Gebruiksaanwijzing /service van het product RHP 33 van de fabrikant Raypak
Ga naar pagina of 19
Raypak ® RHP Series Swimming Pool and Spa Heat Pump OWNER and INST ALLA TION MANUAL This manual should be maintained in legible condition and kept adjacent to the heat pump or in a safe place for future use. For additional information call: (03) 9757 3333 Effective Date: Dec 2004 Replaces: All Previous V ersions Part No.
PRODUCT SAFETY SIGNS AND LABELS This manual, as well as the pool/spa heat pump itself, contains product safety signs and labels. Please read these signs and labe ls, as they convey important safety information about hazards that may be potentially present in and around the heat pump.
RHP Series Swimming Pool and Spa Heat Pump OWNER and INST ALLA TION MANUAL CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 I. Installation . . . . . . . .
Intr oduction This pool/sp a heat pump is an electro mechanical machine that incorporates a pressurised refrigerant gas in a sealed system. ONL Y trained and qualified service personnel should attempt to inst all or service this equipment.
• Each side of the unit must be located at least 300mm from walls, pipes, or other obstructions for unrestricted air intake and service access. Do not inst all the unit within 1m of fossil fuel burning heaters.
III. W ater Connections The heat pump inlet and outlet connections are NOT interchangeable. They must be connected as instructed below . 1. Connect the heat pump in the return water line between the pool filter and the pool. See page 10, Plumbing Diagrams.
Indicator Lamps : There are 6 indicator lamps located on the unit control panel: • Power (amber lamp): When lit, indicates power is applied to the unit. • Wa t e r Flow (green lamp): When lit, indicates normal water flow . • Heat Demand (green lamp): When lit, indicates the actual water temperature is below the target water temperature.
NOTE: The heat pump will be OFF when the Remote position is selected on the Po ol/Sp a selector switch. 4.Allow the heat pump to operate for a few minutes to stabilize operating pressures and to allow various component temperatures to normalize.
VIII. Summer Shutdown If you do not plan to use the pool heat pump during the summer months, secure and protect it as follows: 1. From the control panel, turn the control switch to Remote (OFF). 2. T urn the heat pump power switch to OFF. 3. Leave the valves set the way they are unless additional circulation is required.
2. B. Cabinet Care (optional) - The cabinet is designed for outdoor use and requires little care. However , you can clean it if you wish. 1. 2. W ash the cabinet with soap and water .
operation. After the desired temperature is reached, return the system to normal operation. •I s airflow through the unit being obstructed? Restrictions such as shrubbery , tall grass, dirty coils, or any other obstruction to airflow will reduce performance.
POWER SUPPL Y •V erify that all circuit breakers are reset and working properly . •I f t h e Power lamp on the control panel still does not light, contact the installing dealer , since it may be a power problem requiring an electrician. WAT E R F L O W •V erify that the filter is clean to provide good flow .
Plumbing Diagrams For systems with pumps of le ss than 2 HP(1.5Kw) (und er 300 l/min), no external bypass is required. Connections a re 50 mm pipe slip. Plumb the heat pump after the filter and before any chlorinators. Wa t e r I n (from pool or S pa) Wa t e r O u t (to pool or S pa) Filter For systems with pumps of 2 HP (1.
Heat Pump Schematic 12 4 3 A B C D 4 3 2 1 D C B A e l t i T n o i s i v e R r e b m u N e z i S A f o t e e h S 3 0 0 2 - n a J - 7 2 : e t a D : y B n w a r D b d d .
Contr ol Panel Assembly Replacement Parts List 12 4 7 13 11 10 16 11 9 15 2 5 8 14 3 6 1 ITEM QTY DESCRIPTION PART No. 11 Control Panel 21 Contactor Compressor 31 F a n Relay 41 Control Board 24Volt 5.
Contr ol Panel Cover Assembly Replacement Parts List 1 4 4 4 7 6 7 6 8 8 5 Front ITEM QTY DESCRIPTION PART No. 11 Control Panel Cover 22 P O T 31 S w i t ch Type A403 43 K n o b 51 Label Control Panel.
Heat Pump Assembly Replacement Parts List - RHP 3 3 11 15 13 12 5 9 2 9 16 7 7 18 14 6 7 3 17 19 4 10 1 8 Model RHP 33 *See assembly drawing in this manual IT EM QTY DESCRIPTION PART No.
15.
16.
Een belangrijk punt na aankoop van elk apparaat Raypak RHP 33 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Raypak RHP 33 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Raypak RHP 33 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Raypak RHP 33 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Raypak RHP 33 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Raypak RHP 33 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Raypak RHP 33 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Raypak RHP 33 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
