Gebruiksaanwijzing /service van het product 98BDF van de fabrikant Samsung
Ga naar pagina of 51
SAMTRON 96BDF/98BDF.
Main > Index Main Page On-Screen Display Safety Instructions Troubleshooting Notational Check List Power Q & A Installation Self-Test Feature Check Cleaning Other Introduction Specifications Un.
Main > Safety Instructions > Notational Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.
Main > Safety Instructions > Power Notational Power Installation Clean Other When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode.
Main > Safety Instructions > Installation Notational Power Installation Clean Other Do not cover the vents on the monitor cabinet. z Bad ventilation may cause a breakdown or fire. Put your monitor in a location with low humidity and a minimum of dust.
Main > Safety Instructions > Clean Notational Power Installation Clean Other When cleaning the monitor case or the surface of the CRT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent.
Main > Safety Instructions > Other Notational Power Installation Clean Other Do not remove cover(or back). No user serviceable parts inside. z This may cause an electric shock or a fire.
Keep the monitor away from any magnetic substances. z This may cause discoloring or distortion of the image..
Unpacking Front Rear Bottom Monitor and Stand (Some models include a stand attached. ) Please make sure the following items are included with your monitor.
Unpacking Front Rear Bottom 1. Exit button Use this button to Exit the active menu or the OSD. 2,3. Adjust buttons These buttons allow you to highlight and adjust items in the menu. 4. Menu button Use this button to open the OSD and activate a highlighted menu item.
Unpacking Front Rear Bottom (The configuration at the back of the monitor may vary from product to product.) 1. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 2. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card.
Unpacking Front Rear Bottom 1. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 2. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 3. Tilt/Swivel Base You can separate the base from the monitor.
Connecting Your Monitor Installing the Monitor Driver Base Installation 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the video port on your computer, video board, video card, or graphics card.
Connecting Your Monitor Installing the Monitor Driver Base Installation Automatic Manual When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another.
4. Click the " Install " button in the " Warning " window. 5. If you can see following "Message" window, then click the "Continue Anyway" button.
Connecting Your Monitor Installing the Monitor Driver Base Installation Automatic Manual Windows XP | Windows 2000 | Windows Me | Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor.
6. Select " Don't search ,I will.. " then click " Next " and then click " Have disk ". 7. Click the " Browse " button then choose A:(D:Driver) and choose your monitor model in the model list and click the " Next " button.
10. Monitor driver installation is completed. Microsoft ® Windows ® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose " OK " button on the " Insert disk " window.
Microsoft ® Windows ® NT Operating System 1. Click Start , Settings , Control Panel , and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes . 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK .
Connecting Your Monitor Installing the Monitor Driver Base Installation Tilt/Swivel Base | Attaching and Removing the Base With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle. Note: The base is detachable.
Attaching the Base 1. Place the monitor upside-down on a flat work surface. 2. Align the tabs on the base with the corresponding slots on the bottom of the monitor.
On Screen Display (OSD) Menu System 1 E x it b u tt on: U se thi s b u tt on t o E x it th e ac ti ve menu or th e OSD. 2,3 Adjust buttons: These buttons allow you to highlight and adjust items in the menu. 4 Menu button: Use this button to open the OSD and activate a highlighted menu item.
On Screen Display (OSD) Menu System With the menu off, push the menu button. Push the - button or + button until the Brightness screen is displayed. Push the menu button to open the Brightness adjustment screen. Use the + button to increase the brightness or - button to decrease the brightness.
On Screen Display (OSD) Menu System Follow these instructions to change the Position of the monitor ’ s entire display . With the menu off, push the menu button. Push the - button or + button until the H-Position screen is displayed. Push the menu button to open the H-Position adjustment screen.
On Screen Display (OSD) Menu System Follow these instructions to change the Size of the monitor ’ s entire display . Menu How to adjust H-Size Follow these instructions to change the Size of the monitor ’ s entire display . V -Size With the menu off, push the menu button.
On Screen Display (OSD) Menu System Menu How to adjust Adjust the pincushion setting when the sides of the display are bowed in or bowed out Pincushion With the menu off, push the menu button. Push the - button or + button until the Pincushion screen is displayed.
