Gebruiksaanwijzing /service van het product PRGT22H50B van de fabrikant Poulan
Ga naar pagina of 52
177937 Rev. 4 06.28.01 RH Printed in U.S.A. OWNER'S MANUAL MODEL: PRGT22H50B LA WN TRACTOR Always Wear Eye Protection During Operation W ARNING: Read the Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury.
2 I. GENERAL OPERATION • Read, understand, and follow all instructions in the manual and on the machine before starting. • Only allow responsible adults, who are familiar with the instructions, to operate the machine. • Clear the area of objects such as rocks, toys, wire, etc.
3 Safe Operation Practices for Ride-On Mowers SAFETY RULES • Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off. • Do not mow in reverse unless absolutely necessary.
4 PRODUCT SPECIFICA TIONS GASOLINE CAPACITY 3.5 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF-SJ): SAE 30 (above 32 ° F) SAE 5W-30 (below 32 ° F) OIL CAPACITY: W/ FILTER: 4.0 PINTS W/O FILTER: 3.75 PINTS SPARK PLUG: CHAMPION RC12YC (GAP: .040") GROUND SPEED (MPH): FORWARD: 0 – 5.
5 UNASSEMBLED P ARTS Steering Wheel (1) Knob (1) Washer 17/32 x 1-3/16 x 12 Gauge Seat (2) Keys Slope Sheet Keys Steering Wheel Inser t Mower (2) F ront Link Assemblies Gauge Wheel (4) Retainer Springs (single loop) (3) Retainer Springs (double loop) (2) Hex Bolts 5/16-18 x 1 (2) Washers 17/32 x 7/8 x 16 Ga.
6 ASSEMBL Y Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
7 ASSEMBL Y TO ROLL TRACTOR OFF SKID (See Opera- tion section for location and function of con- trols) • Press lift lever plunger and raise attachment lift lever to its highest position.
8 ASSEMBL Y NOSE ROLLER “ A ” BRACKET TAB WASHER TAB HOLE LOCK NUT “ B ” BRACKET TAB FIG. 5 HEX BOLT TO ATTACH NOSE ROLLER (See Fig. 5) • Position brackets, 17/32 x 7/8 x 16 gauge washers, and nose roller between deck mounting brackets as shown.
9 ASSEMBL Y CHECKLIST BEFORE YOU OPERATE AND ENJOY YOUR NEW TRAC- TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed.
10 These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR WARNING REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF OI.
11 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR. Compare the illustrations with your tractor to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
12 OPERA TION FIG. 8 MOWER BLADES - • To stop mower blades,move attachment clutch switch to “ DISENGAGED ” position. GROUND DRIVE - • To stop ground drive, depress brake pedal into full “ BRAKE ” position. IMPORTANT: THE MOTION CONTROL LEVER RETURNS TO NEUTRAL (N) POSITION WHEN THE BRAKE PEDAL IS FULLY DEPRESSED.
13 OPERA TION TO OPERATE MOWER (See Figs. 7 and 10) Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. • Select desired height of cut.
14 OPERA TION ADD GASOLINE • Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.
15 OPERA TION FIG. 12 PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is running. To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time.
16 B E F O R E E A C H U S E T R A C T 0 R Adjust Motion Drive Belt(s) Tension Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil Replace Air Fil.
17 CUST OMER RESPONSIBILITIES TRACT OR Always observe safety rules when performing any mainte- nance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “ TO ADJUST BRAKE ” in the Service and Adjustments section of this manual).
18 CUST OMER RESPONSIBILITIES TRANSAXLE COOLING The fan and cooling fins of transmission should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, no not use high pressure water or steam to clean transaxle.
19 CUST OMER RESPONSIBILITIES MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
20 SER VICE AND ADJUSTMENTS CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “ DISENGAGED ” position. • Turn ignition key “ OFF ” and remove key. • Make sure the blades and all moving parts have completely stopped.
21 SER VICE AND ADJUSTMENTS FIG. 23 FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22) IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.
22 SER VICE AND ADJUSTMENTS TO ADJUST ATTACHMENT CLUTCH (See Fig. 25) The electric clutch should provide years of service. The clutch has a built-in brake that stops the pulley within 5 seconds. Eventually, the internal brake will wear which may cause the mower blades to not engage, or, to not stop as required.
23 SER VICE AND ADJUSTMENTS TRANSMISSION REMOVAL/REPLACEMENT Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “ PURGE TRANSMIS- SION ” in the Operation section of this manual.
24 FIG. 31 L.H. PANEL BOLT “ POSITIVE ” (+) “ NEGATIVE ” (-) TO START ENGINE WITH A WEAK BATTERY (See Fig. 31) CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.
25 TERMINAL GUARD TERMINAL ACCESS DOOR FIG. 32 TO REPLACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
26 SER VICE AND ADJUSTMENTS CLAMP SCREW FIG. 36 FIG. 35 SWIVEL CLAMP SCREW STOP ENGINE TO ADJUST THROTTLE CONTROL CABLE (See Fig. 35) The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable.
27 ST ORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
28 Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “ CHOKED ” properly. 2. See “ TO START ENGINE ” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug.
29 PRO BLE M CAUSE CORRECTION Engine continues to run 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an authorized service center/ with attachment clutch department.
30 SER VICE NOTES.
31 TRACTOR - - MODEL NUMBER PRGT22H50B SCHEMA TIC BATTERY FUSE RED RED BLACK BLACK BLACK BLACK BLACK BLACK BLACK BLACK BLACK NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS BLACK BLACK BROWN RED ORANG.
