Gebruiksaanwijzing /service van het product 43-3827 van de fabrikant Radio Shack
Ga naar pagina of 48
© 2003 RadioShack Corporation. All Rights Reserved. RadioShack and RadioShack.com are trademarks used b y RadioShack Corporation. E NERGY S TAR and the E NERGY S TAR certification mark are registered US marks. OWNER’S MANUAL Please read before using this equipment.
Important Safety Instructions 2 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions.
Important Safety Instructions 3 11. Slots and openings in the telephone’ s cabinet and the back or bottom are pro vided for ventilation. T o protect the telephone from ov erheating, these openings must not be b loc ked or co vered. The openings should ne ver be bloc ked b y placing the product on a bed, sof a, rug, or other similar surface.
Battery Safety Instructions 4 • If the product has been e xposed to rain or water . • If the product does not operate normally by f ollowing the operating instructions.
Introduction 5 • Charge the batter y pack pro vided with or identified f or use with this product only in accordance with the instructions and limitations specified in the instruction manual provided f or this product. • Obser v e proper polarity or ientation between the batter y pack and battery charger .
Important Caller ID Information 6 • caller’ s number only • caller’ s name only • caller’ s name and number If you subscribe to Call Waiting ID and Caller ID, the system can show you the incoming caller information, even when you are already talking on the phone.
Installation 7 INSTALLATION M OUNTING THE P HONE You can place the phone on a desk or table, mount it on a standard wall plate, or directly on a wall. Choose a location that is: Ô • near an A C out.
Installation 8 3. Inser t the supplied AC adapter’ s barrel plug into the DC IN 9V jack on the bac k. 4. Route the adapter’ s cord through the strain relief slot on the base’ s bottom. 5. Plug the adapter into a standard A C outlet. 6. Lift the base’ s antenna to a ver tical position.
Installation 9 F or direct wall mounting , align the base’ s keyhole slots with the mounting screws and slide the base downw ard to secure it. 5. Plug the adapter into a standard A C outlet.
Installation 10 When you first use the phone after charging or recharging the battery pack, the phone might not work and you might hear error beeps. If this happens, return the handset to the base for about 5 seconds to change the security access-protection code.
Installation 11 area. RadioShack’s involvement in this program is part of the company’s commitment to preserving our environment and conserving our natural resources. S ETTING M ENU O PTIONS There are five setup options available. They are Caller ID options [AutoTalk, CIDCW (Caller ID on Call Waiting), and Area Code], Dial Mode and Language.
Installation 12 from outside your local area code, you will see a full 10-digit number. 1. When the phone is in the standby mode , press and hold CID/MENU . 2. Press 3 or press $ twice to select A A A A r r r r e e e e a a a a C C C C o o o o d d d d e e e e .
Operation 13 Setting the Language 1. When the phone is in the standby mode , Press and hold CID/MENU . 2. Press 5 or press $ f our times to select L L L L a a a a n n n n g g g g u u u u a a a a g g g g e e e e . 3. Press SEL to toggle between E E E E n n n n g g g g and F F F F r r r r .
Operation 14 A DJUSTING THE H ANDSET R INGER AND E ARPIECE V OLUME Handset Ringer Tone and Volume Press # or $ in standby mode to select one of five ringer tones and volume combinations. Earpiece Volume Press # or $ repeatedly during a call to change the earpiece volume of the handset.
Operation 15 call. For example, entering your bank account number after you have called your bank. Ô Initially make your call with the pulse dialing mode. Once your call connects, press ∗ /T ONE/ & . Enter the desired number. These digits will be sent as tone dialing.
Memory Dialing 16 MEMORY DIALING S TORING P HONE N UMBERS AND N AMES Memory Dialing allows you to dial a number using just a few key presses. Your phone stores up to 10 names/numbers in the handset. Ô 1. Press and hold MEM until M M M M e e e e m m m m o o o o r r r r y y y y S S S S t t t t o o o o r r r r e e e e is displa yed.
Memory Dialing 17 6. Use the number k eys to enter the phone number . The phone number cannot e xceed 20 digits. Ô • Use PA USE/RDL to enter a pause in the dialing sequence. The display shows a P P P P . Each pause counts as one digit and represents a two second dela y of time between the digits as the y are sent.
