Gebruiksaanwijzing /service van het product 188904 van de fabrikant Poulan Pro
Ga naar pagina of 28
OWNER'S MANUAL MODEL: PRR T65D REAR TINE TILLER AL W A YS WEAR EYE PROTECTION DURING OPERA TION 188904 11.25.03 TR Printed in U. S.A. W ARNING: Read this Owner's Manual and fol low all W arnings and Safety In struc tions. Failure to do so can result in serious injury .
2 • Ne v er operate the tiller without proper guards , plates, or other saf ety protectiv e de vices in place. • K eep children and pets a wa y . • Do not ov erload the machine capacity by attempting to till too deep at too f ast a rate . • Nev er operate the machine at high speeds on slippery surf aces.
3 CONGRA TULA TIONS on y our purchase of a new tiller . It has been designed, en gi neered and manu fac tured to give you the best pos sible de penda bil ity and per fo r m ance. Should you e xper ience any prob lems y ou can not easily remedy , please contact your nearest authorized service center .
4 T OOLS REQUIRED FOR ASSEMBL Y A sock et wrench set will mak e assemb ly easier . Standard wrench sizes are listed. (1) Utility knif e (1) Tire pressure gauge (1) P air of pliers (1) 9/16" wrench OPERA T OR’S POSITION (See Fig.
5 ASSEMBL Y • Grasp handle assembly . Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. HANDLE ASSEMBL Y "UP" POSITION FIG. 4 UNP A CKING CAR T ON (See Fig. 2) CA UTION: Be careful of e xposed sta ples when handling or disposing of cartoning material.
6 ASSEMBL Y SHIFT ROD HAIRPIN CLIP SHIFT LEVER INDICA T OR REMO VE TILLER FROM CRA TE • Make sure shift le v er indicator is in “N” position (See Fig. 7) • Tilt tiller f orward by lifting handle . Separate cardboard cov er from le veling shield.
7 KNO W Y OUR TILLER READ THIS O WNER'S MANU AL AND SAFETY R ULES BEFORE OPERA TING Y OUR TILLER. Compare the illustrations with y our tiller to f amiliarize y ourself with the location of v arious controls and adjustments. Sav e this manual f or future ref erence.
8 TURNING • Release the drive control bar . • Mov e throttle control to “SLOW” position. • Place shift le ver indicator in “F” (forw ard) position.
9 OPERA TION OIL LEVEL FIG. 12 BEFORE ST AR T ING ENGINE IMPORT ANT : BE VER Y CAREFUL NO T T O ALLO W DIR T T O ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN APPRO VED , CLEAN, CO VERED CONT AINERS. USE CLEAN FILL FUNNELS.
10 RUN CHOKE OPERA TION • Soil conditions are impor tant for proper tilling. Tines will not readily penetrate dry , hard soil which may con tr ib ute to e xcessiv e bounce and diffi cult handling of your tiller . Hard soil should be mois tened bef ore tilling; howe ver , e xtremely wet soil will “ball-up” or clump during tilling.
11 MAINTENANCE GENERAL RECOMMEND A TIONS The warranty on this tiller does not co v er items that ha v e been subjected to operator ab use or negligence. T o receive full v alue from the warranty , the operator must main tain tiller as instructed in this manual.
12 MAINTENANCE OIL FILLER PLUG OIL LEVEL OIL DRAIN PLUG FIG. 16 Disconnect spark plug wire before perf orming an y maintenance (except car bu re tor adjustment) to prevent accidental start ing of engine . Prevent fi res! Keep the engine free of grass, leaves, spilled oil, or fuel.
13 MAINTENANCE e ngine_ar t _ 61 FIG. 19 AIR SCREEN BLO W ER HOUS ING MUFFLER Do not operate tiller without muffl er . Do not tamper with e xhaust system. Damaged muffl ers or spark arresters could create a fi re hazard. Inspect pe ri odi cally and re place if nec es sar y .
14 SER VICE AND ADJUSTMENTS CA UTION: Disconnect spark plug wire fr om spark plug and place wire where it cannot come into contact with plug. TILLER T O ADJUST HANDLE HEIGHT (See Fig. 20) Select handle height best suited f or your tilling conditions .
