Gebruiksaanwijzing /service van het product 5600 van de fabrikant POSIFLEX Business Machines
Ga naar pagina of 20
Part 1 FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications.
Part 2 ALERT TO OUR HONORABLE CUSTOMERS: l Please always read thoroughly all the instructions and documents delivered with the product before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences.
Part 3 BRIEF INTRODUCTION The User ’ s Manual The purpose of this manual is to guide the user in the initial installation and general use of the Posiflex Jiva TP/LT - 5600 series and Jiva TP/LT - 5800 series of POS terminals. It does not explain any application software that may be suppl ied with it.
Part 4 i) L ong life touch panel that endures 10 million touches at sa me spot (for Jiva TP only) j) Spill proof water resistant structure allowing easy cleaning k) Easy maintenance construction l) Various I/O ports supported, including: 1. one PS/2 KB port 2.
Part 5 MSR or smart card reader and finger print sensor o r iButton reader ² Security upgrade kit SD200 covering options of USB interface MSR or optical scan type finger reader ² Bar code card reade.
Part 6 INSTALLATION GUIDES CAUTION: Before any installation or cable connection to the set, please always make certain that the system is turned o ff and the external power source to the set is remove.
Part 7 DISCONNECTING CABLES After removal of the cable cover, the connector area will be accessible then. Please disconnect every cable before separation of main unit and the adjustable stand assembly.
Part 8 and take the cable passage cover away to show the cable passa ge. If there is no need to install the optional UPS battery here, please skip the next paragraph and start routing cables through the cable passage. Otherwise, please remove the four screws holding the battery cover to install the battery.
Part 9 ROUTING THE CABLES Place all the cables required for connections to the Jiva TP/LT - 56 00 or Jiva TP/LT - 5800 except those for special application purposes into the cable passage. Insert one end of the cable passage cover under the adjacent cover plate and screw on the two screws.
Part 10 INSTALLING UPGRADE KIT Please follow the instructions in the manuals delivered with the side mount upgrade kit: KP100, SD100 , SD200 or BC100 U and the rear top mount upgrade kit PD302 to fit them in Jiva 5600 / Jiva 5800 construction.
Part 11 JOINING MAIN UNIT AND STAND Match the matching pegs on the back of the main unit against the matching holes on the stand. First aim the matching pegs toward the upper round part of the hole and make sure that all pegs are inside the holes. Then slide the main unit down to move the pegs into the lower slot part of the holes till it clicks.
Part 12 assembly. The stand assembly is not engaged in wall mount operation. LOCATION FOR INSTALLATI ON As the stand assembly is not involved in wall mount installation, the space required for wall mount application will take only the main unit into consideration.
Part 13 For Jiva TP/LT - 5800 , the operating system exists in the HDD. Once the software system on HDD collapses, it is possible to restore t he operating system onto a physically intact HDD with use of the Recovery CD that comes with the preloaded operating system.
Part 14 USING THE TOUCH POS APPLICATION ENVIRONMENT It is very important that you check the following operation guidelines: Ventilation This terminal must NOT be operated in an environment with r estricted ventilation. The installation should be such that there is at least 25mm air clearance around any top or side ventilation holes.
Part 15 Emergency treatment: The battery is constructed maintenance free and leakproof. It is well protected in Jiva system as long as the ambient temperature remains below 30 ° C and the ventilation of the Jiva system remains free.
Part 16 Hardware Power Switch The power switc h located at left side of the main unit is a slide type switch. This switch controls the power on/off of the system. This switch turns the system on when slid downward, only when external power is present.
Part 17 3. Alarm setup detail will appear. Set the alarm as wished then press “ F10 ” key to save and exit CMOS setup. 4. This system may be powered off and will automatically boot up at the preset alarm time.
Part 18 VGA cable or purchase another type of VGA cable and set an internal jumper in Jiva TP/LT - 56 00 or Jiva TP/LT - 5800 to supply the required power through the VGA connector. Do not connect other m onitor to this port before the power in this port is disabled.
Part 19 a matter of few seconds that the system will automatically shutdown power due to uprising temperature. Please review the ventilation condition and environment temperature, check if the fan is stuck by contaminants such as dry grease or threads and try to correct the situation when th e system is off and cooled down.
Part 20 RS232 Touch Controller If the J iva TP - 56 00 or Jiva TP - 58 00 purchased is the leading edge Infra Red type touch models, the touch controller is of RS232 interface. The “ Posiflex Touch Terminal Manager” above should be disregarded. In these models, the COM4 position of the system will be c overed in the connection area.
Een belangrijk punt na aankoop van elk apparaat POSIFLEX Business Machines 5600 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen POSIFLEX Business Machines 5600 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens POSIFLEX Business Machines 5600 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding POSIFLEX Business Machines 5600 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over POSIFLEX Business Machines 5600 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van POSIFLEX Business Machines 5600 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de POSIFLEX Business Machines 5600 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met POSIFLEX Business Machines 5600 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
