Gebruiksaanwijzing /service van het product PLC-XM80L van de fabrikant Sanyo
Ga naar pagina of 89
Owner ’ s Manual ◊ Projection lens is optional. Multimedia Projector MODEL PLC-XM80 PLC-XM80L ◊ Network Supported Refer to the Owner's Manual below for details about network function.
2 This Multimedia Projector is designed with most advanced technology for portability , durability , and ease of use. This projector utilizes built-in multimedia features, a palette of 1.07 billion colors, and matrix liquid crystal display (LCD) technology .
3 T able of Contents Features and Design ............... 2 T able of Contents .................. 3 T o The Owner ..................... 4 Safety Instructions ................. 5 Air Circulation 6 Installing the Projector in Proper Directions 7 Moving the Projector 8 Cautions in Handling the Projector 8 Compliance .
4 Safety Precaution W ARNING: l THIS APP ARA TUS MUST BE EARTHED. l TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. – This projector produces intense light from the projection lens. Do not stare directly into the lens, otherwise eye damage could result.
5 All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners.
6 Openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. CAUTION Hot air is exhausted from the exhaust vent. When using or installing the projector , the following precautions should be taken.
7 Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture in upward, downward, or inclined position in perpendicular direction to the horizontal plane.
8 Use the handle grip when moving the projector . Retract the adjustable feet to prevent damage to the lens and cabinet when carrying. When this projector is not in use for an extended period, put it into a suitable case to protect the projector .
9 AC Power Cord for the United Kingdom: This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an AST A approved BS 1362 fuse must be used of the same rating, marked thus ASA .
10 Part Names and Functions CAUTION Hot air is exhausted from the exhaust vent. Do not put heat-sensitive objects near this side. ⑪ Infrared Remote Receiver (Back) ⑫ T erminals and Connectors ⑬ .
11 ⑦ R/C jACK When using the wired remote control, connect the wired remote control to this jack with a remote control cable (not supplied) (p.15). ⑮ USB CONNECTOR (Series B) Use this connector when controlling a computer with the remote control of the projector .
12 ① ON/ST AND-By button T urn the projector on or off (pp.23-24). ② MENU button Open or close the On-Screen Menu (p.25). ⑤ Point pqt u ( VOLUME – / + ) buttons – Select an item or adjust the value in the On- Screen Menu (p.25). – Pan the image in Digital zoom + mode (p.
13 ① ST AND-By button T urn the projector off (p.24). ④ ON button T urn the projector on (p.23). ⑥ INPUT button Select a signal (pp.33-35). ⑧ SCREEN button Select the screen size (p.29). ④ ⑩ ⑭ ① ⑭ L-CLICK button Act as the left mouse button for wireless mouse operation (p.
14 ⑯ ⑮ ⑲ ⑰ ⑱ ⑱ ZOOM pq buttons Zoom in and out the images (p.29). ⑮ D.ZOOM button Select the Digital zoom +/- mode and resize the image (p.43). ⑲ FOCUS buttons Adjust the focus (p.29). ㉒ FREEZE button Freeze the picture on the screen and mute the sound (p.
15 1 2 3 Open the battery compartment lid. Install new batteries into the compartment. Replace the compartment lid. Press the lid downward and slide it. T wo AAA size batteries For correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment.
16 The eight different remote control codes (Code 1–Code 8) are assigned to this projector . Switching the remote control codes prevents interference from other remote controls when several projectors or video equipment next to each other are operated at the same time.
17 Installation For projector positioning, see the figures below . The projector should be set perpendicularly to the plane of the screen. (for PLC-XM80) P Note: • The brightness in the room has a great influence on picture quality . It is recommended to limit ambient lighting in order to obtain the best image.
18 When replacing the lens or using an optional lens, install the lens by following the instructions below . Ask the sales dealer for detailed information of the optional lens specifications. Shift the lens to the center position by using the Lens shift function (p.
19 Monitor Output BNC cable Monitor Output G B R H/V V DVI-Digital cable VGA cable VGA cable USB cable USB port Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. Cables used for connection ( ⁄ = Cables not supplied with this projector .
20 RGB Scart 21-pin Output S-video cable S-video Output Composite Video Y - Pb/Cb - Pr/Cr BNC cable Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. Cables used for connection ( ⁄ = Cables not supplied with this projector .