Adjust the rotation setting when the entire display is tilted left or right. Rotation On Screen Display (OSD) Menu System Menu How to adjust Adjust the parallelogram setting when the display is leaning left or right. Parallelogram With the menu off, push the menu button.
On Screen Display (OSD) Menu System Menu How to adjust Adjust the pinbalance setting when the sides of the display are bowed towards the left or right. Pinbalance Adjust the linearity setting when the display image is compressed at the left, right or top, bottom.
On Screen Display (OSD) Menu System Menu How to adjust Language With the menu off, push the menu button. Push the - button or + button until the Language screen is displayed. Push the menu button to open the Language selection screen. Use the - button or + button to select the language you would like to use.
On Screen Display (OSD) Menu System A “Moiré” pattern can appear on your screen, looking like a series of concentric circles or arcs. T o eliminate this pattern, use the clear moiré adjustments. Menu How to adjust H-Moire With the menu off, push the menu button.
On Screen Display (OSD) Menu System Menu How to adjust Some video cards use video signals higher than 1.0V which causes the display to be very bright. For those video cards, use this feature to select the 1.0V Level. Video Input Level With the menu off, push the menu button.
On Screen Display (OSD) Menu System Menu How to adjust Follow these instructions to get a close-up or a longshot view of the monitor ’ s viewing area. Zoom With the menu off, push the menu button. Push the - button or + button until the Zoom screen is displayed.
Note The monitor may buzz momentarily, the image colors may change and the image will jiggle for a few seconds. These effects are normal. On Screen Display (OSD) Menu System The Degauss feature will remove color impurities caused by magnetic fields.
On Screen Display (OSD) Menu System Menu How to adjust The information on this screen shows Display Timing , User Timing and Factory T iming. Display Timing With the menu off, push the menu button. Push the - button or + button until the Display Timing screen is displayed.
Check List Q & A Self-Test Feature Check Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your dealer .
The screen shows strange colors or just black and white. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection.
Check List Q & A Self-Test Feature Check Question Answer How can I change the frequency? Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.
Main > Troubleshooting > Self-Test Feature Check Check List Q & A Self-Test Feature Check Self-Test Feature Check | Warning Messages | Environment | Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.
1 . If th ere are any woo f er spea k ers near th e mon it or, unp l ug an d re l oca t e th e woo f er t o ano th er room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor.
General PowerSaver Preset Timing Modes General Model Name SAMTRON 96BDF Picture Tube Type 19"(48cm) DynaFlat (45.8cm viewable) Deflection angle 90 ° Dot Pitch 0.26mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix.
General PowerSaver Preset Timing Modes General Model Name SAMTRON 9 8 BDF Picture Tube Type 19"(48cm) DynaFlat (45.8cm viewable) Deflection angle 90 ° Dot Pitch 0.26mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix.
General PowerSaver Preset Timing Modes This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time.
General PowerSaver Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on.
Service Terms Regulatory Authority SAMTRON SEOUL 15TH FL, JOONGANG DAILY NEWS BLDG. 7, SOONHWA-DONG,CHUNG-KU, SEOUL, KOREA, 100-759 TEL : (82-2) 727-3114 SAMTRON U.
Information > Terms Service Terms Regulatory Authority Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'.
Main > Information > Regulatory Service Terms Regulatory Authority FCC Information | IC Compliance Notice | MPR II Compliance | European Notice (Europe only) | PCT Notice | VCCI | TCO'95-Ec.
MPR II Compliance This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. European Notice (Europe only) Products with the CE Marking comply with both the EMC Directive (89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
There are also other characteristics of a monitor, such as energy consumption levels, that are important from both the working and natural environment viewpoints. Since all types of conventional electricity generation have a negative effect on the environment (acidic and climate- influencing emissions, radioactive waste, etc.
CFCs (freons) CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on Earth of ultraviolet light with consequent increased risks of skin cancer (malignant melanoma).
Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances.
Service Terms Regulatory Authority Information in this document is subject to change without notice. © 2002 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co.
Een belangrijk punt na aankoop van elk apparaat Samsung 98BDF (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Samsung 98BDF heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Samsung 98BDF vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Samsung 98BDF leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Samsung 98BDF krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Samsung 98BDF bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Samsung 98BDF kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Samsung 98BDF . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
