Gebruiksaanwijzing /service van het product 10H van de fabrikant RJTech
Ga naar pagina of 34
RJ MOBILITY L TD . BARRETT 7H & 10H TECHNICAL MANU AL This T echnical Manual will ensure that the wheelchair is maintained to the required standard and is f or use b y trained personnel only .
This T echnical Manual contains impor tant information regarding maintenance of the Barrett F oldaw ay Wheelchair thus ensuring its saf e operation. Please make sure that y ou understand all instructions thoroughly . It is recommended that maintenance is under taken at six monthly inter v als f or a wheelchair that is in constant daily use.
CONTENTS SECTION 1 USER CA TEGORIES 2 SPECIFICA TIONS 3 WHEELCHAIR DIA GRAM 4 MAINTENANCE CHECKS 5 T OOL REQUIREMENTS 6 UPHOLSTER Y 7 ARMRESTS 8 FOO TRESTS 9 BRAKES 10 PUSH HANDLES 11 LOCKING LINKS AN.
SECTION 1: USER CA TEGORIES 1.1 USER CA TEGORIES FOR THE B ARRETT FOLD A W A Y MODEL 7H SELF-PR OPELLING WHEELCHAIR A1. Occupant with all limbs intact and having the ability to co-ordinate both arms and hands with sufficient strength to self-propel and control the wheelchair saf ely and maintain an upright seating position.
1. Ov erall length 2. Ov erall width 3. F olded length 4. F olded width 5. F olded height 6. Maximum weight 7. W eight less ar mrest and f ootrests 8. Seat plane angle 9. Seat widths av ailab le 10. Seat depths a vailab le 11. Seat height at front 12.
SECTION 3: WHEELCHAIR DIA GRAM 3.1 B ARRETT FOLD A W A Y MODEL 7H WHEELCHAIR 3.2 B ARRETT FOLD A W A Y MODEL 10H WHEELCHAIR PUSH HANDLE BRAKE LEVER BACKREST RELEASE KNOB REAR WHEEL HANDRIM FRONT CAST .
SECTION 4: MAINTENANCE CHECKS 4.1 Open the wheelchair , all mov ements should be free throughout the folding r ange. 4.1.1 Examine the seat and backrest f abr ics f or wear , damage or staining. Examine retaining screws f or tightness and general condition.
SECTION 5: T OOL REQUIREMENTS Spanners: 15/16 inch or 24mm AF Castors (See Section 12) 5/16 inch Whitwor th Legrest clamp (See Section 8) 10mm AF Heel Loop (See Section 8) 19mm AF Wheel nuts (See Sect.
SECTION 6: UPHOLSTER Y 6.1 Diagram 6.2 P ar ts List RJ No Seat F abr ic Ninian Ambla 15 x 17 inch 38cm x 43cm SF61 Ninian Ambla 17 x 17 inch 43cm x 43cm SF63 Backrest F abric Ninian Amb la 15 x 17 inch 38cm x 43cm SF62 Ninian Ambla 17 x 17 inch 43cm x 43cm SF64 M5 x 20 long, raised countersunk scre w F102 No .
6.3 Inspection F abr ic: Check f or staining, wear , tear and stitching. Check n ut inser ts in frame f or secur ity and stripped threads. Check securing scre ws for bending and stripped threads and burrs . Cushions (if fitted): Check cushions f or staining, wear , tear and stitching.
SECTION 7: ARMRESTS 7.1.1 Diagram (Non-Domestic) 7.1.2 P ar ts List (Non-Domestic) RJ No Ar mrest Assemb ly complete - Left SP402 - Right SP403 Ar mrest P ad Blac k M170 No .
7.2.1 Diagram (Domestic) 7.2.2 P ar ts List (Domestic) RJ No Ar mrest Assemb ly complete - Left SP364L - Right SP364R Ar mrest P ad Blac k M41 M6 x 30 Raised CSK P ozi Machine screw zinc plated 0755 A.
7.3 Inspection Check armpad f or excess w ear or damage. Check armpad is secured to frame. Check side panel is not damaged. Ensure ar mrest locates in rear brac ket on push handle when fitted to wheelchair .
SECTION 8: FOO TREST 8.1 Diagram 8.2 P ar ts List RJ No F ootrest Hanger with retaining - Right SP406 clamp assembly M102 - Left SP407 Retaining Clamp Assembly M102 5/16 x 1 1/4 Inch Bolt, zinc plated.
8.3 Inspection Check that f ootrest assembly loc ks into position forw ard and backw ard. Apply light grease to s wiv elling end. Ensure that stem clamp holds f ootplate in position. Ensure that f ootplate will remain in ver tical position when required.
SECTION 9: BRAKES 9.1 Diagram 9.2 P ar ts List RJ No Brak e Assembly complete - Left SP203L - Right SP203R Spring - Left SF233L - Right SF233R Brak e Shoe SF174 1/16 x 1/2 inch Split Pin F50 No .
9.3 Inspection Check ball knob f or secur ity . Check le vers f or distor tion. Check br azed joints f or crac ks. Check piv ot shafts f or distor tion. Replace piv ot bolts if necessar y due to excessiv e wear . Ensure no oil/grease on brak e pad. 9.