21 Audio Output AUDIO IN 1/2 Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. Cables used for connection ( ⁄ = Cables not supplied with this projector .
22 This projector uses nominal input voltages of 100–240 V AC and it automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor . T o reduce the risk of electrical shock, do not plug into any other type of power system.
23 Connect the projector ’ s AC power cord into an AC outlet. The LAMP indicator lights red and the POWER indicator lights green. Press the ON/ST AND-BY button on the side control or the ON button on the remote control. The LAMP indicator dims and the cooling fans start to operate.
24 Basic Operation What is PIN code? PIN (Personal Identification Number) code is a security code that allows the person who knows it to operate the projector . Setting a PIN code prevents unauthorized use of the projector . A PIN code consists of a four-digit number .
25 Side Control MENU button On-Screen Menu Remote Control POINT buttons SELECT button MENU button Basic Operation The projector can be adjusted or set via the On-Screen Menu. The menus have a hierarchical structure, with a main menu that is divided into submenus, which are further divided into other submenus.
26 Basic Operation For detailed functions of each menu, see “Menu T ree” on pages 73-75. ① Ç É Ñ Ö Ü á à Main Menu Sub-Menu â ä É Image select For computer source, used to select an image level among Standard , Real , and Image 1-10 (p.
27 The following lens operation can be made with the Lens button on the side control. Press the LENS button to enter each lens operation mode. The selected adjustment display appears on the screen. Display Lens shift on the screen. Use the Point pqt u buttons to position the screen to the desired point without having picture distortion.
28 VOLUME + button VOLUME – button MUTE (Point q ) button Side Control Basic Operation 1 2 Press the MENU button to display the On-Screen Menu. Use the Point pq buttons to select Sound . Press the Point u or the SELECT button to access the submenu items.
29 Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons enables you to make the desired operation quickly without calling up the On-Screen Menu. Press the ZOOM buttons on the remote control to zoom in and out the image.
30 Press the FREEZE button on the remote control to freeze the picture on the screen and mute the sound. T o cancel the FREEZE function, press the FREEZE button again or press any other button.
31 Remote Control POINT pq buttons KEySTONE button Basic Operation If a projected picture has keystone distortion, correct the image with Keystone adjustment. It is not available when On-Screen menu is displayed. Press the KEYSTONE button on the remote control.
32 P Note: Yo u can choose the pattern of Pointer ( Dot/Arrow / Finger ) in the Setting Menu (p.58) Y ou can move the Pointer of the projector with the remote control to emphasize a part of the projected image. Press the POINTER button to activate the Pointer function.
33 The input source changes each time you press the INPUT button on the side control or the remote control as follows: Input 1 ® Input 2 ® Input 3 ® ... Before using the INPUT button on the side control or the remote control, you must select a correct input source by On- Screen Menu and the latest input source will be displayed.
34 INPUT MENU When your computer is connected to INPUT 1 (DIGIT AL) terminal, select RGB(PC digital) . When your computer is connected to the INPUT 1 (ANALOG) terminal, select RGB (PC analog) . RGB(PC digital) RGB(PC analog) P Note: Input source changes if the INPUT 1 button on the remote control is pressed.
35 When the video input signal is connected to the Y -Pb/Cb-Pr/Cr jacks, select y ,Pb/Cb,Pr/Cr . When the video input signal is connected to the VIDEO jack, select Video . When the video input signal is connected to the S-VIDEO jack, select S-video . When connecting to video equipment, select the type of Video source in the Source Select Menu.
36 Computer Input PC System Menu PC System Menu 1 2 PC system can also be selected manually . The PC System Menu Selected system is displayed. Press the MENU button to display the On-Screen Menu. Use the Point pq buttons to select Input and then press the Point u or the SELECT button.
37 Auto PC Adjustment function is provided to automatically adjust Fine sync, T otal dots, Position H and Position V positions to conform to your computer . T o store the adjusted parameters. The adjusted parameters from the Auto PC Adjustment can be stored in the projector .
38 Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector . Manual PC Adjustment enables you to precisely adjust several parameters to match those special signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted.
