Gebruiksaanwijzing /service van het product 180196 van de fabrikant Poulan
Ga naar pagina of 48
02478 OWNER'S MANUAL MODEL: PR17542ST A LA WN TRACT OR Always W ear Eye Protection During Operation WARNING: Read the Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. IMPOR T ANT MANUAL Do Not Thr ow A way 180196 Rev.
2 I. GENERAL OPERATION • Read, understand, and follow all instructions in the manual and on the machine before starting. • Only allow responsible adults, who are familiar with the instructions, to operate the machine. • Clear the area of objects such as rocks, toys, wire, etc.
3 T ABLE OF CONTENTS SAFETY RULES ........................................................ 2 - 3 PRODUCT SPECIFICATIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ...................... 4, 14 - 17 ASSEMBLY ....................
4 CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center/department.
5 (1) Large Flat Washer (1) Locknut 5/16-18 (1) Hex Bolt 5/16-18 x 1-1/4 (1) Hex Bolt 3/8-16 x 1 (1) Lock washer 3/8 Steering Wheel Insert Steering Extension Shaft Steering Sleeve Steering Wheel Steer.
6 ASSEMBL Y TOOLS REQUIRED FOR ASSEMBL Y A socket wrench set will make assembly easier. Standard wrench sizes are listed. (2) 1/2" wrenches Utility knife (1) 9/16" wrench Tire pressure gauge Pliers When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).
7 ASSEMBL Y FIG. 2 TO ROLL TRACTOR OFF SKID (See Opera- tion section, page 10, for location and function of controls) • Press lift lever plunger and raise attachment lift lever to its highest position. • Release parking brake by depressing clutch/brake pedal.
8 ASSEMBL Y CHECKLIST BEFORE YOU OPERATE AND ENJOY YOUR NEW TRAC- TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed.
9 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR WARNING REVERSE FORWARD FAST SLOW ENGINE ON ENG.
10 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
11 OPERA TION STOPPING (See Fig. 6) MOWER BLADES - • To stop mower blades,move attachment clutch lever to “DISENGAGED” position. GROUND DRIVE - • To stop ground drive, depress clutch/brake pedal into full “BRAKE” position. • Move gear shift lever to neutral (N) position.
12 OPERA TION ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION ATTACHMENT LIFT LEVER HIGH POSITION "ENGAGED" POSITION LOW POSITION FIG. 7 DEFLECTOR SHIELD TO OPERATE ON HILLS 3/8 WASHER 3/8-16 LOCKNUT GAUGE WHEEL MOUNTING BRACKET SHOULDER BOLT GAUGE WHEEL FIG.
13 OPERA TION MOWING TIPS • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has been cut.
14 CUST OMER RESPONSIBILITIES BEFO R E EACH USE T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Fi.
15 CUST OMER RESPONSIBILITIES TRACTOR Always observe safety rules when performing any mainte- nance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).
16 CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. CUST OMER RESPONSIBILITIES V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary.
17 CUST OMER RESPONSIBILITIES MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
18 SER VICE AND ADJUSTMENTS CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift lever in neutral (N) position. • Place attachment clutch in “DISENGAGED” position.
19 SER VICE AND ADJUSTMENTS NUT "E" TRUNNION "D" "D" MANDREL FIG. 18 NUT "F" FRONT LINKS FIG. 19 FRONT-TO-BACK ADJUSTMENT (See Figs.
20 TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 23) The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows: • Make sure transaxle is in neutral (N).
21 SER VICE AND ADJUSTMENTS FIG. 24 RETAINING RING WASHERS SQUARE KEY (REAR WHEEL ONLY) AXLE COVER TO REMOVE WHEEL FOR REPAIRS (See Fig. 24) • Block up axle securely. • Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).
22 SER VICE AND ADJUSTMENTS TO REPLACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood.
23 SER VICE AND ADJUSTMENTS FIG. 30 FIG. 29 CLAMP SCREW SWIVEL CLAMP SCREW STOP ENGINE TO ADJUST THROTTLE CONTROL CABLE (See Fig. 29) The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable.
24 ST ORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
25 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
26 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine continues to run 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves corrected, contact an authorized service center/ seat with attachment department.
27 TRACTOR - - MODEL NUMBER PR17542ST A SCHEMA TIC BATTERY FUSE IGNITION SWITCH RED RED RED BLACK IGNITION UNIT HEADLIGHTS REMOVABLE CONNECTIONS BLACK BLACK BLACK WHITE WHITE WHITE RED BLACK ORANGE BL.
28 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR17542ST A ELECTRICAL 28 29 26 24 42 43 27 27 25 41 27 27 40 33 90 30 8 2 1 27 D . C . A M P E R E S 45 16 22 21 52 16.
