Gebruiksaanwijzing /service van het product EN250RYLB-O van de fabrikant Procom
Ga naar pagina of 21
1 COMP ACT VENT -FREE FIREPLACE SYSTEM OWNER ’ S OPERA TION AND INST ALLA TION MANUAL Do not store or use gasoline or other flam- mable vapors and liquids in the vicinity of this or any other appliance. WHA T TO DO IF YOU SMELL GAS Do not try to light any appliance.
2 T abel of Contents Safety Information W arnings...................................3 Air for Combustion and V entilation.........................5 Installation.............................................................7 Operating heater............
3 IMPORT ANT : Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.
4 SAFETY INFORMA TION Continued 15. Turn off and unplug heater and let cool before servicing. Only a qualified service person should service and repair heater. 16. Operating heater above elevations of 4,500 feet could cause pilot outage. 17. Do not operate heater if any log is broken.
5 AIR FOR COMBUSTION AND VENTILA TION W ARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventila- tion air. Read the following in- structions to insure proper fresh air for this and other fuel-burning appliances in your home.
6 W ARNING: Rework worksheet, adding the space of the adjoining unconfined space. The combined spaces must have enough fresh air to supply all appliances in both spaces. If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space.
7 NOTICE : This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system's circulating blower while using heater.
8 CONNECTING T O GAS SUPPL Y W ARNING : A qualified service person must connect heater to gas supply. Follow all local codes. CAUTION: Never connect heater directly to the gas supply. This heater requires an external regulator (not supplied). lnstall the external regulator between the heater and gas supply.
9 W ARNING: T est all gas piping and connections for leaks after install- ing or servicing. Correct all leaks at once. W ARNING: Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak.
10 W ARNING: Failure to position the parts in accordance with these diagrams may result in property damage or personal injury. CAUTION: After installation and periodically thereafter, check to en- sure that no flame comes in contact with any log. With the heater set to HIGH, check to see if flames contact any log.
11 b.manual select of main burner: Press BURNER button, the flame is on “MAN” select. At this selection, the main burner will keep working no matter what the temperature is set at. If there is a need to shut off the main burner, just press the “BURNER” button to make the burner on the “OFF” select.
12 3.After completion of the above-men- tioned two steps, the transmitter is kept in a state of readiness. If the appliance doesn’t working for a period time, just pull out the plug from the 1 10V electrical outlet. OPERA TIONS OF KEY -PRESS LOCKING 1.
13 Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 24). With the unit off, lightly blow air through the air inlet hole.
14 TROUBLESHOOTING ODS/pilot lights but flame is continuous igniting and the main burner couldn’t be lit. 1. Thermocouple connection loose at control board 2. Pilot flame not touching thermcouple which allows thermocouple to cool, causing pilot flame to go out.
15 SPECIFICA TIONS Btu 20,000/25,000 20,000/ 25,000 Gas T ype LP Gas Natural Gas Ignition Automatic Automatic Manifold Pressure 8"W.C. 3"W.C.
16 REPLACEMENT P ARTS Note : Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty. P ARTS UNDER W ARRANTY Contact authorized dealers of this product. If they can't supply original replacement part(s) call PRO-COM at (877) 886-5989 for referral information.
17 ILLUSTRA TED P ARTS BREAKDOWN EL250R YLB-O EN250RYLB-O.
18 P ARTS LIST This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 16 of this manual.
19 ILLUSTRA TED P ARTS BREAKDOWN EL250R YLB-O EN250R YLB-O.
20 P ARTS LIST Y E K O N T R A P R E B M U N N O I T P I R C S E DY T Q 10 0 0 3 3 B Ey l b m e s s A s g o L g n i t a r o c e D1 2B 1 0 - 0 4 0 L E) B ( l e n a P p o T1 36 0 - 6 1 0 L El e n a P g .
21 Install the decorating logs. Fasten decorating logs 1 ¡¢ ¡¢ ¡¢ ¡¢ ¡¢ 2 ¡¢ ¡¢ ¡¢ ¡¢ ¡¢ 3 on to the co rresponde nt angle iron ( Figure 4 ). Insert the pinhole on the upper part of log 4 into the pin on the left side of log 1.
Een belangrijk punt na aankoop van elk apparaat Procom EN250RYLB-O (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Procom EN250RYLB-O heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Procom EN250RYLB-O vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Procom EN250RYLB-O leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Procom EN250RYLB-O krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Procom EN250RYLB-O bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Procom EN250RYLB-O kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Procom EN250RYLB-O . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
