Gebruiksaanwijzing /service van het product 100271-01 van de fabrikant Remington Power Tools
Ga naar pagina of 16
ELECTRIC CHAIN S A W SECTION PAGE Symbol Information ............................................................ 2 Safety Warnings ................................................................. 3 Before Operating Chain Saw ........................
2 100273 INFORMA TION SYMBOLS ! WARNING ICON G 001 Read Instruction Manual Do Not Expose to Rain or Use in Wet Conditions Remove Plug Immediately if Cable is Damaged or Cut Hold Chain Saw with Both Hands Beware of Kickback Hearing and Eye Protection Must Be Worn Safety Information Warnings Appears Throughout This Manual Pay close attention to them.
3 3 100273 BEFORE OPERATING CHAIN SAW 1. Read and understand this owner ’ s manual before operating chain saw. 2. Use chain saw for cutting wood only. Do not use for cutting any non-wood items. 3. Only well-instructed adults should operate chain saw.
4 100273 • Never try cutting through two logs at same time. Only cut one log at a time. • Do not bury guide bar nose or try plunge cut (boring into wood using guide bar nose). • Watch for shifting of wood or other forces that may pinch chain. • Use extreme caution when re-entering a previous cut.
5 5 100273 Front Hand Guard Shield between front handle and guide bar. Protects left hand while using saw. When kickback occurs, the front hand guard is moved forward by the back of operator ’ s left hand. This stops the saw chain quickly, reducing the chance of serious injury.
6 100273 ! WARNING ICON G 001 W ARNING Cutting edges on chain are sharp. Use protective gloves when handling chain. Figure 3 - Assembling Guide Bar, Chain, and Hand Guard Adjusting Block Adjusting Screw Sprocket Support Adjusting Plate Figure 4 - Part Locations for Assembling Guide Bar ASSEMBL Y UNP ACKING 1.
7 7 100273 SAW CHAIN TENSION ADJUSTMENT Note: For pre assembled models, the saw chain tension is properly set at factory. A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Follow steps below to readjust saw chain tension.
8 100273 EXTENSION CORDS Use proper extension cord with this chain saw. Use a HO7RN extension cord no less than 1.5 mm 2 at distances up to 30 meters. Use a ground fault circuit interrupter as part of the power supply system. Use an extension cord heavy enough to carry the current your saw will draw.
9 9 100273 OPERA TING CHAIN SA W Continued TRIMMING A TREE (Pruning) Trimming a tree is the process of cutting limbs from a living tree. Make sure your footing is fi rm. Keep feet apart. Divide your weight evenly on both feet. Follow directions below to trim a tree.
10 100273 OPERA TING CHAIN SA W Continued Figure 14 - Limbing A Tree Limbing is removing branches from a fallen tree. Make sure your footing is fi rm. Keep feet apart. Divide your weight evenly on both feet. Do not remove larger limbs under tree that support log off ground.
11 11 100273 OPERA TING CHAIN SA W Continued 2nd Cut 1st Cut Figure 16 - Bucking Log When Log Is Supported On One End 1st Cut 2nd Cut Figure 17 - Bucking Log When Log Is Supported On Both Ends Log Supported On One End 1. Make fi rst cut on underside of log (see Figure 16).
12 100273 CLEANING SAW BODY Keep saw body clean. Use a soft cloth dampened with a mild soap and water mixture. Wipe saw body to clean. CARE OF GUIDE BAR Uneven bar wear causes most guide bar problems. Incorrect sharpening of chain cutter and depth gauge settings often cause this.
13 13 100273 CLEANING AND MAINTENANCE Continued Sharpening Cutters Use fi le guide for 30 ° fi ling. 1. Adjust chain for proper tension (see Saw Chain Tension Adjustment , page 7). 2. Clamp guide bar in vise to hold saw steady. Note: Do not clamp chain.
14 100273 CLEANING AND MAINTENANCE Continued Replacing Saw Chain Replace chain when cutters are too worn to sharpen or when chain breaks. Only use replacement chain noted in this manual. Always include new drive sprocket when replacing chain. This will maintain proper driving of chain.
15 15 100273 TROUBLESHOOTING OBSERVED FAULT Saw runs, but does not cut. Saw does not cut unless heavily forced. Cutting produces only sawdust with few large chips. Saw runs slow. Saw stalls easily. Motor of saw does not run when you squeeze trigger. Motor of saw runs, but chain does not move.
W ARRANTY INFORMA TION KEEP THIS WARRANTY Always specify model and serial numbers when writing the factory. We reserve the right to amend these speci fi cations at any time without notice. The only warranty applicable is our standard written warranty.
Een belangrijk punt na aankoop van elk apparaat Remington Power Tools 100271-01 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Remington Power Tools 100271-01 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Remington Power Tools 100271-01 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Remington Power Tools 100271-01 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Remington Power Tools 100271-01 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Remington Power Tools 100271-01 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Remington Power Tools 100271-01 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Remington Power Tools 100271-01 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