Memory Dialing 18 Upper case letters first, lower case letters next, and finally the number corresponding to the key. If You Make a Mistake while Entering a Name Use ∗ /T ONE/ & or #/ % to move the cursor to the incorrect character, press CH/DEL to erase up to the wrong entry, then enter the correct character.
Memory Dialing 19 M AKING C ALLS WITH M EMORY D IALING Memory Dialing from Standby Mode 1. Press MEM . The handset displays y our programmed memory locations. 2. Press # or $ , or enter a number (0 - 9) to select the memor y location you w ould like to dial.
Memory Dialing 20 the location number where the special number has been stored. Store your special number with an identifying name. (Refer to “Storing Phone Numbers and Names” on page 16.
Memory Dialing 21 If you don’t w ant to change the phone number , skip this step . 8. Press SEL . Y ou hear a confir mation tone. The memor y storage is complete .
Memory Dialing 22 Testing Stored Emergency Numbers If you store an emergency service’s number (police department, fire department, ambulance) and you choose to test the stored number, make the test call during the late evening or early morning hours to avoid peak demand periods.
Caller ID 23 D ELETING THE S PEED D IAL 1. When the phone is in the standby mode , press and hold SPEED DIAL . 2. Press # or $ to select D D D D e e e e l l l l e e e e t t t t e e e e N N N N u u u u m m m m b b b b e e e e r r r r . 3. Press SEL . 4.
Caller ID 24 W HEN THE T ELEPHONE R INGS 1. When the Caller ID message is received, the displa y shows the caller’ s phone number along with the date and time. The incoming call inf or mation is stored in the Caller ID record. If the Caller ID ser vice includes the caller’ s name, the caller’ s name appears on the display (up to 15 letters).
Caller ID 25 V IEWING THE C ALLER ID M ESSAGE L IST The Caller ID list stores information for up to 30 incoming calls - even unanswered calls. Ô 1. Press CID/MENU . The summar y screen appears. This screen shows the number of ne w messages and total messages.
Caller ID 26 When the pointer is at N N N N o o o o : The displa y retur ns to the Caller ID message. Deleting all Caller ID Names/Numbers 1. Press CID/MENU . 2. Press CH/DEL . 3. Press # or $ to select Y Y Y Y e e e e s s s s or N N N N o o o o . 4. Press SEL or CH/DEL .
The Integrated Answering Device 27 make your changes, and then press talk/FLASH . This will not change the number in the Caller ID list memory. Storing Caller ID Messages in Memory dialing Messages shown in the Caller ID list can be stored in memory dialing.
The Integrated Answering Device 28 F EATURES Digital Tapeless Recording allows you to quickly review, save, or delete the messages you choose. You will never have to worry about a tape wearing out, jamming, or resetting improperly.
The Integrated Answering Device 29 S ETTING UP Y OUR A NSWERING S YSTEM Using the Menu Mode The Menu mode allows you to set the following Answering System functions. Ô •T o scroll through the menu options, repeatedly press MENU . The system returns to standby after the last menu option.
The Integrated Answering Device 30 2. Press V OL/SEL/ # or V OL/SEL/ $ until the correct da y is announced. The n umbers [ ] through [ ] are display ed on the base. 3. Press SET/RING to select the da y . 4. Press V OL/SEL/ # or V OL/SEL/ $ until you hear the correct hour setting.
The Integrated Answering Device 31 Then the system announces the guidance f or setting the PIN code. 2. Press V OL/SEL/ # or V OL/SEL/ $ until the desired number appears. 3. Press SET/RING to select the PIN code. Y ou hear a confirmation tone, then the announcement “Security code” and the ne w PIN code is announced.
The Integrated Answering Device 32 Selecting the message record time You have three record time options. The options “ 1 minute” or “ 4 minutes” set the duration for recording the incoming messages. “ Announce only ” answers the call with the preset greeting or your personal greeting but prevents the caller from leaving a message.
The Integrated Answering Device 33 Setting the Message Alert tone Message Alert feature lets you know you have new messages by sounding a short beeping tone. If you set the Message Alert to On and when a new message is received, the alert tone will sound every 15 seconds.
