Gebruiksaanwijzing /service van het product 28-306 van de fabrikant Porter-Cable
Ga naar pagina of 20
14" Metal/W ood Cutting Band Saw Shown with Optional Stand and Optional Mobile Base Model 28-306 INSTRUCTION MANUAL P ART NO. 426-03-651-0011 - 06-03-03 Copyright © 2003 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .
2 W oodworking can be dangerous if safe and pr oper operating procedur es are not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the product. Using the machine with r espect and caution will con- siderably lessen the possibility of personal injury .
3 1. FOR YOUR OWN SAFETY , READ THE INSTRUCT - TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly mini- mize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT .
4 ADDITIONAL SAFETY RULES FOR BAND SA WS 1. DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instruc- tions. 2. OBT AIN ADVICE from your supervisor, instruc- tor , or another qualified person if you are not familiar with the operation of this tool.
5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be pr o - tected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wir e extension cords which have 3-pr ong ground- ing type plugs and matching receptacle which will accept the machine’ s plug.
6 Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cor d which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
7 ASSEMBL Y OPTIONAL ST AND The optional stand is shipped top-down in the shipping container with the motor mounted to the inside top of the stand. The on/off switch is wir ed to the end of the power cord. T o make the motor operational, do the following: 1.
8 A TT ACHING BEL T AND PULLEY GUARD, A TT ACHING AND ALIGNING V -BEL T , ADJUSTING BEL T TENSION DISCONNECT MACHINE FROM POWER SOURCE. 1. Use a straight edge to align the inside grooves of the pulleys (A) and (B) Fig. 9 to the inside edge of the drive pulley (C).
9 A TT ACHING THE SWITCH A push-button switch (mounted in a switch box) and a cord set ar e supplied with the unit. T o attach the switch to the band saw arm: DISCONNECT MACHINE FROM POWER SOURCE. The on/off switch-to-motor cor d (F) Fig. 11 is tied to the vertical mounting post (G) opposite the motor pulley .
10 Fig. 19 T ABLE INSER T Place the table insert (A) Fig. 19 in the hole provided in the table. Engage the protrusion on the insert in the indent (B) in the table. TIL TING THE T ABLE 1. The table on the machine can be tilted 45 degrees to the right and 10 degr ees to the left.
11 ADJUSTING BLADE TENSION A series of graduations is located on the back of the upper wheel slide bracket. These graduations indicate the proper tension for various widths of blades. With the blade on the wheels, turn the knob (A) Fig. 23 to raise or lower the wheel, until the re d fiber washer (D) Fig.
12 Fig. 30 Fig. 31 When using the machine for wood cutting (3000 SFM), pull the shifter knob (A) Fig. 30 all the way out so that the lugs of the clutch (B) are engaged with the hub (C) of the drive pulley . This action will disengage the clutch (D) from the hub (E) of the gear that transmits power through the gear box.
13 BEL T AND PULLEY ARRANGEMENTS FOR ALL EIGHT A V AILABLE SPEEDS With the longest belt on the inside groove of the motor pulley (B) Fig. 32 and on the drive pulley (C), and the small belt in one of t.
14 T rouble: BAND SA W DOES NOT COME UP TO SPEED. Pr obable Cause Remedy 1. Low voltage due to improper extension cord size. 1. Replace with adequate size cord. 2. Low voltage. 2. Contact an electrician. T rouble: BLADES BREAK. Pr obable Cause Remedy 1.
15 CUTTING CURVES When cutting curves, turn the stock carefully so that the blade may follow without being twisted. If a curve is so abrupt that repeated new kerfs ar e needed, then use either a narrower blade or one that has mor e set. The more set a blade has, the easier the stock is to turn.
16 BAND SAW BLADES A band saw blade is a delicate piece of steel that is subjected to tremendous strain. Y ou can obtain long use from a band saw blade if you use it properly . Be sure you use blades of the proper thickness, width, and temper for the various types of material and cuts.
17 LUBRICA TION The gear case is filled at the factory with 1-1/2 quarts of oil. The case should be drained after 1500 to 2000 hours of operation and filled with a good grade of heavy adhe- sive gear oil. A pipe plug is located underneath the machine in line with the gear pulley .
18 P ARTS, SERVICE OR W ARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations.
19 T wo Y ear Limited New Pr oduct W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven t.
20 The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): Auto-Set ® , BAM- MER ® , B.
Een belangrijk punt na aankoop van elk apparaat Porter-Cable 28-306 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Porter-Cable 28-306 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Porter-Cable 28-306 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Porter-Cable 28-306 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Porter-Cable 28-306 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Porter-Cable 28-306 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Porter-Cable 28-306 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Porter-Cable 28-306 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