29 KEY P ART N O . N O . DESCRIPTION 1 144927 Battery 12 Volt 35 Amp 2 74760412 B ol t Hex Hd 1/4-20unc X 3/4 8 176689 Battery Box 1 6 176138 S w i tch Interlock Push-In 2 1 175685 H arness Socket Lig.
30 26 25 58 219 20 219 23 64 208 13 208 11 1 3 2 9 208 208 5 5 207 3 3 3 142 17 29 28 12 51 57 53 52 54 55 145 37 3 37 24 26 25 3 31 24 30 35 3 26 33 10 26 34 35 18 14 38 14 206 212 159 3 115 3 142 21.
31 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR17542ST A CHASSIS AND ENCLOSURES KEY P ART N O . N O . DESCRIPTION 1 174619 C hassis 2 176554 Drawbar 3 17060612 Screw 3/8-16x.
32 29 28 112 14 41 38 39 57 51 74 75 78 76 77 1 25 19 24 2 53 35 34 37 36 35 62 36 59 212 55 77 61 22 27 26 6 113 18 51 5 18 6 85 52 30 32 32 30 52 11 85 80 4 3 13 81 84 82 64 65 145 79 16 96 26 27 51.
33 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR17542ST A DRIVE KEY P ART N O . N O . DESCRIPTION KE Y PART NO. N O. DESCRIPTION 1 - - - - - - Transaxle Peerless (206-545C) (Order parts from transaxle ma.
34 5 5 4 3 43 6 43 8 10 40 32 11 8 6 87 46 46 8 6 87 29 88 71 17 43 91 2 1 41 42 37 36 37 38 39 44 51 54 33 35 34 68 67 67 67 13 65 68 15 15 15 29 29 82 63 11 REP AIR P ARTS TRACTOR - - MODEL NUMBER P.
35 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR17542ST A STEERING ASSEMBL Y KEY P AR T N O . N O . DESCRIPTION 1 180656 W heel Steering 2 172393 A x l e A s m Cast Iron LT 3 169840 S pindle Asm LH 4 169.
36 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR17542ST A SEA T ASSEMBL Y 1 171683 Seat 2 140551 Bracket Pivot Seat 8 720 3 71110616 B o l t F i n Hex 3/8-16 Unc X 1 4 19131610 W asher 13/32 X 1 X 10 Ga 5 145006 C lip Push-In 6 73800600 N u t H e x w / I n s .
37 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR17542ST A DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART N O . N O . DESCRIPTION 6 2 1 5,8 4,10 3,9 11 7 WHEELS AND TIRES KEY P ART N O . N O . DESCRIPTION KEY P ART N O .
38 2 1 OPTIONAL EQUIPMENT Spark Arrester 29 10 11 6 5 12 13 26 25 17 3 16 17 81 44 46 32 31 33 37 33 4 8 23 45 41 112 40 14 38 15 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR17542ST A ENGINE.
39 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR17542ST A ENGINE 1 170771 Control Th/ch Flag 2 17720408 S c r e w Hex Thd Cut 1/4-20x5/8 T 3 - - - - - - - - Engine, Briggs Model 407777 (Order Parts From .
40 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR17542ST A MOWER DECK 15 14 13 11 10 9 8 16 68 37 30 31 32 33 146 148 145 150 45 144 147 147 142 149 142 49 50 51 54 52 53 55 56 34 1 46 44 21 22 24 25 26 2.
41 KEY P ART N O . N O . DESCRIPTION KEY P ART N O . N O . DESCRIPTION 1 165892X421 M o w e r D eck Assembly, 42" 2 72140506 B o l t 3 138017 Bracket Asm Fr.
42 36 15 20 16 17 18 20 20 15 20 4 5 6 2 3 1 6 5 4 7 8 23 24 25 27 28 29 30 37 41 40 38 12 11 31 32 31 32 19 19 13 13 13 13 49 26 50 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR17542ST A MOWER LIFT.
43 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR17542ST A MOWER LIFT 1 159460 W i r e Asm Inner/Sprg W/plunger LT 2 159471 Shaft Asm Lift RH w/Inf 3 105767X P i n G roove 1 500 Zinc 4 12000002 E R i n g .
44 NOTES.
45 LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship.
46 T E C U M S E H ® Issued January 1980 Revised January 1991 T E C U M S E H ® POLICY LIMITED WARRANTIES FOR NEW PEERLESS GEAR POWER TRAIN COMPONENTS A.
47 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
Your POULAN PRO product has been expertly engineered and carefully manufactured to rigid quality standards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. FOR SERVICE OR REPLACEMENT PARTS: 1.
Een belangrijk punt na aankoop van elk apparaat Poulan 180196 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Poulan 180196 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Poulan 180196 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Poulan 180196 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Poulan 180196 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Poulan 180196 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Poulan 180196 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Poulan 180196 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
