Vo I P ” Æ “ SIP Config ” menu, and enable the “ Enable Register ” check box. Insert IP address of t he remote calling p arty in the “ Register Server Addr ” field. Sample configuration screen is shown below: After these configuration s, be sure to cli ck the “ Apply ” button to apply settings.
SETP 3: Browsing to “ Config Manage ” Æ “ Sav e Config ” configuration item and press “ Sav e ” button to save the configuration. Browsing to “ System Manage ” Æ “ Reboot ” menu and press “ Reboot ” button reb oot the machine to make the se ttings ef fective.
61 Appendix C VIP-155PT series Specifications Product Power over Ethernet SIP IP Phone Model VIP-155PT Hardware WAN 1 x 10/100Mbps RJ-45 port Power Over Ethernet 802.3af compliant at PT model LAN 1 x 10/100Mbps RJ-45 port LCD display 2 x 1 6 charact ers Speaker 8 Ohm/0.
Een belangrijk punt na aankoop van elk apparaat Planet Technology VIP-155PT (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Planet Technology VIP-155PT heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Planet Technology VIP-155PT vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Planet Technology VIP-155PT leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Planet Technology VIP-155PT krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Planet Technology VIP-155PT bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Planet Technology VIP-155PT kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Planet Technology VIP-155PT . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