15 SER VICE AND ADJUSTMENTS CABLE CLIP SCREW DRIVE CONTROL CABLE EXTENSION SPRING ENGINE PULLEY IDLER PULLEY TRANS MIS SION PULLEY LESS TEN SION 5/8" MORE TEN SION FIG. 23 T O REPLA CE GROUND DRIVE BEL T (See Figs. 22 and 23) • Remo v e belt guard as described in “T O REMO VE BEL T GU ARD”.
16 SER VICE AND ADJUSTMENTS tine_13 FIG. 26 TINE REPLA CEMENT (See Figs. 24, 25, and 26) CA UTION: Tines are sharp. Wear gloves or other pr otection when han- dling tines.
17 SER VICE AND ADJUSTMENTS FIG. 27 engine_art_78 THRO TTLE CONTROL CLAMP SCREW CASING AND WIRE ENGINE T O ADJUST THR O TTLE CONTROL CABLE (See Fig. 27) The throttle control has been preset at the f actory and ad just ment should not be necessar y .
18 ST ORA GE ENGINE OIL Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). CYLINDER(S) • Remov e spark plug. • P our 1 ounce (29 ml) of oil through spark plug hole into cylinder .
19 Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “T O ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se v eral min utes before attempting to start. 4. Dir ty air cleaner . 4. Clean or replace air cleaner car tridge.
20 REP AIR P ARTS TILLER - - MODEL NUMBER PRR T65D HANDLE ASSEMBL Y KEY P ART NO . NO . DESCRIPTION 21 180517X428 Handle 23 86777 Screw , He x Washer Hd.
21 KEY P ART NO . NO . DESCRIPTION 1 73510500 Nut, K eps 5/16-18 2 10040600 W asher , Lock 3/8 3 73220600 Nut, Hex 3/8-16 4 170127 Shield, Inner Belt Guard RT 5 164329 Screw , Shift Le v er 6 110111X Le v er , Shift 7 72110404 Bolt, Carriage 1/4-20 x 1/2 Gr .
22 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS TILLER - - MODEL NUMBER PRR T65D MAINFRAME, RIGHT SIDE 1 185190 Bumper 2 73970500 Locknut, He x, Flange 5/16-18 3 19111116 W asher 11/32 x 11/16 x 16 Ga.
23 12 13 15 16 14 9 9 8 5 18 23 22 21 19 18 3 2 31 7 6 5 4 11 10 29 30 28 18 32 33 34 18 48 60 24 44 18 42 43 41 49 40 39 37 38 37 50 36 20 25 27 35 25 24 44 51 58 53 52 53 transmission_19.5b KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions giv en in U .
24 1 2 29 29 15 1 11 11 12 12 13 14 14 24 23 26 27 22 21 20 19 11 12 16 25 33 32 16 3 4 7 8 9 10 10 23 23 28 24 18 6 10 5 30 tine_shield_16_in 12 12 11 11 10 19 102701X Grip 20 73220600 Nut, Hex 3/8-16 21 102156X Stak e, Depth 22 74930632 Bolt, Hex 3/8-16 x 2 23 4440J Hinge 24 72140404 Bolt, Carriage 1/4-20 x 1/2 Gr .
25 2 11 11 10 9 9 4 4 5 6 7 3 3 1 2 1 1 1 9 9 8 tine_ipb_1 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 4459J Tine, Outer , L.H. 2 132673 Clevis Pin 3 6554J Tine, Inner , L.H. 4 3146R Retainer , Spr ing Zinc 5 132727 Assembly , Hub and Plate, L.
26 1 173196 Decal, CNTRL PNL 2 189872 Decal, Decal, Blt Grd 4 180816 Decal, Instruction, Tilling 5 110614X Decal, Hand Placement 6 102180X Decal, Shift Indicator 7 162384 Decal, caution 9 120076X Deca.
27 LIMITED W ARRANTY The Manuf acturer w arrants to the original consumer purchaser that this product as manuf actured is free from de- f ects in materials and work man ship.
Y our POULAN PRO product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. FOR SER VICE OR REPLACEMENT P AR TS: 1.
Een belangrijk punt na aankoop van elk apparaat Poulan Pro 188904 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Poulan Pro 188904 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Poulan Pro 188904 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Poulan Pro 188904 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Poulan Pro 188904 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Poulan Pro 188904 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Poulan Pro 188904 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Poulan Pro 188904 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