39 Computer Input P Note: • Display area (H/V) cannot be selected when 480i , 575i , 480p , 575p , 720p , 1035i , 1080i or 1080p is selected in the PC System Menu (p.36). • When input computer signal to the projector , PC adjust function will become available.
40 1 2 Normal picture level preset on the projector . Picture level with improved halftone for graphics. User preset picture adjustment in the Image adjust Menu (p.42). Computer Input Image select Menu Press the MENU button to display the On-Screen Menu.
41 Computer Input Image adjust Menu Press the MENU button to display the On-Screen Menu. Use the Point pq buttons to select Image adjust and then press the Point u or the SELECT button. 1 2 Use the Point pq buttons to select the desired item and then press the SELECT button to display the adjustment dialog box.
42 Select the desired screen size that conforms to the input signal source. SCREEN MENU Provide the image at the normal computer aspect ratio of 4:3. Provide the image in its original size. When the original image size is larger than the screen size (1024 x 768), the projector enters to the panning mode automatically .
43 Provides the full screen image. Computer Input Adjust the screen scale and position manually with this function. Press the Point u button at Custom and the Custom is displayed on the screen, you can use the Point pq buttons to choose the item you want to adjust.
44 Computer Input This function is used to adjust keystone distortion of the projected image. Use the Point pq buttons to choose the item you want to adjust. Keystone This function returns all adjusted values to the factory default settings. Press the SELECT button at Reset to display a confirmation box.
45 If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PA L , SECAM , NTSC , NTSC 4.43 , P AL-M , and P AL-N . The projector automatically detects an incoming video signal, and adjusts itself to optimize its performance.
46 Normal picture level preset on the projector . Picture level adjusted with fine tone. User preset picture adjustment in the Image adjust Menu. (p.48) V ideo Input Standard Cinema Image 1 Image 2 Image 3 Image 4 Image 5 Image 6 Image 7 Image 8 Image 9 Image 10 Image select Menu 1 2 Press the MENU button to display the On-Screen Menu.
47 1 2 Press the Point t button to decrease the contrast; press the Point u button to increase the contrast (from 0 to 63). Press the Point t button to decrease the brightness; press the Point u button to increase the brightness (from 0 to 63). Press the Point t button to lighten red tone; press the Point button to deepen red tone (from 0 to 63).
48 Use the Point t u buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15). Press the Point t button to decrease the sharpness of the image; press the Point u button to increase the sharpness of the image (from 0 to 31).
49 P Note: • When no signal is detected, Normal is set automatically and the Aspect dialog box disappears. • The adjustable range for Scale H/V and Position H/V are limited depending on the input signal. • Wide cannot be operated when 720p , 1035i , 1080i or 1080p is selected on AV System Menu (p.
50 V ideo Input This function returns all adjusted values to the factory default settings. Press the SELECT button at Reset to display a confirmation box. T o reset, press the SELECT button at “Y es.” Ceiling Rear When this function is set to On , the picture will be top/bottom and left/right reversed.
51 Setting Setting Menu Press the MENU button to display the On-Screen Menu. Press the Point pq buttons to select Setting and press the Point u or the SELECT button to access the submenu items. 1 2 Use the Point pq buttons to select the desired item and then press the Point u or the SELECT button to access the selected item.
52 This function decides whether to display On-Screen Displays. On ............................... Show all the On-Screen displays. Use this function when you want to project images after the lamp becomes bright enough. The factory default setting is in this option.
53 Setting Off Logo select Capture Capture This function enables you to capture an image being projected to use it for a starting-up display or interval of presentations. Select Capture and press the SELECT button. A confirmation box appears and select y es to capture the projected image.
54 Setting Enter a Logo PIN code Use the Point pq buttons to enter a number . Press the Point u button to fix the number and move the red frame pointer to the next box. The number changes to ⁄ . If you fixed an incorrect number , use the Point u button to move the pointer to the number you want to correct, and then enter the correct number .
55 This function allows you to change brightness of the screen. Lamp life control Lamp control Select the lamp operation when the total lighting time of a lamp exceeds the recommended total hours of use. Mode 1 ............ A lamp can be turned on even after exceeding the recommended total hours of use.
56 Choose the running speed of cooling fans from the following options. Normal ...... Operate in this mode under normal conditions. Max ........... Use this mode when you want to increase the cooling effect when operating the projector in high ambient temperature environment.