32 30 33 24 42 43 40 26 28 25 50 29 27 27 41 16 12 12 11 10 8 2 1 27 D .C . A M P E R E S 45 81 52 22 21 79 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B ELECTRICAL.
33 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B ELECTRICAL 1 144926 B a t t e ry 2 74760412 Bo l t Hex Head 1/4-20 x 3/4 8 7603J Tray, Battery 1 0 145211 B o l t B t r F r t 1 / 4-20 X 7.
34 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B CHASSIS AND ENCLOSURES 31 68 43 34 20 21 84 47 24 39 17 86 4 2 19 20 16 17 56 21 47 17 28 91 1 36 36 50 42 17 17 17 21 21 44 23 17 8 68 156 156 15.
35 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B CHASSIS AND ENCLOSURES 1 175465 R ail, Frame RH 2 175282 D r awbar, Gt 4 73680700 N u t, C ro w nl ock 7/16-14Unc 5 163976X428 Dash 6 157882 D ash Asm., Lower 7 17720408 S crew, Thd Cut 1/4-20 x 1/2 8 145166 Support, Battery 1 4 175259X428 Hood Asm.
36 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B GROUND DRIVE 9 7 55 53 65 130 131 34 35 37 38 40 41 42 68 46 36 37 38 64 39 56 29 89 132 77 70 71 74 89 148 89 133 120 98 112 22 94 94 126 138 23 .
37 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B GROUND DRIVE KEY P AR T N O . N O . DESCRIPTION KEY P AR T N O . N O . DESCRIPTION 1 - - - - - - - Transaxle Hydro Gear 331-3000 (Order Parts From Transaxle Manufacturer) 2 9396E Key Sq.
38 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B STEERING ASSEMBL Y 47 48 46 49 50 8 6 29 28 23 31 41 22 21 20 44 1 45 14 25 34 33 32 6 27 42 27 6 19 15 14 35 18 16 9 8 7 2 6 6 4 14 15 14 14 15 1.
39 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B STEERING ASSEMBLY 1 159944X428 W heel, Steering 2 137094 A xl e A s m . , F ront 3 6855M F itting, Grease 4 161849 S pindle Asm, LH 5 161848 S pi nd le As m. , R H 6 6266H Bearing, Race Thrust Harden 7 121748X W asher 25/32 x 1-5/8 x 16 Ga.
40 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B ENGINE 1 84 24 12 11 41 42 43 10 9 8 40 29 SPARK ARRESTER KIT 84 45 47 39 18 15 17 37 28 37 27 26 16 22 25 21 20 74 62 71 70 79 69 83 35 2 81 82 3.
41 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B ENGINE KEY P AR T N O . N O . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 - - - - - - - Engine Briggs, Model No. 407777 (Order parts from engine manuf.) 2 149723 M u ffler Side 8 121361X P ulley V-Idler 9 177748 Keeper Asm.
42 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B SEAT ASSEMBLY 1 173818 S e a t 2 140551 B r acket, Pivot Seat 3 140675 S t ra p, Fender Asm. 4 127018X B o lt, Shoulder 5/16-18 x .62 5 145006 C l ip , Push-In Hinged 6 73800600 N u t, C ro w nl ock 3/8-16 7 124181X Spring, Seat Cprsn.
43 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B LIFT ASSEMBLY KEY P AR T N O . N O . DESCRIPTION KEY P AR T N O . N O . DESCRIPTION 1 121006X R o d A s m . , Lever 2 159187 Shaft Asm., Lift Vgt 3 159189 Lever Asm., Lift Rh 4 12000022 E - R i n g T r u ar c #5133-87 5 19292016 W asher 29/32 x 1-1/4 x 16 Ga.
44 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B MOWER DECK 55 46 27 39 45 44 43 45 44 51 45 56 48 48 45 53 52 38 50 48 49 63 47 45 27 28 27 31 30 30 32 33 45 27 31 40 32 66 37 33 65 5 6 6 7 54 3.
45 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B MOWER DECK KEY P AR T N O . N O . DESCRIPTION KEY P AR T N O . N O . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 156990X421 Deck Weldment 50" 2 73680500 N ut, Crownlock 5/16-18 5 138457 Bracket Asm.
46 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT22H50B DECALS 23 1 3 9 14 4 23 10 19 6 16 17 11 KEY P A RT N O . N O . DESCRIPTION KEY P AR T N O . N O .
47 SER VICE NOTES.
48 SER VICE NOTES.
49 SER VICE NOTES.
50 LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship.
51 15 MAX. SIGHT AND HOLD THIS LEVEL WITH SKY LINE OR TREE. C U T O U T O N D O T T E D L IN E S T H IS IS A 1 5 S L O P E SIGHTING GUIDE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION Operate your Tractor up and down the face of slopes (not greater than 15 ), never across the face.
Y o u r POULAN PRO product has been expertly engineered and carefully manufactured to rigid quality standards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. FOR SERVICE OR REPLACEMENT PARTS: 1.
Een belangrijk punt na aankoop van elk apparaat Poulan PRGT22H50B (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Poulan PRGT22H50B heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Poulan PRGT22H50B vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Poulan PRGT22H50B leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Poulan PRGT22H50B krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Poulan PRGT22H50B bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Poulan PRGT22H50B kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Poulan PRGT22H50B . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
