Gebruiksaanwijzing /service van het product AS 9075 van de fabrikant Audiovox
Ga naar pagina of 15
Model AS 9075 Installation Manual Remote Start Upgrade Module Installation Instructions This Unit Is Intended For Installation In V ehicles With 12 V olt Negative Ground Electrical Systems, Gasoline or Diesel With T rue T ach Reference And Automatic T ransmissions Only .
The AS-9075 Remote Start/Keyless Entry System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glow plug preheat which may be required for certain diesel vehicles, (see selectable feature #5).
Remote Start Connection WIRING THE 6 PIN MAIN POWER HARNESS: RED w/ WHITE Trace Wire: + 12 volts Battery 1 Source Connect this wire t oa+1 2V D C constant source found at the vehicle's ignition switch using the 30 Amp fuse and holder provided. This wire provides power for the control circuit as well as the ignition 1 and ignition 2 relays.
BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the to the "ON" or "RUN&.
the Black w/ White wire is at open circuit through the control switch, the remote starter is disabled. Connect the Black w/ White tracer wire to one of the wires from the back of the previously mounted control switch. Connect the remaining wire of the control switch to chassis ground.
This wire should be connected to the ignition input of the alarm system. The Yellow w/ Black wire output will allow you to remote start the vehicle while leaving the alarm armed, and to lock/ unlock the doors while running under control of the remote start unit.
NOTE: These wires are typically White w/ Black trace and Violet w/ Y ellow trace, however in later model Cadillacs, they are run through an orange sleeve, and are either both Black, both Y ellow , or both White wires. Consult the factory service manual for additional information.
8 WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote Start unit's operation.
9 NOTE: 1) When selecting Diesel operation, (Feature Five), over gasoline, the only change is to the ignition 1 circuit. When Diesel is selected, the ignition 1 circuit will power up 10 seconds before the start circuit. The intent of this feature is to allow the glow plug warming required by some diesel engines.
10 The parking lights will flash a number of times indicating the reason for the last remote start shutdown. The light flash indications are as follows: 1 Flash 1 0 or 1 5 Minute Run Timer Expired 2 F.
11 TESTING YOUR INST ALLA TION: CAUTION!! The following procedure must be performed after the installation of an Audiovox Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both.
ignition switch side of the Neutral Start Switch. If the vehicle you are working on does not have an Electrical Neutral Safety Switch, i t will be necessary to reconfigure the Remote Starts Wiring to accommodate this vehicle.
margin of safety and will prevent the vehicle with a Mechanical Neutral S tart Switch from starting in gear . AUDIOVOX ADVISES THA T YOU MAINT AIN THE F ACTORY CIRCUIT WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available.
METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A . Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B . Cut this wire and connect the ignition cylinder side to chassis ground. C .
WIRING THE CONTROL MODULE 15 © 1998 Audiovox Corp., Hauppauge, N.Y . 1 1788 Form No. 128-5365A 2nd White.
Een belangrijk punt na aankoop van elk apparaat Audiovox AS 9075 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Audiovox AS 9075 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Audiovox AS 9075 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Audiovox AS 9075 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Audiovox AS 9075 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Audiovox AS 9075 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Audiovox AS 9075 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Audiovox AS 9075 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