The Integrated Answering Device 34 Selecting the Language The answering system voice announcements can be heard in English or French. To choose the language of the answering system voice announcements: 1. Press MENU six times in standby mode . Y ou hear the announcement “Language, English” f ollowed b y the guidance for setting the language.
The Integrated Answering Device 35 3. When you are finished recording y our greeting, press OGM , PLA Y/ST OP or SET/RING . Y ou hear a confirmation tone, and then your greeting pla ys back f or you. $ $ $ $ Choosing between the two outgoing messages Press OGM .
The Integrated Answering Device 36 The numbers - are displayed on the base indicating the volume levels. being the softest and being the loudest. U SING Y OUR A NSWERING S YSTEM The message counter displays the number of messages stored in memory. If the display flashes, then there are new messages are waiting for you.
The Integrated Answering Device 37 2. After a message has pla yed f or a f ew seconds, press ' to repla y the message. If you ha ve se veral messages , press ' repeatedly until you return to the message you w ant to replay . 3. Press PLA Y/ST OP at any time to stop re viewing messages and return to standby .
The Integrated Answering Device 38 You can also delete all the messages. 1. Press DELETE in standby mode . Y ou hear an announcement “T o delete all messages, press delete again”. 2. Press DELETE again. Y ou hear a confirmation tone and is displa yed on the base.
The Integrated Answering Device 39 Recording a conversation You can record up to 10 minutes of conversation while you are using your phone. ! Ô 1. During a conv ersation from the handset, press and hold MEMO . The unit begins recording and [] flashes on the message counter .
The Integrated Answering Device 40 4. Y ou ma y continue to listen to the Help Guidance, or y ou may select a command from the f ollowing char t. Ô *For Memo Record and Greeting Message Record function, the first time you enter the corresponding command, it starts the Recording function.
The Integrated Answering Device 41 Turn on the answering system remotely If you have forgotten to turn on your answering system, you can turn it on remotely from any touch- tone telephone. 1. Call your telephone n umber . 2. W ait ten rings until the system answers .
Additional Information 42 ADDITIONAL INFORMATION I NSTALLING THE OPTIONAL B ELTCLIP To attach the beltclip Insert the beltclip into the holes on each side of the handset. Press down until it clicks. To remove the beltclip Pull both sides of the beltclip to release the tabs from the holes.
43 Troubleshooting TROUBLESHOOTING If your phone is not performing to your expectations, please try these simple steps first . Problem Solution The CHARGE/IN USE LED won’t illuminate when the handset is placed in the base. Make sure the A C adapter is plugged into the base and wall outlet.
44 Troubleshooting If you still have problems, disconnect the phone. If other phones on the same line work properly, the fault is in this phone or its installation. If you cannot find the problem, take your phone to your local RadioShack store for assistance.
Care 45 CARE Keep the phone dry; if it gets wet, wipe it dry immediately. Use and store the phone only in normal temperature environments. Handle the phone carefully; do not drop it. Keep the phone away from dust and dirt, and wipe it with a damp cloth occasionally to keep it looking new.
FCC Statement 46 FCC STATEMENT Your telephone compiles with Part 68 of the FCC Rules.Upon request, you must provide the phone’s FCC registration number and REN to your phone company. These numbers are on the base unit. Your phone is not intended to be used with party- line systems.
47 S URGE P ROTECTION Your telephone has built-in protection circuits to reduce the risk of damage from surges in telephone line and power line current. These protection circuits meet or exceed the FCC requirements. However, lightning striking the telephone or power lines can damage your telephone.
43-3827/43-3870 UCZZ01394ZB 07A03 Printed in China RadioShack Corporation Fort Worth, Texas 76102 Limited One-Y ear Warranty This product is warranted b y RadioShack against manuf acturing defects in .
Een belangrijk punt na aankoop van elk apparaat Radio Shack 43-3827 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Radio Shack 43-3827 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Radio Shack 43-3827 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Radio Shack 43-3827 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Radio Shack 43-3827 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Radio Shack 43-3827 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Radio Shack 43-3827 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Radio Shack 43-3827 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
