Gebruiksaanwijzing /service van het product R8452 van de fabrikant RIDGID
Ga naar pagina of 24
1 Y our circular saw has been engineered and manufactured to our high standards for dependability , ease of operation, and operator safety . When pr operly cared for , it will give you years of rugged, trouble-free performance.
2 Introduction ....................................................................................................................................................................... 2 General Safety Rules .....................................
3 GENERAL SAFETY RULES WARNING! RE AD AND UN DE RS T AN D ALL INS TR UC TI ON S. Failure to follow all instructions listed below , may r esult in elec tric shoc k, fir e and/or serious persona l injury . SA VE THESE INSTRUCTIONS WORK AREA Keep your work area clean and well lit.
4 SERVICE T ool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury . GENERAL SAFETY RULES When servicing a tool, use only identical replacement parts.
5 SPECIFIC SAFETY RULES Support large panels to minimize the risk of blade pinching and KICKBACK. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.
6 SAFETY RULES FOR CHARGER WARNING! RE AD AND UN DE RS T AN D ALL INS TR UC TI ON S. Failure to follow all instructions listed below , may r esult in elec tric shoc k, fir e and/or serious persona l injury .
7 SYMBOLS Some of the follow ing symbol s may be used on this tool. Please study them and learn their meaning . Pro per interp re tatio n of these symbols will allow you to operate the tool better and safer .
8 SYMBOLS SERVICE Servicing requir es extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair . When servicing, use only identical replacement parts.
9 FEA TURES Fig. 1 PRODUCT SPECIFICA TIONS Blade Diameter ....................................................... 6-1/2 in. Blade Arbor ............................................................... 5/8 in. Cutting Depth at 0º ......................
10 FEA TURES ASSEMBL Y KNOW YOUR CIRCULAR SAW See Figure 1. The safe use of this pr oduct r equires an understanding of the information on the tool and in this operator’ s manual as wel l as a know led ge of the pr ojec t you are atte mpt ing . Bef or e use of this product, familiarize yourself with all operating features and safety rules.
11 A TT ACHING THE BLADE See Figure 2. WARNING: A 6-1/2 in. blade is the maximum blade capacity of the saw . Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guar d, while thicker blades will prevent blade screw from securing blade on spindle.
12 OPERA TION WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict sever e injury . WARNING: Always wear safety goggles or safety glasses with side shields when operating tools.
13 LED FUNCTION OF CHARGER See Figure 5. Fig. 5 POWER INDICA TOR EV ALUA TE INDICA TOR CHARGING INDICA TOR FULL INDICA TOR NOTE: The 9.6 V olt, 12 V olt, and 14.4 V olt battery packs will not slide all the way down onto the char ger port. Insert 9.6 V olt, 12 V olt, and 14.
14 OPERA TION TO INST ALL BA TTER Y P ACK See Figure 6. Place the battery pack in the saw . Align the raised rib inside the saw with the groove on the battery pack. Make sure the latches on each side of the battery pack snap in place and the battery pack is secur ed in the saw before beginning operation.
15 OPERA TION Fig. 8 Fig. 9 KICKBACK See Figures 8 - 11. Kickback occurs when the blade stalls rapidly and the saw is driven back towar ds you. Blade stalling is caused by any action which pinches the blade in the wood. WARNING: T o avoid kickback, release switch immediately if blade binds or saw stalls.
16 OPERA TION LOCK-OFF BUTTON See Figure 12. The l ock- off butto n reduce s th e pos sibil ity o f ac ciden tal starting. The lock-of f button is located on the handle above the switch trigger . The lock-off button must be depressed before you pull the switch trigger .
17 OPERA TING THE SAW See Figures 14 - 15. It is important to understand the correct method for oper - ating the saw . Refer to the figures in this section to learn the correct and incorr ect ways for handling the saw .
18 OPERA TION Fig. 16 CROSS CUTTING/RIP CUTTING See Figures 16 - 17. When making a cross cut or rip cut, align your line of cut with the outer blade guide notch on the saw base.
19 OPERA TION Fig. 19 BASE ASSEMBL Y WIDTH OF CUT SCALE BLADE WIDTH OF CUT SCALE See Figure 19. A width of cut scale has been provided on the base of the saw . When making straight cr oss cuts or rip cuts, the scale can be used to measure up to four inches to the right side of the blade.
20 POSITIVE 0° BEVEL STOP See Figure 22. The saw has a positive 0° bevel stop that has been factory adjusted to assure 0° angle of the saw blade when making 90° cuts.
21 5 0 4 5 3 0 3 2 1 4 5 0 0 1 2 3 4 5 6 Fig. 23 LOWER BLADE GUARD HANDLE LOWER BLADE GUARD POCKET CUTTING See Figure 23. WARNING: Always adjust bevel setting to zero before making a pocket cut. Attempti ng a pocket cut at any other setting can result in loss of control of the saw , possibly causing serious injury .
22 MAINTENANCE WARNING: When servicing use only identical RIDGID replacement parts. Use of any other parts may create a hazar d or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust.
23 W ARRANTY Proof of purchase must be presented when requesting war - ranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after . This product is manufactured by One W orld T echnologies, Inc. The trademark is licensed from RIDGID, Inc.
24 983000-898 3-24-06 (REV :02) Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center . Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www .
Een belangrijk punt na aankoop van elk apparaat RIDGID R8452 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen RIDGID R8452 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens RIDGID R8452 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding RIDGID R8452 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over RIDGID R8452 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van RIDGID R8452 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de RIDGID R8452 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met RIDGID R8452 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
