Gebruiksaanwijzing /service van het product ISIS 215PCM van de fabrikant QSC Audio
Ga naar pagina of 41
1 User Manual TD-000105-00 rev .A *TD-000105-00* ISIS 215SB ISIS 215PCM 2 x 15” W eather-Resistant Subwoofer Cabinet with Speakon™ Input C onnec tor Integra ted, Self-Po wered—Self-Processed, In.
2 © Copyright 2002, QSC Audio Products, Inc. QSC® is a registered trademark of QSC Audio Products, Inc. “QSC” and the QSC logo are registered with the U.S. Patent and T rademark Office All trademarks are the property of their respective owners. Speakon™ is a registered trademark of Neutrik Inc.
3 INTRODUCTION General Overview ...........................................................................................4 T echnical Overview ........................................................................................6 Block Diagram...
4 INTRODUCTION- General Overview Introduction Thank you and congratulations on your purchase of the ISIS 215PCM Powered-System Control Module or 215SB Subwoofer . This product represents the state-of-the-art in all-weather , lightweight SR (sound reinforcement) loudspeaker systems.
5 INTRODUCTION- General Overview T ransporting the 215PCM using integral wheels and handles. 215PCM Front A 16” length of “L-track” flying hardware is featured on all four corners of the cabinet. Pole cups are featured for either cabinet orientation.
6 INTRODUCTION- T echnical Overview T echnical Overview: CH1 and CH2 Inputs are connected to the T op Box Processor and to the Mode Switch. In Combination Mode, the Mode Switch connects CH1 and CH2 Inputs to the Subwoofer Processor as well.
7 INTRODUCTION- Block Diagram.
8 The 215PCM is highly durable and is carefully packaged and crated. We recommend you inspect the unit carefully after removing it from the packaging, as occasionally there may be damage due to some unfortunate incident during shipment. Report any damage to the shipping carrier .
9 Install the Signal Manager software on the PC that will be used to configure the 215PCMs processors. See page 20. Put the 215PCM in a location that: • ....is close enough to the PC to connect the serial cable. •....has 120V , 30A service to power the 215PCM.
10 Adjusting the Gain Settings of the Amplifiers PREP ARA TION FOR FIRST USE- Amplifier Gain Controls Ordinarily , the Gain controls of the amplifiers are left set at full gain. This is not recommended for first-time users of freely- configurable DSP .
11 The 215PCM requires 120 V olt, 30 Amp AC service. Attempting full power operation on lower rated circuits may overheat wirirng and cause breakers to switch off. Use only heavy-duty 12 or 10 ga. extension cords. The 215PCM requires a 120 V olt, 30 Amp connection to the AC mains.
12 T o Configure a Processor (215PCM only) Each Processor has a 9-pin “D-sub” connector labeled RS-232. The RS-232 connection is used to configure the Processor by connecting to the PC’ s COM port. Important points: – The 215PCM must be ON (powered up) in order to configure the Processors.
13 CONNECTIONS- Mode Switch and Signal Routing The position of the Mode Switch determines how the input signals are routed. Select your operating mode before making connections. If you are using the DataPorts for audio input, the Mode Switch has no effect.
14 Audio Connections Audio inputs can be connected to the XLR inputs OR the DataPort connections (QSControl users). This section provides information on using the XLR Inputs, For DataPort information see page 17. CONNECTIONS- Audio Connections: XLR Inputs CH1 and CH2 INPUT - In Combination Mode, use these for 2-channel inputs.
15 XLR Connections The XLR inputs are electronically balanced. T o maintain the benefits of balanced, pro-audio connections, make all connections to the 215PCM using balanced, high-quality cable and connectors. If balanced inputs are not available, use a unbalanced-to-balanced converter , such as a “DI” box or proper audio transformer .
16 CONNECTIONS- Post Processor Outputs Post Processor Outputs Each processor has two post-processor outputs. They are labeled CH1 OUTPUT and CH2 OUTPUT . The audio present at these outputs is processed and the signal is the same as at the OUT1 and OUT2 blocks in the Signal Manager software.
17 CONNECTIONS- DataPort (QSControl users only) When using the DataPort connections for audio inputs, do not use the XLR audio inputs. Any signals present on both connections will be summed, producing unexpected results. It is OK to use the XLRs for audio input if the DataPort connection is used only for control and monitoring.
18 CONNECTIONS- Output to T op Boxes (Speakons™) Output to T op Boxes At the right side of the rear panel are the output connections to the top box speakers. Note the color coding scheme of the text labels for each Speakon connector . The color coding corresponds with the colors of the Mode Switch labels (Combination Mode or Discrete Mode).
19 USE- Cooling Air Inlet and Exhaust V ents The 215PCM contains two forced-air cooled QSC Powerlight 2-series amplifiers. They are mounted within the back portion of the enclosure. The amplifi- ers rely upon an unobstructed air flow in and out of the respective vents, shown below .
20 USE- AC Power Switch and LED Indicators LED Indicators Each Processor has two LED indicators, PWR and SIGNAL. The indicators are located on the rear panel of the 215PCM. PWR- When the 215PCM is connected to a properly rated and working AC supply circuit and is turned on, the blue PWR LED on each of the Processors will illuminate.
