Gebruiksaanwijzing /service van het product 42LM4RTC van de fabrikant Sanyo
Ga naar pagina of 19
Interactive Touchscreen User Guide For serial Interface For use with models: 42LM4WPTC 42LM5WPTC 42LM4RTC 42LM5RTC Version 1.3 September 2007 Interactive Touchscreen User Guide.
2.
3 TABLE OF CONTENTS ABOUT THIS MANUAL .................... ....................... ....................... ....................... ...................... ......... 4 CONTACT IN FORMATION ................... ....................... ....................
4 ABOUT THIS MANUAL This manual is intended a s a reference guide for the Interactiv e Touchscreen running under Windows XP™ or Windows Vista™. This User Manual provides the in formation needed to set up the tou chscreen. In addition, this manual describes basic tech nical information about the touchscreen and troubleshooting.
5 INTRODUCTION This manual will explain the wor kings and setup of the touchscreen fitted to your display. An explanation of the monito r and its workings is covered in the Monitor Man ual that came with this product.
6 INSTALLATION LOADING THE TOUCH DRIVER SOFTW ARE ONTO PC 1. Switch on monitor Do not plug the touchscreen interface cable into y our computer . 2. Insert the ‘ Information & Touc h Software installation CD’ into the PC and follow the automatic installation in structions.
7 STARTING THE DRIVER CONTROL PROGRAM Connect the touchscreen ca ble to a free serial port of the. 1. If the Touchscreen con trol panel is not already running, start the dr iver by clicking the icon on the desktop or select the Window s™ START button and RUN "Ma 7_Control_En.
8 Fig 2 EXPLANATION OF THE STATUS SECTION 1. The following explanation of the Status section assumes that the to uchscreen is physically attached to a serial port of the PC: Open - will go red and remai n red only when the driver is pre sent, the correct port is chosen and the Baud rate is set corre ctly.
9 The mouse pointer will not respond to a touch until it has been enabled in the Output section of the Cont rol Program. Details of this will fo llow later in this manual. The Reset button load s fresh data from the touchscreen. This is used as a reference for detecting any new touches.
10 ADJUSTING THE TOUCH SENSITIVITY LEVEL Automatic Setup When you receive your unit, the sensitivity settings will have been optimised when the unit was manufactured. These settings sh ould only be altered if you are experiencing problems such as an electrically noisy environment.
11 7. The moving indicator under Finger Pressure shows the strength of touchscreens signal. Nominally the Coarse Sens itivity slider is adjusted so the Finger Pressure indicator move s about a third of the way along in response to a light touch.
12 CALIBRATION 1. Select the Calib tab as shown below (Fig 5), click the 'Start Calibrat ion' box. Fig 5 2. You will see the following screen (Fig 6); there are three targets to tou ch in total, like the one shown below: Fig 6 3. When each of these targets is disp layed, touch and hold your finger on the centre of the circular target.
13 SETTING THE TOUCH OUTPUT TO SUIT THE APPLICATION PROGRAM 1. Select the Output tab. Fig 7 2. Select the mouse contro l required for your application (Fig 7). To enable the touc h function on the screen, tick the E nable check box. 3. No action selects no mouse pointer movement or button pressing when touching the touchscreen.
14 You must now save the settings Fig 8 1. (Fig 8) Click on file. 2. Click on save to save the curr ent settings. When the touchscreen driv er has been set up and there is no requirement to change it.
15 DIAGNOSTICS AND FREQUENTLY ASKED QUESTIONS Testing the Hardware with ‘Graph’ 1. Select the Graph tab. Fig 9 2. Run a finger around the sen sor, the effect of the finger on nearby wires can be seen by a visible movement on the indicators (Fig 9), each representing one wire.
16 MONITOR MODE Fig 10 1. This section is used to check the output of the touchscreen over the whole display area represented by the wh ite box in the centre. It is useful in checking for an y dead areas on the touchscreen and the performance of the touchscreen being able to follow the finger accurately and responsib ly (Fig 10).
17 USING EDGE ENHANCEMENT 1. To allow easy access to the slider s and buttons at the edge of the displa y, the cursor can be positioned nearer the edge of the screen.
18 FAULT FINDING GUIDE The following are some possible re asons why the touch screen might no t work. If they do not solve your problem or you have a situation not covered please con tact your supplier. DRIVER DOES NOT SEE THE T OUCHSCREEN Touchscreen on a different comm p ort than the one selected.
19 There are several ways to imp rove system performance. Optimise the Background perfor mance against the Applications, to do this follow the simple instructions below: Select the Windows™ STAR T Button; go into Settings and Con trol Panel. Open the System folde r and select the Advance tab.
Een belangrijk punt na aankoop van elk apparaat Sanyo 42LM4RTC (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sanyo 42LM4RTC heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sanyo 42LM4RTC vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sanyo 42LM4RTC leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sanyo 42LM4RTC krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sanyo 42LM4RTC bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sanyo 42LM4RTC kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sanyo 42LM4RTC . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