57 P Note: Factory default is Ready: 5 Min . Setting Select a location of the infrared remote receiver of the remote control. See “Remote Control Receivers and Operating Range” on page 15 for details. All ............ Activate all of the receivers.
58 Setting When this function is set to On , the projector will be automatically turned on just by connecting the AC power cord to the wall outlet. P Note: Be sure to turn off the projector properly (see “T urning Off the Projector” on page 24).
59 Setting Key lock Key lock PIN code lock This function locks the side control and remote control buttons to prevent operation by unauthorized persons. ...... Unlocked. ...... Lock the operation of the side control. T o unlock, use the remote control.
60 Setting Use the Point pq buttons to select Off , On1 or On2 . Press the SELECT button to close the dialog box. Change the PIN code lock setting Enter a PIN code Use the Point pq buttons to enter a number . Press the Point u button to fix the number and move the red frame pointer to the next box.
61 Setting When you want to make a digital processing of a projected image faster , set this function. Use the Point pq buttons to select On or Off . Video delay control Closed caption Closed Caption is a printed version of the program sound or other information displayed on the screen.
62 This function returns all setting values except for User logo , PIN code lock , Logo PIN code lock , Lamp counter , and Filter counter to the factory default settings. V arious test pattern are available for use when setting up the projector . Filter warning icon appears on the screen at a set time.
63 Filter prevents dust from accumulating on the optical elements inside the projector . Should the filter becomes clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely af fect the life of the projector .
64 T urn off the projector , and unplug the AC power cord from the AC outlet. First, clean up the dust on the projector and around the air vents. 1 2 Press q downwards on the filter cover to release the latch and open the filter cover . 3 Put the new one back into the position and close the filter cover .
65 Filter counter Maintenance and Care Be sure to reset the Filter counter after cleaning or replacing the filter . Press the MENU button to display the On-Screen Menu. Use the Point pq buttons to select Setting and then press the Point u or the SELECT button.
66 T urn off the projector and unplug the AC power cord. Let the projector cool for at least 45 minutes. Loosen the screw and open the lamp cover . Loosen 3 screws of the lamp and pull out the lamp by using the built in handle. 1 3 Replace the lamp with a new one.
67 ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer . When ordering, give the following information to the dealer . ü Model No. of your projector : PLC-XM80, PLC-XM80L ü Replacement Lamp T ype No. : POA-LMP137 (Service Parts No.
68 Unplug the AC power cord before cleaning. Gently wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner , or use a lens cleaning paper or commercially available air blower to clean the lens. Avoid using an excessive amount of cleaner .
69 Maintenance and Care The W ARNING indicators show the state of the function which protects the projector . Check the state of the WARNING indicators and the POWER indicator to take proper maintenance. The projector is shut down and the W ARNING TEMP .
70 Before calling your dealer or service center for assistance, check the items below once again. 1. Make sure you have properly connected the projector to peripheral equipment as described on pages 19-21. 2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly connected.
71 The image is out of focus. – Adjust the focus of the projector . – Check Projection Lens to see if it needs cleaning. P Note: Moving the projector from a cool temperature location to a warm temperature location may result in moisture condensation on Projection Lens.
72 W ARNING: High voltages are used to operate this projector . Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center . Specify the model number and explain about the problem.
73 Input RGB (PC analog) Y , Pb/Cb,Pr/Cr RGB (Scart) RGB (PC digital) RGB (A V HDCP) Video RGB Video Y , Pb/Cb,Pr/Cr S-video Input 3 Input H-sync freq. V -sync freq. Information Screen Language Lamp status Power management Remote control P Note: The Menu display varies depending on the input signal.
74 P Note: The Menu display varies depending on the input signal. System (2) Auto PA L SECAM NTSC NTSC 4.43 P AL-M P AL-N System (3) Auto 1080i 1035i 720p 575p 480p 575i 480i Image select Standard Cin.
75 Setting Language Fan control Blue/User/Black 12 languages provided Menu position Lamp control All/Front&T op/T op&Back/Front&Back/Front/T op/Back Normal/Max Power management Background .
