Gebruiksaanwijzing /service van het product HPR152F, HPR153F, HPR151W, HPR181W van de fabrikant QSC Audio
Ga naar pagina of 28
1 DSP-30 2.2 XLR Rack-mount, 2 Channel Digital Signal Processor *TD-000097-00* TD-000097-00 Rev .B Hardware Manual.
2 EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsu- lated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans.
3 T able of Contents INTRODUCTION Product Overview ..................................................................4 Front and Rear Panel Illustrations and Dimensions.................4 INST ALLA TION Unpacking........................................
4 Introduction: Overview and Illustrations The DSP-30 and Signal Manager software combine easy-to- use, customizable, two-channel DSP with simple operating- mode selection that requires only two buttons to operate. It can be used with all amplifiers and is housed in a 1-RU , 19-inch rack-mount steel chassis.
5 Introduction: Illustrations and Dimensions Dimensions.
6 Support the Rear for Portable/Mobile Installations If the DSP-30 is to be transported while in a rack, we recommend supporting the rear of the chassis. This will help prevent the unit from being damaged from the increased mechanical stresses of portable and mobile use.
7 Installation: Balanced Audio Connections Connecting Audio Inputs and Outputs All audio connections should be balanced to ensure the best performance. Unbalanced signals may be used if necessary; follow the wiring guidelines below for recommended unbalanced termination.
8 Installation: Unbalanced Audio Connections Connecting Audio Inputs and Outputs Unbalanced inputs can be used if required. If unbal- anced audio sources are used, it is preferable to use an ap- propriate audio transformer (or other unbalanced-to-balanced “converter”) to provide a bal- anced input.
9 Installation: Connecting Audio Inputs and Outputs Audio Connections Once the input and output cables have been properly wired, they can be connected to the receptacles on the rear panel of the DSP-30. INPUTS- Input jacks are “combo” style. They accept either male XLR or 1/4-inch diameter TRS phone plugs.
10 Connecting to the RS-232 Port Connect to the RS-232 port using the 9-pin serial data cable (included in the shipping box). Orient the DB-9 plug correctly, insert the plug fully into the RS-232 port and finger-tighten the retaining screws. The cable length should be 25 feet or less.
11 Installation: System Requirements and Software Installation Software Installation 1. Insert the QSC Signal Manager CD into your drive (typically drive “D:”). If your computer has AUTORUN enabled, the installation will start automatically after several seconds.
12 CH 1 INPUT, CH 2 INPUT - These female XLR-combo jacks are the line-level audio inputs to the unit. TRS or XLR connectors may be used. They are electronically balanced with an input impedance of 8.3k Ohms. If used in an unbalanced configuration, the input impedance is 3.
13 Use: Control, Indicator , and Connector Descriptions RS-232 - This DB-9 female jack is for attaching the serial cable between the unit and the computer. Use this connection for loading your DSP configurations from the computer to the DSP and for “real-time” configuration tuning with Signal Manager software.
14 Use: General Use Guidelines and Preset Description NOTE! The factory setting for all eight presets is wire-through. Signals are passed from input to output without any processing. Y ou may select configurations from the sample files (*.cfg) within Signal Manager or create your own.
15 The DSP-30 must be loaded with your desired presets using the Signal Manager program before use. T est all new presets for expected behavior at low power levels to avoid inadvertently damaging speaker systems. The DSP-30 has eight Preset memories numbered 1 through 8.
16 Use: How to Recall a Preset from the Front Panel TO RECALL A PRESET - 1- Press the BROWSE key until the desired preset number shows in the display . The selection display flashes until Step 2 (below) is completed. 2- Press the ACCEPT key to activate the selected preset in the DSP .
17 TO LOCK THE FRONT P ANEL BUTTONS (Browse and Accept pushbuttons)- 1- Press the Accept button and hold it down for at least three seconds. 2- The “lock” indicator will illuminate. 3- The Browse button is disabled. FRONT P ANEL DISPLA Y - Example shows Preset 7 in “ unlocked ” and “ locked ” state.
18 Use: Contact Closure Feature Contact Closure Feature The contact closure feature is used to trigger gain changes in the DSP . Any configuration that uses one or more switched gain objects (see Signal Manager software Help file ) can take advantage of this feature.
19 Use: RS-232 Pinout Pin Signal Description 1 DCD 2 T D 3 R D 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 Contact Closure RS-232 Pinout: The diagram below shows the pin assignments for the female RS-232 connector on the DSP . *Note! Pin 9 is used for contact closure input.
20 TRI-AMPED P A CABINETS WITH SUBWOOFER (refer to illustration at right) Use: Application Example This is highly generalized, but shows the main idea in cre- ating larger systems. In this example, the audio source material is connected to the inputs of all four DSP’ s.
21 Use: Application Example TRI-AMPED P A CABINETS WITH SUBWOOFER: Sample Application Diagram.
22 Specifications Frequency response 20 Hz–20 kHz ±0.4 dB at 1dB below full scale input voltage (all sensitivities) Distortion <0.007% THD+N @ 1dB below full scale output, all sensitivities, 20 Hz– 20 kHz Group Delay 1.00 milliseconds Dynamic range >95dB unweighted, 1.
23 Physical Chassis Type Steel (chassis & covers) Height 1.73 inches Width 18.9 inches (including rack ears) Depth 14.9 inches (including rear ears) 13.
24 Architect ’ s and Engineer ’ s Specification The Digital Signal Processor (DSP) shall provide two independent channels of DSP for signal delivery to all professional power amplifiers. Input and output sensitivity shall be adjustable to accommodate consumer and pro audio signal levels.
25 Maintenance, Warranty & QSC Contact Information Cleaning The faceplate and chassis can be cleaned with a soft cloth and nonabrasive, mild cleaning solution. Products like Simple Green and Windex work well. Do not use powders or scrubbing pads of any type as they are usually abrasive and will permanently damage the finish of your DSP-30.
26 Notes.
27 Notes.
28 1675 MacArthur Boulevard Costa Mesa, California 92626 USA PH: (714) 754-6175 FAX: (714) 754-6174 © Copyright 2001, QSC Audio Products, Inc. QSC ® is a registered trademark of QSC Audio Products, Inc., Costa Mesa, CA “ QSC ” and the QSC logo are registered with the U.
Een belangrijk punt na aankoop van elk apparaat QSC Audio HPR152F, HPR153F, HPR151W, HPR181W (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen QSC Audio HPR152F, HPR153F, HPR151W, HPR181W heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens QSC Audio HPR152F, HPR153F, HPR151W, HPR181W vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding QSC Audio HPR152F, HPR153F, HPR151W, HPR181W leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over QSC Audio HPR152F, HPR153F, HPR151W, HPR181W krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van QSC Audio HPR152F, HPR153F, HPR151W, HPR181W bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de QSC Audio HPR152F, HPR153F, HPR151W, HPR181W kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met QSC Audio HPR152F, HPR153F, HPR151W, HPR181W . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
