Gebruiksaanwijzing /service van het product USBN-500 van de fabrikant Quatech
Ga naar pagina of 18
Quatech Model USBN-500 Network USB2.0 Device Server Over IP 4-Port USB2.0 Device USER MANUAL.
USB Device Server Windows Client User Manual TABLE OF CONTENTS 1. Introduction______________________________________________________________3 2. Windows utility____________________________________________________________3 2.1. Virtual USB-IP Driver Software_________________________________________4 2.
2. Windows utility USBIP Admin utility Setup is an Install Shield ba sed application, which can be used for installing, uninstalling and upgrading this USB device server Client S/W. Pl ease run the self-explanatory Install shield application to install this USB device se rver Admin Utility.
USBIP Admin tool The application has four panels, wh ich are docked in the application. 1) Main window: This displays all the Device server and the USB Devices connected on them 2) Function Panel: This panel enables to switc h between the Device Mapping and Server Manager Application.
and the Operating System autom atically searches for the driver until the Virtual USB over IP driver is installed. Make sure that you click on “Continue anyway” if a Windows dialog pops up about the Digital Signature as shown below.
2.3. Server Manager Server manager enables the Administrator to c onfigure the USB device server on the network. The Server Manger also has an option to s earch for the USB servers on the Network. Right Click on Server Manager Main window and Click on “Search server” as shown below.
It pops up the ‘Searching for Servers’ dialog and li st all the USB device se rvers on the Network as shown below The USB Device Server search is password protected and should be unlocked in order to configure the selected device.
On selecting ‘Un-Lock’ the password dialog pops up as shown below. Key in the password in the ‘Password’ dialog. The default password for the USB IP Server is “usbip” If the Authentication is successful a ‘Unlock OK’ dialog appears. Now the Device server can be configured for various settings as given below.
The Basic Settings page allows you to specify a server name .Check the modify box and enter server name as shown below. IP Settings Page: The IP Settings page allows you to modify the US B device server IP Address as shown below. The Default IP Address is 192.
After Selecting IP Configuration key in the IP Ad dress of the USB device server in the IP Address field followed by proper Subnet Mask & Gate Way as shown below. After entering IP address, Subnet Mask & Gate Way then click on “save” button.
Check the Modify box to Enable or Disable password option to the USB device server. b) Upgrade Firmware This USB device server Firmware can be upgraded remotely using the Firmware upgrade option. Select the server on the Server manager. Right Click on the server and Select Upgrade Firm ware option to upgrade the firmware.
As soon as the transfer is completed, the USB de vice server automatically restarts to apply the upgraded firmware settings. c) Restore factory defaults Right click on the USB device server under Serv er Manager Window and select the Restore Factory Defaults function to obtain Default settings as shown below.
the Printer Auto Reconnect button on the Menu bar to open the Printer Auto-Connect Window. Select the Printer which was connected a nd Click on “Save” and close the Window.
browser, which will displays the default hom e page of the Server. Def ault IP address is 192.168.3.22, for USB Server application & the USB devi ce server will have this IP address when USB Server Firmware is loaded on to it. http://192.168.3.22 On password prompt please give ‘ admin ’ as user name and ‘ usbip ’ as password.
For the wired interface you can configure the Stat ic IP, Subnet Mask, and Gateway m anually or set the box to automatically obtain an IP address by setting to the Dyna mic (DHCP) mode. 3.4. Status Page The status page displays the current status of the USB devices attached.
a ) T h r e a d S t a t u s : T h r e a d S e s s i o n H o s t A c t i o n b ) S e r v i c e S t a t u s : S e r v i c e S t a t u s C o n t r o l c ) D e v i c e S t a t u s : Vendor Id Product Id C.
An upgrade.tar.bz2 file is required to upgrade the firmware. Click on “upgrade” to upgrade the firmware.
A file successfully uploaded message is displaye d and the webpage also indicates that the USB device server is restarting to a pply the upgraded firmware settings.
Een belangrijk punt na aankoop van elk apparaat Quatech USBN-500 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Quatech USBN-500 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Quatech USBN-500 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Quatech USBN-500 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Quatech USBN-500 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Quatech USBN-500 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Quatech USBN-500 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Quatech USBN-500 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