SECTION 10: PUSH HANDLES 10.1 Diagram 10.2 P ar ts List RJ No Push Handle Assembly complete with handgrip , pivot bolt - Left SP404 - Right SP405 M6 x 45 he x head bolt zinc plated F11 M6 self locking.
10.3 Inspection Check each push handle f or evidence of bending. Check each push handle f or evidence of cr acking through nutser t holes. Check handg r ip is secure. Check f or free mov ement of plunger . Lubr icate with light oil. Check that plunger locates in the hole at rear of the side fr ame.
SECTION 11: CR OSSBRA CE ASSEMBL Y 11.1 Diagram P age 1 of 3 M6 LOCKNUT P80 M6 LOCKNUT P80 1/4 NYLON W ASHER F86 1/4 NYLON W ASHER F86 M6 x 25 HEX HEAD SET SCREW ZINC PLA TED F124 M6 LOCKNUT P80 1/4 N.
11.3 Inspection Check Cross Br aces for bending and e vidence of cracks around piv ot holes. Check each tab on the sidefr ames for e vidence of bending, elongation or wor n holes, and cr acks in brazing or tubing. 11.4 Cross Brace Assemb ly Remo val Remov e the two 1/4 UNF set scre ws secur ing the Cross Brace Assemb ly to each sideframe.
11.7 P ar ts List RJ No Locking Link Assemb ly 17" complete with f asteners SP207 Locking Link Assemb ly 15" complete with f asteners SP208 M6 X 25 he x head set screw , zinc plated F125 M6 self-locking thin n ut, zinc plated F130 1/4 Diameter Nylon plain washer F86 11.
SECTION 12: CAST ORS 12.1 Diagram 12.2 P ar ts List RJ No 190mm narrow profile MCP M19B 190mm wide profile MCP M171 12.3 Inspection Check f or excessiv e wear in cro wn bear ings and wheel spindle. Replace castor if necessary . Check condition of stud which scre ws into frame .
SECTION 13: WHEELS 13.1 Diagram 13.2 P ar ts List RJ No 315mm (12 1/2") plastic spoked wheel with axle and puncture proof tyre M194 46cm ( 18") diameter spoked wheel with axle , pneumatic ty.
13.5 Wheel Fitting Hold the he xagon section of the axle between the wheel and the wheelchair frame . Apply LOCTITE Thread Locking Compound Gr ade 241 to the M12 Thread and tighten the M12 nut to a torque of 30 to 35 lbs/ft (40 to 47 Nm) to secure the wheel to the wheelchair .
SECTION 14: QUICK RELEASE WHEEL 14.1 Diagram 14.2 P ar ts Lists RJ No 50cm (20") diameter detachable wheel with spindle WH20BKAL TTT 50cm (20") diameter pneumatic tyre 20TYR 50cm (20") .
14.4 Wheel Remov al Ensure the brak e is not applied. With one hand hold the frame of the wheelchair and with the other hand hold the spokes surrounding the hub and fully depress the centre b utton pulling the wheel aw a y from the wheelchair axle bush and releasing the centre b utton.
SECTION 15: ELEV A TING LEGREST 15.1 Diagram 15.2 P ar ts List RJ No Legrest Assemb ly Complete - Left SP333L - Right SP333R Legrest T rigger Spr ing SF234 Ele vating Rod SF123 Legrest T rigger SF122 .
15.3 Inspection Check heel loop f or secur ity . Nuts should be tightened to 10 lbs/ft (13 Nm). Check piv ot bolt f or wear . Check calf pad f or wear/damage.
SECTION 16: ARMREST OUTRIGGERS 16.1 Diagram 16.2 P ar ts List RJ No Ar mrest Soc ket Extension Assemb ly SF307 Ar mrest Outrigger T ab SF305 M6 x 65 Bolt zinc plated F144 M6 Nut zinc plated P80 2BA x 3/8 P ozi P an Machine Screw zinc plated F145 16.3 Inspection Check f or damage to sock ets.
SECTION 17: RECLINING B A CKREST 17.1 Diagram 17.2 P ar ts List RJ No Backrest T ube Assembly complete G104 Handle G142 Ratchet pull rod - Left G144L - Right G144R Spring G141ND Ratchet Plate G140 Wing Nut 6mm chrome F58 No .
17.3 Inspection Check quadr ant for distortion wear and cracks . Check quadr ant peg for bending and w or n threads. Check pull release bars f or bending. 17.4 Reclining Bac krest Dismantling Release wingnuts on quadrant br ack ets. Release bolts securing backrest tubes to wheelchair side frames .
SECTION 18: DET A CHABLE TRA Y 18.1 Diagram 18.2 P ar ts List GWD No RJ No T ra y Brack et - left SF316L - right SF316R T ra y 837 T ra y Brack et 838 18.3 Inspection Check f or damage to the tra y , par ticularly for w ooden splinters. Check security of attachment scre w ‘B’ and check tra y attachment scre ws for security .
TECHNICAL MANU AL AMENDMENT RECORD ISSUE SECTION D A TE AMENDED COMMENTS.
Een belangrijk punt na aankoop van elk apparaat RJTech 10H (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen RJTech 10H heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens RJTech 10H vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding RJTech 10H leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over RJTech 10H krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van RJTech 10H bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de RJTech 10H kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met RJTech 10H . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