76 Check the indicators for the projector condition. Indicators Projector Condition POWER green LAMP red W ARNING TEMP . red W ARNING FIL TER orange P-MANAGEMENT ST AND-BY blue LAMP REPLACE orange The projector is off. (The AC power cord is unplugged.
77 The projector is detecting abnormal condition. Indicators Projector Condition POWER green LAMP red W ARNING TEMP . red W ARNING FIL TER orange P-MANAGEMENT ST AND-BY blue LAMP REPLACE orange The temperature inside the projector is elevated close to the abnormally high level.
78 The projector is detecting abnormal condition. Indicators Projector Condition POWER green LAMP red W ARNING TEMP . red W ARNING FIL TER orange P-MANAGEMENT ST AND-BY blue LAMP REPLACE orange If the Filter counter reached a time set in the timer setting, a Filter warning icon (Fig.
79 ON-SCREEN DISPLA y RESOLUTION H-Freq. (kHz) V -Freq.(Hz) VGA 1 640x480 31.470 59.880 VGA 2 720x400 31.470 70.090 VGA 3 640x400 31.470 70.090 VGA 4 640x480 37.860 74.380 VGA 5 640x480 37.860 72.810 VGA 6 640x480 37.500 75.000 VGA 7 640x480 43.269 85.
80 ON-SCREEN DISPLA y RESOLUTION H-Freq. (kHz) V -Freq.(Hz) D-VGA 640x480 31.470 59.940 D-480p 720x480 31.470 59.880 D-575p 720x575 31.250 50.000 D-SVGA 800x600 37.879 60.320 D-XGA 1024x768 43.363 60.000 D-WXGA 1 1366x768 48.360 60.000 D-WXGA 2 1360x768 47.
81 Mechanical Information Projector T ype Multi-media Projector Dimensions (W x H x D) PLC-XM80L :19.25” x 6.46” x 14.61” (489.5 mm x 164.0 mm x 371.1 mm) PLC-XM80 : 19.25” x 6.46” x 17.12” (489.5 mm x 164.0 mm x 434.8 mm) Net Weight PLC-XM80L : 18.
82 The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector for wide variety of uses. For installation and replacement of the lens, always contact the sales dealer . The projector lens must be installed or replaced by well-trained sales or service engineers.
83 ANALOG/ MONITOR OUT (Mini D-sub 15 pin) 5 1 2 3 4 10 9 6 7 8 15 14 13 11 12 CONTROL PORT CONNECT OR (D-sub 9 pin) ----- R X D T X D ----- SG ----- RTS CTS Serial 1 2 3 4 5 6 7 8 DIGIT AL DVI-D (DVI 24 PIN) 1 9 17 2 10 18 3 11 19 4 12 20 5 13 21 6 14 22 7 15 23 8 16 24 T .
84 Write down the PIN code number in the column below and keep it with this manual securely . If you forgot or lost the number and unable to operate the projector , contact the service center . Factory default set No: 1 2 3 4* Factory default set No: 4 3 2 1* * Should the four-digit number be changed, the factory set number will be invalid.
85 Unit: inch (mm) Appendix Dimensions Screw Holes for Ceiling Mount Screw: M6 Depth: 0.393 (10.0) 3.31(84.0) 16.39(416.2) 6.46(164.0) 5.91(150.0) 19.27(489.5) 7.25(184.2) 3.34(84.7) 6.67(169.5) 14.61(371.1) 6.25(158.8) 5.91(150.0) 6.89(175.0) 2.95(75.
86 Appendix This projector provides a function to control and monitor the projector's operations by using the RS-232C serial port. Connect a RS-232C serial cross cable to CONTROL PORT on the projector and serial port on the PC.
87 The command is sent from PC to the projector with the format below; 'C' [Command] 'CR' Command: two characters (refer to the command table below .
88 Appendix The command is sent from PC to the projector with the format below; 'CR' [Command] 'CR' Command: one character (refer to the command table below .
KW8AL.
Een belangrijk punt na aankoop van elk apparaat Sanyo PLC-XM80L (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sanyo PLC-XM80L heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sanyo PLC-XM80L vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sanyo PLC-XM80L leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sanyo PLC-XM80L krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sanyo PLC-XM80L bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sanyo PLC-XM80L kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sanyo PLC-XM80L . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
