Gebruiksaanwijzing /service van het product LCM5043NP van de fabrikant Audiovox
Ga naar pagina of 20
LCM5043NP & LCM5643NP Remote Controlled Color Display Monitor with Headphone Jack Installation and Owner's Manual EL E C T R O N I C S C O R P .
1 EXPLANA TION OF GRAPHIC SYMBOLS W ARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: 1. This product is designed to operate with a 12 volt, negative ground bat- tery system. 2. Disconnect the ground wire from the battery terminal before connecting the electrical system.
2 SYSTEM OVERVIEW The LCM5043NP is comprised of a 5" Thin Film Transistor (TFT) Liq- uid Crystal Display ( LCD) Monitor . The LCM5643NP is comprised of a 5.
MA TERIALS LIST 1. System Monitor (LCM5043NP=136C2187) or (LCM5643NP=136C2186) (1pc.) 2. Remote Control Unit (136B2156) with Lithium Battery , 3V ,CR 2025 (1pc.) 3. Interconnect Box (136B2183) (1pc.) 4. Monitor Cable, 8' (1 12B3152) (1pc.) 5. Headrest Mounting Tray (LCM5043NP=102C3740) or (LCM5643NP=102C3742) (1pc.
VEHICLE PREP ARA TION 1 ) Decide on the system configuration and the options that will be in- stalled (i.e. what components, VCP , DVD, TV T uner , Video Game, Monitor , FM Modulator , etc.). 2 ) Read the manuals and get familiar with the electrical requirements and connections.
5 10 ) After verifying the proper operation of the system, proceed to mount each component. 1 1 ) The mounting method, and the location will vary from vehicle to vehicle, so this manual will only focu.
6 3 ) Adjust viewing angle of monitor by tightening the fastener at the side. 4 ) When the system components are mounted, test the system to verify that it is functioning correctly . Make sure that no wiring was pinched, or connected improperly during the final installation.
7 1 ) Remove the headrest from the vehicle for easiest installation. 2 ) Lay headrest on a flat surface. 3 ) Center trim collar on headrest as shown. NOTE: Depending on the angle of the headrest the Trim Ring and housing may be mounted upside down. 4) Using a Permanent Marker , mark headrest material along the interior of the Trim Ring.
9 ) Using your fingers, tear the foam out of the headrest leaving a re- cess where the shell will be in- serted. NOTE: At this point you will need to install the harness up through the area into the recess. It may be helpful to follow one of the posts and tie wrap it to the post for restraint.
1 1 ) Guide the cable through the side opening of the Mounting Tray and plug it into the Monitor . Make sure the connector locks into place. Insert the Monitor into the Mounting Tray and secure the cable using tie wraps or screws 1 2) Turn the Monitor around and in- sert it into the Mounting Tray housing.
ELECTRICAL CONNECTION (Wiring Diagram) 10 Video Source Input (1&2) Not Used A V Output.
The following procedure is to remove the Monitor from the Mounting T ray using the supplied Removal T ool. NOTE: Use care when per- forming this procedure not to scratch any exposed surfaces with the edges of the Removal T ool. Masking tape applied to the two tips or legs of the Removal T ool will help prevent scratching.
CONTROLS AND INDICA TORS Headphone OPERA TION 1. Press power On/Off button to the On position. The LED power indicator will light red. 2. Press the Picture Select button to adjust the picture display characteristics. The adjustments will be shown on the On Screen Display in the following sequence: Contrast, Brightness, Color , and TINT .
MAINTENANCE T o avoid electrical shock, do not open the enclosure. High voltage is present. No user serviceable parts inside the enclosure. Do not use any chemical solvent, cleaning agent or corrosive de- tergent to clean away dirt on the surface of the screen.
REMOTE CONTROLLER NOTE : The Remote Controller supplied with this system is a stan- dard remote control, which is used to operate other systems. The Remote Controller is not a universal remote and will only perform the functions described herein. Only the Keys highlighted on the Remote Controller image bellow are used to operate this system.
15 MENU FUNCTION KEY : The MENU Key is used to navigate between the Color , Brightness and Tint adjustment modes. When the MENU Key is pressed an On Screen Display(OSD) will appear as shown bellow . OSD Press release and tap the MENU Key until the desired adjustment mode is selected.
16 NOTE: For the LCM5643NP - Select either * NTSC or P AL, press the p or q Keys ( CH/DISK/SET ). VOLUME CONTROL KEY : T o switch between Video Input Sources (A V1 and A V2) press and release the MODE Key . VIDEO SOURCE MODE KEY : T o increase or decrease the V olume, press and hold the VOL p or q Key until the desired volume is reached.
17 Replacement of Remote Controller Battery: 1. Use a small coin to pry open battery holder from compartment. 2. Remove old battery and put in a new one with positive sign “ + “ facing upward. 3. Push compartment into position. Precaution: 1. Dispose off used battery properly .
18 LCM5043NP: LCD Panel Size (Diagonal) ................................... 5 " LCD Panel Format ................................................. 960 x 234 dots LCD Panel Resolution ........................................... 224,640 pixels LCD Backlight Life .
© 2002 Audiovox Electronics Corp., Hauppauge, NY 128-6323 AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part there.
Een belangrijk punt na aankoop van elk apparaat Audiovox LCM5043NP (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Audiovox LCM5043NP heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Audiovox LCM5043NP vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Audiovox LCM5043NP leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Audiovox LCM5043NP krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Audiovox LCM5043NP bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Audiovox LCM5043NP kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Audiovox LCM5043NP . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
