Gebruiksaanwijzing /service van het product XL-400 van de fabrikant Radio Shack
Ga naar pagina of 24
Owner’s Manual Please read before using this equipment. XL-400 High Power 4/3/2-Channel Bridgeable Amplifier 12-2018.fm Page 1 Friday, May 12, 2000 12:46 PM.
2 ˆ Contents Features ........... .............. .............. .............. .............. ................. .............. .............. ...... ........ .... 3 Preparation ......... .............. .............. .............. .............. ...
3 Features ˆ Features Your RadioShack High Power 4/ 3 /2 - C ha n- nel Bridgeable Amplifie r produces a total of 400 watts to give added punch and power to your vehicle’s existing auto sound system. The amplifier produces up to 200 watts per channel (if bridged) of clean, pow erful sound at all audio frequencies with minimum distor- tio n.
4 Preparation ˆ Preparation SUPPLIED HARDWARE Your amplifier comes with the follo wing items. Be sure you locate everything shown before you store or dispo se of the pa cki n g mate ri al s. BEFORE Y OU BEGIN THE INSTALLATION Before you install your amplifier, read all the instructions in this owner’s manual.
5 Preparation Warning: The amplifier gets very hot while it is on. Do not touch the a mplifier or place flammable objects near it. Preparing the Mounting Area Before you mount the amplifier, make su re you have these materi als.
6 Preparation Cautions: • For added safety and to protect your amplifier and auto sound system, dis- connect the cable from your vehicle’s negative ( – ) battery terminal be fore you begin.
7 Preparation This connection turns on the ampl ifier when you turn on the auto sound sys- tem, and turns off the amplifier when you turn off the auto sound system. This prevents your vehicle’s battery from being drained if you lea ve your amplifier on when you turn of f your auto sound system.
8 Connecting Inputs ˆ Connecting Inputs LOW-LEVEL INPUTS You can connect your auto sound system’s low-level line out jacks to the amplifier’s low- level line in jacks. If your auto sound system does not have low-level line out jacks, see “Hig h-Level (Speaker Wire) In puts” on Pa ge 9 to connect your amplifier.
9 Connecting Inputs If your auto sound system has two li ne out jacks (left and right) , connect the auto sound system to th e amplifier . Note: For the best results, use shielded au dio Y-adapters (not supplied) available at your local RadioShack store.
10 Connecting Inputs Four Speaker Outputs Floating Grou nd Connection Common Ground Con nection Gray/Black White/Bl ack Gray White Right Rear + Speaker Left Rear + Speaker Violet/Black Gree n/Black Vi.
11 Connecting Inputs Two Speaker Outputs Floating Grou nd Connection Common Ground Con nection Right + Speaker Left + Speaker Violet/Black Green /Black Violet Green Left – Speaker Right – Speaker .
12 Connecting Inputs CONNECTING SPEAKERS You can connect four speakers, tw o speak- ers and a subwoofer, or just two speakers to the amplifier and your auto sound system. Important: Before you make the connec- tions, make sure both BRG/ST switches (on the left and right sides of the amplifier) are set to ST .
13 Connecting Inputs Connecting Four Speakers 1. Use a screwdriver to connect the front left speaker ’s positive (+) wire to the amplifier ’s CH1 (+) terminal. 2. Use a screwdriver to connect the front left speaker ’s negative (–) wire to the amplifier ’s CH1 (–) terminal.
14 Connecting Inputs Connecting T wo Speakers (Bridged Connection ) Caution: This connection produces 200 watts per channel. Use this co nnection only if you have high-power sp eakers th at can han- dle a power output of 200 watts. Note: CH2 (+) and CH4 (+) are used as nega- tive (–) terminals for a bridged connection.
15 Connecting Inputs 4. Use a screwdriver to connect the sub- woofer ’s positive (+) wire to the ampli- fier ’s CH3 (+) or CH4 (+) terminal. 5. Repeat Step 4 to connect the sub- woofer ’s negative (–) wire to the ampli- fier ’s negative (–) terminal for the same channel you connected in Step 4.
16 Completing the Installation ˆ Completing the Installation T ESTING THE CONNECTIONS Before you continue, make sure you have securely made all connections.
17 Completing the Installation 5. Secure the amplifier to the mounting surface using the supplied she et metal screws and washers. 6. Reconnect the wiring. 7. Reconnect the cable to the vehicle bat- tery’s negative (–) terminal. 8. Reset your vehicle’ s clock, your auto sound system’s tuner memory , and other timer/memory devices.
18 Operation ˆ Operation T URNING ON THE AMPLIFIER The amplifier automatically turns on a few seconds after you turn your vehicle’s ignition switch to ACC or ON or turn on your auto sound system, depending on how you wired the system. The POWER indicator on the side of the amplifier li ghts when the amplifi er is on.
19 Operation ADJUSTING FREQUENCY CROSSOVER If you installed a subwoofer u sing the steps in “Connecting Two Speakers and One Sub- woofer (Unbridged Connecti on)” on Page 14 or “Connecting Two Unbri dged Speakers and One Bridged Subwoofer” o n Page 15, set X-OVER FREQ ON/OFF to ON , then adjust X-OVER FREQ for your vehicle’s acoustics.
20 Troubleshooting ˆ T roubleshooting We do not expect you to have any problems with your Ra dioShack Hi g h P o we r 4/3/2-Channel Bridgeable Amplifier, but if you do h ave a prob lem, this chart mig ht hel p. If not, take the a mpli- fier to your local RadioShack store for assistance .
21 Troubleshooting CARE To enjoy your amplifier for a long time: • Keep the amplifier dry . If it gets wet, wipe it dry immed iately . • Use and store the amplifier only in nor- mal temperature environments. • Handle the amplifier gently and care- fully .
22 Troubleshooting 2. For each fuse, grasp its plastic end and pull it out of the back of the amplifier . 3. If the fuse is blown, replace it. Use only a blade-type fuse wi th the proper rati ng. The fuse must be 30 amps. 4. Grasp the fuse’s plastic end and pu sh it in.
23 Specifications ˆ Specifications Output Power: Stereo ....................................................................... 65 Watts × 4 @ 4 Ohms, 20–20 kHz, 0.5% THD 100 W atts × 4 @ 4 Ohms, 20–20 kHz, 10% T HD 75 W atts × 4 @ 2 Ohms, 20– 20 kHz, 0.
12-2018 05A00 Printed in China RadioShack A Division of Tandy Corporation Fort Worth, Texas 76102 Limited One-Y ear Warranty This product is warranted by RadioShack against manufactu ring defects in m.
Een belangrijk punt na aankoop van elk apparaat Radio Shack XL-400 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Radio Shack XL-400 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Radio Shack XL-400 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Radio Shack XL-400 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Radio Shack XL-400 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Radio Shack XL-400 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Radio Shack XL-400 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Radio Shack XL-400 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
