Gebruiksaanwijzing /service van het product Radio Modems van de fabrikant RTcom
Ga naar pagina of 18
User Manual RTcom-Universal, Global Max and Outback Radio Modems Copyright Radio-Tech Limited 1998-2000.
2 CONTENTS INTRODCUTION 3 Selecting the frequency of operation 5 R.F Path Surveys 5 INSTALLATION Power Supplies 6 Location 6 Antenna Feeders 7 Lightning Surge Protection 8 Antenna Installation 9 Anten.
3 INTRODUCTION The RTcom-range of radio modem is intended as a direct replacement for cables over short, medium and long distance, serial data links. They are suitable for part of point-to-point, master to slave or scanning telemetry links, where the modem is either used on its own our in conjunction with existing cables.
4 In many countries it is quite legal to operate systems without need for operating licences. These countries include the United Kingdom, Australia, New Zealand, Korea, South Africa, Scandinavia and the majority of Europe.
5 Frequency of operation Often there is not a choice over operating frequency. In most countries frequency allocations are very limited, by way of example in Europe there is only 433-435MHz UHF or 868-870MHz SHF. While the UK and many others offer VHF, UHF and SHF allocations.
6 If there is doubt over the signal reaching the receiver a path survey should be conducted. The outback modem includes a test mode that places the modems transmitter into constant transmit mode. This permits the measurement of signal strength at the receiver.
7 For battery powered operation in cold and damp climates the only reliable way to achieve long term operation is to use double IP65/7 enclosures, with both the outer and inner enclosure fitted with silica gel desiccant sachets. Please be aware that solar heating and wind chill can take the modem beyond its designed operating temperature range.
8 Lightning Surge Protection: A direct lightning strike can never be totally protected against or predicted. Currents exceeding 10,000A can flow vaporising antenna, feeders, towers and other such structures. Lightning conductors will give a degree of protection to the building but not always to the electronic apparatus within.
9 Antenna Installation The type and location of the antenna used can have a profound effect on your overall system performance and its legality. In point to point links it is good practice to make efficient use of the radio spectrum by selecting an antenna that will project the R.
10 Warning : The use of gain antenna in some countries is not permitted. Similarly where ERP (transmitted power limits) are imposed the actual transmitted power must not exceed the limit stated. This means that the transmitter output power, less any coaxial feeder losses, plus the antenna gain must not exceed the specified maximum ERP.
11 Guide to your RTcom-Global & Max Modem Status LED's 12-24V dc supply RS422 & RS485 Interface RS232 interface Links to select 2-4 wire RS485 Mode Switch for Data Rate and data format Ch.
12 Guide to your RTcom-Outback Guide to your RTcom-Max (Please take care when opening cover) Optional Location for Battery Solar/12-24V dc supply RS422 & RS485 Interface RS232 interface Links to s.
13 CONNECTIONS Data connections should always be made using screened cable. This will insure maximum rejection of interference from outside sources. Always use a common ground point. The RTcom Global, Eurpoa, MAX and Outback modems support RS232, RS422 and RS485 communications, both 2 and 4-wire.
14 Pin Number Designation WRT Modem Notes 1 DCD Optional not normally needed 2 RX (data) RS232 input data to modem 3 TX(data) RS232 output data from modem 4 RTS Optional not normally needed 5 GND Ground 6 B RX(-) RS485/RS422 7 A RX(+) " 8 +Vs Supply 7.
15 On the Global and Max modems two dip switches are provided for the selection of the desired operating mode and two plug links are provided from the selection of 2 or 4 wire RS485 operation. A further DIP switch is provided on the Global modem for frequency Channel selection.
16 OPERATION The RTcom protocol permits 100% transparent operation and direct cable emulation. Simply what goes in comes out! R.F. packet framing, code balancing, encryption and preambles etc are taken care of automatically within the modem.
17 COMMISSIONING The data rate, parity and number of data bits are set using the dual in line switch located above. If a scanner is available the chosen channels and the adjacent channels should be scanned for activity.
18 system. This results in the messages becoming fragmented, thus confusing the modem into thinking the end of file has been detected. The other common problem, in particular with WindowsTM Hyper Terminal, is the way in which is deals with errors.
Een belangrijk punt na aankoop van elk apparaat RTcom Radio Modems (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen RTcom Radio Modems heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens RTcom Radio Modems vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding RTcom Radio Modems leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over RTcom Radio Modems krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van RTcom Radio Modems bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de RTcom Radio Modems kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met RTcom Radio Modems . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