21 IMPORT ANT USER CAUTION USE- LED Indicators (continued) and Important User Caution The 215PCM has been equipped with a very powerful internal amplifier . The amplifier power is several times greater than the long-term power capacity of the drivers.
22 PROCESSOR USE- Software Installation and System Requirements 1. Insert the QSC Signal Manager CD into your drive (typically drive “D:”). If your computer has AUTORUN enabled, the installation will start automatically after several seconds. If it does not, then proceed to step 2, below .
23 PROCESSOR USE: General Guidelines and Preset Description NOTE! The factory setting for all eight Preset memories is wire- through. Signals are passed from input to output without any processing. Each Processor must be configured as desired by the user .
24 Each Processor must be loaded with your desired signal processing configu- ration using the Signal Manager program before use. T est all new configura- tions for expected behavior at low power levels to avoid inadvertently damaging speaker systems.
25 Processor Use: Configuring the Processors (Discrete 2.1) How the Processors are configured is dependant on the system setup and desired results. For example, a discrete 2.1 system requires a different signal chain than a mono 3-way stack. Decide how your system will be set up before starting to configure the Processors.
26 Example 1- Discrete 2.1 (continued) The Subwoofer Processor is next. In Discrete Mode, the Subwoofer Processor’ s input signal comes from the Input 3 XLR. Input 3 is routed to the Subwoofer Processor’ s IN1 block (see example, below). The IN2 block is not placed when operating in Discrete Mode.
27 Processor Use: Configuring the Processors (3-way Mono Stack) Example 2- Active 3-way Mono Stack In a 3-way configuration, the T op Box amplifier’ s two channels are used for low- and high-frequencies and the subwoofer handles bass. The Processors perform the required crossover and time delay functions.
28 TROUBLESHOOTING The 215PCM “cuts-out” when I really crank it up (intermittent operation)- • Make sure the AC power source is rated for 120V , 30 Amps. Do not use 20 or 15 Amp AC supply circuits for the 215PCM! Use only 12 or 10 gauge heavy-duty extension cords.
29 TROUBLESHOOTING Unable to “talk” to processor from Signal Manager software (OFFLINE status indicated)- • Check that the serial cable is a normal serial data cable. Null-modem type cables will not work. • Make sure that the serial cable is properly connected on both ends and that the retaining screws are snug (finger tight).
30 TROUBLESHOOTING I am using the 215PCM setup for biamp operation, but my mid- and high-frequency sound seems to be gone- • Make sure the Mode Switch is in the correct position for your intended application. • Be sure you are using only the upper Speakon for 4-wire biamp connection.
31 Specifications- ISIS 215SB SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Dimensions.
32 Specifications- ISIS 215SB Acoustic Performance SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
33 Specifications- ISIS 215SB 215SB Specifications Frequency Range Recommended Bandpass: 35- 150 Hz (±3 dB) Frequency Response: 36- 360 Hz (-3dB) Usable Frequency Range: 29- 440 Hz (-10 dB) Maximum O.
34 Specifications- ISIS 215PCM SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Self-Powered Dimensions.
35 Specifications- ISIS 215PCM 215PCM System Specification Description 215 PCM: Comprised of the 215SB Subwoofer Cabinet with a “backpack” containing two QSC DSP-3 24-bit Signal Processors, 1 ruggedized QSC PL230 3000 Watt amplifier and 1 ruggedized QSC PL236 3600 Watt amplifier.
36 A mplifier Specifications Output Power in watts Subwoofer Amplifier (PL230 type) 4 Ohms, 1 kHz, 1% THD 3000 Watts Top Box Amplifier (PL236 type) FTC: 8 Ohms per channel (20- 20 kHz.
37 Specifications- ISIS 215PCM Processors Note: Specifications are subject to change without notice. Digital Signal Processor Specifications Type Freely configurable, custom DSP with software for PC. Computer connection needed only for set up. Signal Processing Two QSC DSP-3 Processors, 24 bit, 48 kHz.
38 APPENDIX- Contact Closure Wiring Details Contact Closure Feature The contact closure feature is used to trigger gain changes in the DSP . Any configuration that uses one or more switched gain objects (see Signal Manager software Help file ) can take advantage of this feature.
39 Pin Signal Description 1 DCD 2 T D 3 R D 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 Contact Closure RS-232 Pinout: The diagram below shows the pin assignments for the female RS-232 connector on the DSP-3 Processors featured in the 215PCM. *Note! Pin 9 is used for contact closure input.
40 Disclaimer QSC Audio Products, Inc. is not liable for any damage to amplifiers, or any other equipment that is caused by negligence or improper installation and/or use of this speaker product.
42 QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA “QSC” and the QSC logo are registered with the U.S. Patent and T rademark Office.
Een belangrijk punt na aankoop van elk apparaat QSC Audio ISIS 215PCM (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen QSC Audio ISIS 215PCM heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens QSC Audio ISIS 215PCM vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding QSC Audio ISIS 215PCM leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over QSC Audio ISIS 215PCM krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van QSC Audio ISIS 215PCM bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de QSC Audio ISIS 215PCM kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met QSC Audio ISIS 215PCM . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
