Gebruiksaanwijzing /service van het product A12001DT van de fabrikant Audiobahn
Ga naar pagina of 20
CLASS D AMPLIFIERS A18001DT A12001DT A8001DT OPERA TING INSTR UCTIONS PLEASE RET AIN MANU AL FOR FUTURE USE AND REFERENCE QU ALITY , RELIABILITY , & PURE BLISS.
The Audiobahn W ay T o bring the product to market that excites the consumer through sound and vision from an orientation of integrity and customer service. We make you look as good as you sound. We strive to take car audio to an extreme the world has never seen, and a world that never stops evolving.
Table of Contents Table of Contents 2 Introduction Features and Specifications Control and Functions Planning / Mounting Your System Adjusting and Tuning Troubleshooting Wiring Diagram Warning and Dis.
Introduction Dear Customer , Congratulations on your purchase of the worlds finest brand of car audio products. Here at Audiobahn Inc. we are devoted to making our musical reproduction the vert best, and we are pleased you have chosen our product.
1-CHANNEL HIGH OUTPUT CLASS D AMPLIFIER DOUBLE SIDED CIRCUIT BOARD DUAL COOLING FANS VARIABLE LOW PASS FILTER REMOTE BASS BOOST CONTROL DIGITAL DISPLAY VOLT-METER L.E.D. ILLUMINATED HEAT SINK VAIRIABLE LOW PASS FILTER 50Hz - 150Hz VARIABLE BASS BOOST 0 - 18dB INPUT SENSITIVITY 200mV to 8V TYPICAL CURRENT DRAW 1.
Controls and Functions 5.
Controls and Functions 6 This plug connects the amplifier and the remote bass knob using the supplied cable. This control adjusts the amplifier's input sensitivity . The input sensitivity is variable from 200 Millivolts to 8 volts. T urning clockwise increases sensitivity .
Controls and Functions 7 The LINE OUT allows you to build a multiple amplifier system without having to use splitter cords or Y -adapters to distribute the signal. Now it is simply a matter bringing one set of RCAs into the first amplifier , then using the line out RCA jacks as the feed to the next amplifier .
8 Controls and Functions For use as a dedicated subwoofer channel, set the filter switch to the "LPF" (Low Pass Frequency). Adjust the variable crossover frequency with control knob as desired. The amplifier input circuit filters out everything above 50Hz .
Controls and Functions 9 These terminals are used to wire your subwoofer(s) to the amplifier . T o avoid unwanted ignition noise caused by ground loops, it is essential that the amplifier be grounded to a clean, bare, metal of the vehicle's chassis.
Controls and Functions 10 The remote terminal needs to be wired to the car's stereo or source unit remote turn on wire. This amplifier is turned on remotely when the vehicle's stereo is turned on.
b. Are your components matched? The RMS power rating of your speakers must be equal or greater than the Amplifier's. They also must be 1-8 Ohms impedance (this information is normally printed on the speaker magnet). c. Consider both the length of your leads, and routing when determining the mounting location.
Wiring Diagram 12 MONO MODE.
Bridging 2 Amplifiers 13 Master Slave Master Slave BRIDGED BRIDGED IF BRIDGED SWITCH POSITION IS ON SLA VE, ALL CONTROLS ARE NON-FUNCTIONAL. ALL CONTROLS ARE NOW CONTROLLED BY THE MASTER AMPLIFIER.
Bridging 2 Amplifiers 14.
Adjusting and T uning 15 ADJUSTING THE GAIN / LEVEL SETTING Below you will find information on adjusting the amplifiers gains. Adjusting the gain correctly is essential to proper operation of the amplifie r .
Separate speaker wires and insulate Speaker wires short STATUS LAMP ON Temperature shut down Be sure proper speaker load impedance recommendations are observed. (If you use an ohmmeter to check speaker resistance, please remember that DC resistance and AC impedance may not be the same.
Investigate the layout of your automobile thoroughly before drilling or cutting any holes. T ake care when you work near the gas tanks, lines, hydraulic lines, and electrical wiring. Do not use the power amplifier unmounted. Attach the system securely to the automobile to prevent damage, particularly in the event of an accident.
W arranty 18.
How to receive warranty service: Contact your local Authorized Audiobahn Dealer , or call Audiobahn at (800) 488-8595 between the hours of 9:00 AM and 5:00 PM PST .
Een belangrijk punt na aankoop van elk apparaat Audiobahn A12001DT (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Audiobahn A12001DT heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Audiobahn A12001DT vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Audiobahn A12001DT leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Audiobahn A12001DT krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Audiobahn A12001DT bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Audiobahn A12001DT kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Audiobahn A12001DT . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
